Search Documents

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

By Heidi Beers

Teijin Limited ? Global technology-driven group operating in six main fields Advanced fibers and composites business group Healthcare business group Trading and retail business group IT business group New business development group Electronic materials and performance polymer products business group ? Listed on Tokyo and Osaka stock exchanges ? 150 companies and around 17,000 employees worldwide ? Consolidated sales of USD 9.1 billion*

Aug 1, 2013

By Frank G. Wickert

One key to maintaining successful mining operations in today?s global economy is in having the ability to access real-time machine operating data ([1] G. Brown, B. Ebacher, W. Koellner,2000)([2] Brochure of Siemens E&A, Order Number 141000-1). With recent and ongoing advances in mining equipment systems it is imperative that mine managers have full knowledge of the status of their equipment at any given point in time. This knowledge is critical to ensuring that the productivity of each and every machine is maximized. Knowledge of machine status is only the first step, however, in controlling and optimizing a piece of mining equipment. Computer based diagnostic systems, traditionally offered on mining equipment, have provided a link for collecting data and trouble-shooting problems as they occur. One problem existed, though, that those systems stopped short of providing full drive systems access. A maintenance technician could see the data but to make critical adjustments or make repairs the technician needed to be on the machine. In extreme cases the machine would be down until OEM assistance could reach the mine site. The key then to reducing down-time and maximizing machine productivity was creating a system that could not only monitor drive systems but also provide remote access to those systems. Essentially a link needed to be created through which a technician could gain drive access remotely then make adjustments or repairs without being on the piece of equipment. This paper will introduce AccessDirectTM, a new remote diagnostic system for Bucyrus mining shovels and draglines. AccessDirectTM combines all three important elements of remote diagnostics: ? Vital Signs and Production Monitoring (SiRAS-M) ? Automatic analysis (SiRAS-A) of faults, and tracking of trends for preventive and reliability centered maintenance , and ? Fast, direct Intervention (SiRAS ? I) for troubleshooting support, repairs, and system optimization.

May 1, 2002

By Theophile S. Yameogo

Les ressources naturelles ont en général été le moteur du développement économique et social des nations. Les pays aujourd?hui développés sont pour la plupart d?anciens eldorado, charbonniers ou pétroliers. D?autres le sont toujours. L?Afrique fait cependant figure d?exception : même en étant comblé de ressources naturelles exceptionnelles, les pays de ce continent croulent sous le poids de la pauvreté et de ses acabits que sont les maladies, la famine, la guerre et l?insurrection sociale. On reconnaît néanmoins qu?il y a des cas particuliers comme le Botswana, la Namibie, l?Afrique du Sud. Face à cette situation, beaucoup de scénarii ont été proposés sans pour autant porté les fruits espérés. Le rapport Brundtland suggère que le développement durable est la clé du succès car elle veille à la prospérité économique, à l?équité dans la société et à la pérennité dans l?environnement. Pour l?Afrique, beaucoup de facteurs doivent être considérés et les solutions se doivent d?être pratiques et éthiques. Le futur ingénieur des mines qui a écrit ce rapport, apporte sa vision de la situation non sans avoir auparavant analysé les faits. Cette démarche, qui se veut avant tout éthique, inclut les aspects sociaux, économiques et politiques. Introduction In the 40s, 50s and the 60s, many economists, among which Harold Hotelling from South Carolina University, thought that developing countries could reach socio-economical success by extracting their natural resources such as oil and minerals. The current economical disaster seems to have contradicted that belief and critics like Davis Graham (Colorado School of Mines) and Michael Ross (University of California at Los Angeles) even suggested that extractive activities stop in Africa. But the experts of the World Bank (Mining Department) and some mining and oil companies are committed to reverse the tendency by implementing a new approach. Considering the principles of sustainable development defined in the Brundtland report (1987), we decided to analyze the possibility of giving the extractive industry a catalytic role in creating a socially, economically and environmentally development in Africa. In other words, can we continue to mine and extract oil in Africa for its blossoming future under the ruling of the sustainable development? In the following, we start by explaining the African socio-economic and political context. After a brief definition of the sustainable development, we explain why, for Africa, some believe in the extractive industry and some don?t. In the end, we draw out conciliatory arguments.

