Search Documents

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By S. B. Ballantyne, D. R. Boyle

"Detailed studies have been conducted on the dispersion of uranium in stream waters and sediments around various types of mineralization and hitherto unexplained anomalous areas in the Okanagan Valley and Highland region of south-central British Columbia. These studies were part of the jointly funded and planned Federal-Provincial Uranium Reconnaissance Program of the Geological Survey of Canada and the British Columbia Ministry of Energy, Mines and Petroleum Resources. Statistical analysis of regional data indicates that U in stream waters and sediments varies considerably for different rock types, thus affecting data interpretation. In addition, the data demonstrate a poor correlation between U in stream waters and their associated sediments which can be largely accounted for by variations in climate and water and sediment composition. Regional trends in the distribution of U can be explained in terms of the above secondary factors as well as primary metallization phenomena.Significant correlations between U and F, and U and Mo can be explained by certain magmatic and mineral-forming processes. U shows little correlation with other base metals.The dispersion characteristics of U in the vicinity of Miocene "" basal type "" mineralization ; uraniferous pegmatite terranes, anomalous lineaments in granitic terranes and high-background volcano-sedimentary areas are discussed. Highly anomalous U concentrations in waters and sediments may not always be indicative of mineralization, and guidelines for interpretation require a sound knowledge of the geological and secondary processes operative in the area."

Jan 1, 1980

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By Arthur Barnes, Mika Muinonen, M. J. Lavigne

"The carbothermic reduction of chromite ore to produce high carbon ferrochromium is among the most energy intensive metal extraction processes performed, due not only to the highly endothermic nature of the reduction reactions but also the very high operating temperatures required for the smelting operation to separate the chrome-containing alloy from the discard slag.KWG Resources and XPS have collaborated over the last 3 years in developing a patented (Winter) processing alternative to the traditional smelting operation in which all processing takes place in the solid state at temperatures many hundreds of degrees lower than those required for liquid processing. Amongst the attractions of the process are much lower capital costs, as well as reduced operating costs, particularly of energy.A techno-economic study on the new process identifies a reduction in overall energy consumption of 70% against conventional processing and approximately 40% lower than the current best practice. By utilising more natural gas than coal based energy sources, the KWG process is able to show an overall 50% reduction in greenhouse gas emissions compared with the most energy efficient current practice. The impact of the new process on future processing is therefore regarded as highly significant, with global energy reductions equivalent to the effect of completely eliminating energy demand from a country the size of Italy.The study concluded that the potential for this process to completely revolutionise the global ferrochrome industry should not be underestimated. Its impact reaches far beyond exploitation of a regional natural resource."

Jan 1, 2015

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By J. H. McMillan

Most of the recent papers read before the Institute have dealt with purely scientific matters, or with experiences in the various phases of mining operations. Very little, if anything, has been said concerning the part played by the human element in the industry. It is now opportune to consider this vital factor if we are to cope with the complex work of the present-day miner and, at the same time, meet the demands of the executive for greater efficiency. It is time we made an inventory of our knowledge to determine if we are absorbing the information so essential to modern mining practice. We must keep in close touch with all new ideas and developments in our chosen field and keep ourselves up-to-date in regard to everything pertaining to mining operations in general. The man who ceases to study ceases to advance. There are men who on attaining an executive chair give up all study, because they think they have reached the pinnacle of success. Modern industrial business, and coal-mining is no exception, demands that executive officers shall be 'live wires' -- men who are not only well-informed as to their immediate duties, but who are closely in touch with all matters of importance affecting the industry as a whole. We may be graduates of schools and colleges, but the training we receive in these institutions is only the foundation for our later work. Certainly no executive officer can know too much concerning the work he is engaged in, and the more he knows the more pleasure he will get out of his work.

Jan 1, 1925

By A. M. Glendinning

"IntroductionLocationTHE PROPERTY of Aunor Gold Mines, Limited is in Deloro township, Ontario, about three miles southeast of the town of Timmins. It consists of a group of eleven claims located between those of Buffalo-Ankerite Gold Mines, Limited, and Delnite Gold Mines, Limited.GeologyThe ore zone at the Aunor mine consists of a narrow band of fine grained pillowed andesite, irregular bands of 'brown to green carbonated andesite, and lenticular bodies of quartz feldspar porphyry. The zone strikes N.80°E., dips 60 North, and has been traced for 5,000 feet across the property. It varies in width from 0 to 250 feet and is bounded on the north and south by masses of dark bluish-grey tale chlorite schist. These schist bands have widths up to 500 feet.The ore occurs in a series of parallel and branching veins confined to the limits of the zone. These veins tend to terminate and die out on the footwall schist contact, striking generally parallel with the ore zone. In wide sections of the zone, 150 to 250 feet, the veins range in width up •to 3.5 feet and may occur in two or three horizons across the width of the zone, each mineable independent of the other. They tend to dip a little flatter than the general dip of the zone. Where the zone is narrow, the veins are so closely spaced and numerous they can be mined together and in some places the complete zone has been mined from schist to schist."