Apr 1, 2005

By Bruce Conard

For many years, Bruce Conard has been engaged in reading about and discussing the desired sustainability of the mining and metals resource industry. He has, however, become concerned that there is a greater issue that requires our urgent attention: what challenges do we face as a global society? His Distinguished Lecturer presentation traces the idea of environmentally sustainable economic development but concludes that a business’ interest in its sustainability is predicated on the sustainability of our global society. Conard reviews some of the most serious challenges, including population growth, clean energy supplies, freshwater availability and climate change, and calls on scientists and engineers not only to apply their skills in helping solve these challenges, but most urgently, to speak with intelligence and passion about the need to act now.

Jan 1, 2014

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By T. Holmes

Investigations reveal that the throughput difference between a perfect production day and the average is often on the order of 40%, and that bulk solids handling system deficiencies are the largest (>50%) class of lost opportunities. Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. To reduce or eliminate bulk solids handling problems in an existing system requires an analysis of troublesome handling equipment – for example, a concentrate transfer chute that experiences plugging, poor flow to the furnace, unacceptable dust generation, and spillage. These problems often lead to significant maintenance costs related to downtime and personnel time. Understanding the cause and cost of flow issues is the first step in troubleshooting the problem. Next, measuring the material’s flow properties is critical to providing design data required to develop a comprehensive scientific solution. In the case of a new installation, the design data is required to properly design the system right first time and prevent flow problems from occurring so that the new equipment works correctly from start-up. This paper highlights the cost of material handling problems and discusses the best approach to evaluate material handling system deficiencies. A case study is given of how Anglo American's operation in Barro Alto Brazil enjoyed a 5-month payback from a bulk solid transfer chute debottleneck project. INTRODUCTION When operating a plant or designing a greenfield or brownfield operation, the intent is to have perfect production days (PPD) each and every day. Money is made by moving material through the plant in a controlled manner to produce the desired product. Mining operations and copper concentration processes are at the most basic level a practice in bulk solids handling (BSH). Unfortunately, many of the project planning steps are overlooked, particularly related to BSH. Investigations reveal that the throughput difference between a PPD and the actual average is often on the order of 40%, and that BSH system deficiencies are the largest (>50%) class of lost opportunities (Wellwood, 2017). Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. BSH issues are essentially baked into the fabricated plant and left to operations to accept the deficiencies and deal with them for the life of the mine. These deficiencies then become part of the normal operation of the mine and plant.

Jan 1, 2019

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By Vladimir N. Rudashevsky, Louis J. Cabri, Nikolay S. Rudashevsky, Thomas Oberthür

"EPD (Electric Pulse disaggregation) and HS (hydroseparation) are exceptional technologies for research, concentration, evaluation, and mineral extraction of specific minerals such as precious metals (Au, Ag, PGM), kimberlites (extraction and concentration of indicator minerals), zircons and baddeleyite (recovery of objects for geochronology), and even gemstones (method of evaluation and production of the 100% gemstone concentrate of ideal crystals) etc. EPD is used for recovery of pristine undamaged crystals of diamond, emerald, ruby, sapphire etc, including large crystals. It was tested on various hard ores and was especially successful for recovery of “soft” minerals from “hard” matrix. EPD products are very convenient for HS processing, resulting in representative concentrates of all heavy minerals including the finest particles (5-10 µm). The combined EPD and HS method enables high sensitivity (20 ppb) for evaluation of precious metal ores providing objective information about original grain size, associations, and recovery using a very small amount of sample (1-3 kg). Latest developments of EPD and HS techniques at CNT Mineral Consulting Inc. include the HS-21 hydroseparator (50 kg/hr) and the Spark-21 EPD (5 t/hr), which enables use of both techniques for prospecting and mineral processing of industrial size samples of certain ores.INTRODUCTIONThe main task for mineral processors is to find a reliable technology for testing of mining feasibility and the efficiency of mineral extraction procedures. Among various mineral processing approaches of extraction and concentration there are two alternative cost-effective methods that can be described as the most environmentally benign and complementary: electric-pulse disaggregation and hydroseparation. These techniques were tested on many different ore types and process products with great success providing a precise and comprehensive mineralogical determination of different accessory precious metal and other useful minerals constituent in rocks, ores, and tailings.This article describes several examples of EPD and HS use: native gold from the Kostomuksha deposit (Karelia, Russia), a Ag-Au deposit in South America, zircons from ancient ultramafic igneous rocks of SW Greenland, bauxites of West Australia, PGM from the Driekop dunite pipe and gemstones (ruby, sapphire, emerald and demantoid) from different deposits."

Jan 1, 2008

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By S. Bellec, A. Berton

"Usually, steady state mass balances are used for the design of mineral processing plants. However, this tool does not take into account the impact of process inputs variability nor does it evaluate process transient behaviours between stationary states, such as mill start-up and shutdown. The use of advanced simulations enables the integration of dynamic behaviours in process design decision-making by highlighting situations that are undetectable by using only steady state mass balances. Applying these simulation tools to brown field projects allows the simulator performances to be calibrated and validated on actual plant data before it is used as a prediction tool for the modified plant.Three (3) simulators were implemented at the design stage of a major upgrade project for an ore processing plant in order to assess process behaviours under different production scenarios. These simulators were built to evaluate the impacts on major elements such as mine production, ore stockpile, concentrator production as well as water demand. A validation of individual equipment models was performed whenever sufficient measured data was available. The simulators were then used to study the impact of ore variability (grade, hardness, throughput), to assess day-to-day production special events, and to evaluate the true stockpiles live capacity.The use of a stochastic simulator for equipment sizing allowed a more precise sizing of many pieces of equipment and avoided important expenses in the fresh water pumping system. The dynamic simulator also confirmed that the water in place system would suffice, even in the most demanding production scenario. Finally, the stockpile simulator allowed an important production bottleneck to be quantified and then made possible the assessment of various practical solutions for the stockpiling-reclaiming issues.Post start-up, process data underlines the fact that using advanced simulation tools was useful to mitigate process-related risks associated to the plant expansion, showing generally accurate prediction and adequate equipment sizing, leading to smooth process commissioning. The presented methods are part of what is now routine in Soutex’s participation in both greenfield and brownfield projects."

Jan 1, 2015

By Adam Moore, Ryan Gillespie, Jarrett Quinn, Audrey Walters, Peter Radziszewski

"Vale Long Harbour Processing Plant (LHPP) was designed to process Voisey’s Bay nickel concentrate into finished nickel and associated copper and cobalt products. The plant includes a secondary grinding circuit comprising two Stirred Media Detritors (SMDs) operating in parallel. The ultrafine grinding circuit was designed to process concentrate at a rate of 33 t/h and produce a ground product (P80) of 20 µm to feed the leach circuits. Start-up of the grinding circuit at LHPP was undertaken in December 2014.The objective of this paper will be to describe the design, commissioning, start-up and performance of the secondary grinding circuit with a focus on the two Metso SMD-355-C mills. Following a brief overview of Vale’s LHPP and the SMD technology, the paper will review the design of the SMD secondary grinding circuit from lab tests through to scale-up performance prediction. This will be followed by the results of circuit commissioning outlining some of the issues raised and addressed after which SMD performance will be outlined. Specifically, the SMD circuit grinding performance will be examined since start-up which will include the effect of media size and wear on grinding. Furthermore, impeller wear will be examined by determining initial “shear volume” and worn “shear volume” as well as its effect on mill power and the means to maintain it. The paper closes with a discussion on grinding performance."

Jan 1, 2016

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009