Jan 1, 1953

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By J. Doucet, C. Price

In an industrial setting, operational changes are continually introduced, driven by new technologies or changing economics. Because of day-to-day variability, quantifying the impact of these changes based on metallurgical performance requires long trial periods to achieve statistically significant results. Tools and techniques developed by the mineral processing group at McGill University have allowed for direct measurement of process variables (e.g., bubble size, gas and solid holdup). Two case studies are described where direct measurement techniques were used to evaluate: a) a new rotor stator mechanism; and b ), the introduction of a new frother type. Application of these methods has accelerated the evaluation of process changes and improved confidence in results.

Jan 1, 2009

By B. R. MacKay

Introduction Of all Canada's mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932

By N. K. Jaber

The "Pidgeon Process" for the extraction of magnesium from dolomite ore utilizing ferrosilicon as the reducing agent has been studied extensively by active metallurgists such Mr L,M, Pidgeon the father of this process, Most of the work sited so far has focused on heating the (FeSi/MgO,CaO) briquette mix under vacuum in stainless steel retorts by external fuel hydrocarbon heating, In this work Electrical Induction Heating was employed as the heating method whereby the briquette mix was placed in a steel crucible around which an Induction Heating copper coil was wound and placed inside in a stainless steel vacuum tank, It was observed that by virtue of the fast Induction Heating method utilized in the silicothermic extraction process higher reduction temperatures were reached in shorter periods of time due to fast heat transport into the ore charge mix, This facilitated shorter metal reduction times as compared to the conventional fuel heating methods.

Jan 1, 2006

By C. W. Reno

"THE LORNEX MINING PROJECT is one of several large-tonnage, low-grade operations recently placed in operation in British Columbia. It is located in the Highland Valley in the south central portion of the province. This area is described as a divide valley at an elevation range of 4,000 to 6,000 feet and is situated on the divide between two drainage systems. The major drainage to the west flows into the Thompson River and to the east and south the drainage enters the Nicola River system. This open-ended valley lies between low, rounded mountains in fairly heavily-wooded country. Prior to the commencement of copper mining activities, the first by Bethlehem Copper Corporation Ltd. over ten years ago, the valley was only sparsely settled. A few small ranches were in existence on the several Indian Reserves located along the valley bottomland. There has also been a small amount of logging activity in the valley, although much of the area is covered by dense lodgepole pine which has little or no value to the loggers. As the mining interest mounted with further discoveries of the disseminated copper ore typical of the district, much of the valley was covered with mineral claims and exploration drilling was carried on by several companies at various times. At the time Lornex was preparing to commence major construction work in early 1970, there was very little activity of any kind in the Highland Valley outside of the Bethlehem operation and a small amount of ranching."

Jan 1, 1973

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By D. H. Ryan, J. T. Graham, A. Navarra, J. A. Finch, S. Somot

Pyrrhotite (Po) is widely considered to be the most significant mineral in the self-heating of sulphides. It is therefore desirable to determine the amount of Po in mineral samples. This is commonly accomplished through x-ray diffraction (XRD) or quantitative evaluation of materials by scanning electron microscopy (QEM-SEM). This paper introduces another quantitative method based on Mossbauer analysis that requires limited sample preparation and has the additional potential to detect the sulphur/iron ratio within Po. The technique is explored using pentlandite/pyrrhotite mixtures.

Jan 1, 2009

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By K. Trapani

"The study undertaken aims to investigate an ice stope heating and cooling system for its potential to be implemented in sub-arctic mines, as a low carbon alternative to conventional natural gas and refrigeration chiller systems. Its performance was simulated for a years’ worth of data, taking into consideration hourly temperature data. Results showed that to supply the required heating and cooling loads, the ice stope system had to supplement its heating with natural heating. The techno-economic performance of this system was compared to that of a conventional heating and cooling system in a mine, with the ice stope thermal storage system hawing the lowest annuitized cost and significantly lower carbon emissions.INTRODUCTIONConventional heating and cooling, in a mine is implemented using natural gas heaters and chiller refrigeration systems respectively. This results in a significant portion of energy consumption in underground mines attributable to ventilation (De Souza, 2015), including the conditioning of the air to ensure that temperatures do not exceed work comfort standards (ACGIH, 2011). Especially at depth where heat could become a significant issue. An ice stope thermal storage, using ice as the storage medium is being proposed as an alternative to provide the heating and cooling—with the ice creation resulting in heating and the ice melting providing the cooling required. A techno-economic investigation of the two systems is undertaken to identify the capital and operating costs for the two systems, and to assess the ice stope’s potential to be considered a low cost and carbon solution for heating and cooling of mines in sub-arctic climates.NATURAL STORAGE SYSTEM – CONCEPT DEVELOPMENTThe concept for the natural storage system is developed from the ice stope at Frood-Stobie Mine, ON, Canada (Stachulak, 1991). The ice stope was developed for mine air heating, with the heating occurring by spraying warm return service water onto the cold intake air—resulting in the air temperature increasing and ice being created in the stope. In summer this ice was melted by passing warm air on top of it, resulting in slight cooling of the air but no significant temperature difference which could allow effective cooling. A schematic of the Frood-Stobie Mine ice stope is provided in Figure 1."

Jan 1, 2019