Search Documents

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By W. P. Campbell

THE investigation herein described had its beginning in the chemical laboratory of the Department of the Interior, Calgary. After the transfer of the natural resources to the Province of Alberta in 1930, the laboratory was closed and the investigation discontinued, but in 1933, with the permission of the Director of the Mines Branch, the work was again taken up and brought to completion. OBJECT OF THE INVESTIGATION The object of the investigation as originally planned may be stated as follows : (1) To determine the chemical composition of the limestone formation underlying Turner Valley gas field. (2) To identify 'beds' in the limestone, if such existed, with definitecharacteristics which would mark them from immediately overlying and underlying measures. (3) To relate information acquired on the composition of the limestone to the occurrence of oil and gas in the particular section examined. Definite information was lacking as to the exact chemical composition of the limestone and of its variations in composition at various depths. The formation was generally referred to in the field as the 'dolomitic' limestone, but the depth to which the dolomitized zone extended and the degree to which the limestone generally had become dolomitized were not known. Jn the drilling and logging of wells, the recognition of suitable 'markers' in the various formations is a matter of some importance. Markers are generally relatively small but widespread members of a formation, which have some characteristic property, of colour, composition, or form, by which they may be identified, and with them, consequently, the formation of which they form a part. In the formations above the limestone in Turner Valley, a number of well defined and easily recognized markers are known to geologists, drillers, and others interested in the field. Many of these markers Hand out in sharp contrast to adjoining measures and are therefore easily recognized; in others, the contrast is less sharp, with consequent difficulty in identification.

Jan 1, 1937

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By Fred G. Hewett

The Cassiar orebody is located in a sill-like serpentinite body intrusive into the Devonian-Mississippian sedimentary rocks of northern British Columbia. Subsequent intrusion of the Cassiar batholith formed the McDame synclinorium and produced chrysotile asbestos. Present information indicates an orebody of approximately 16,277,000 tons amenable to open-pit mining, but continued diamond drilling will be needed to accurately define total tonnage and grade. A program has been developed at the mine to provide the required information on a daily basis, and work is continuing on more effective dollar-value prediction methods.

Jan 1, 1978

By J. C. Underwood

"The wear performance of grinding balls under conditions of impact and abrasion is affected by their chemical composition and structure. The selection of appropriate analyses and heat treatments that will provide both abrasion and impact resistance takes into account the effects of certain elements on structure and harden-ability, as well as the over-all effect of composition and hardness penetration on the residual stress pattern developed through heat treatment. Direct quenching from forging temperatures substantially increases hardenability over that obtained in reheat-quench practices, and can be done without undue risk of damage to the ball provided that the harden-ability bears the correct relationship to ball diameter.Average volumetric hardness and percent hardened volume are convenient parameters for quantitatively expressing the response to heat treatment and indicating anticipated wear properties. A number of factors which can lead to reduced wear life as a result of material or processing problems are reviewed and illustrated."

Jan 1, 1959

By C. Bergstrand

"Precipitation of gypsum and the formation of scale may pose a serious challenge in the leaching of several minerals. As an example, precipitated gypsum may form scale in the machines increasing the need for maintenance. Alternatively, it may encapsulate precious elements, i.e. gold and lower the recovery during subsequent leach processes. In this work we explore how different biopolymers modify the rheology of gypsum at three different pH levels at ambient and elevated temperatures. The ability to disperse gypsum vary with temperature, pH and biopolymer. It is also inversely related to the scaling potential. Measurements of the zeta potential as a function of increasing amounts of biopolymer reveals that the magnitude of the zeta potential changes in the presence of biopolymer, and so does the ability to disperse the gypsum suspension. Similar results with hematite will also be discussed. The methodology and results may aid in the selection of additives used in mineral processing applications where scale pose a problem.INTRODUCTION Processing of refractory gold ores normally involve either atmospheric or oxidation under pressure in order to convert sulfides to oxides (Weir, King, & Robinson, 1986; Weir, Robinson, & King, 1986). This conversion facilitates leaching of gold (and silver) in normal CIL processes. During oxidation, sulfides are converted to sulfates. Normally, there is an abundance of calcium ions in the process water, either released from the ore or added as lime to adjust pH for the CIL process. Precipitation of calcium sulfate, or other compounds (calcium carbonate, jarosite, hematite) is a way to remove gangue minerals from the solution entering the CIL circuit (Ji, King, Fleming, & Ferron, 2010). Precipitation may also cause challenges in the process as gold (or other valuable elements) may become encapsulated in gangue. (Beauchamp, Choung, & Xu, 2006). In addition to precipitation, the precipitated gangue minerals may solidify and form scale in the processing equipment. Recently, Lauten and Kluck (2016) found that dispersants used as scale inhibitors to prevent encapsulation of gypsum did not modify the solubility of gypsum. In the utilised model system, similar amounts of gypsum precipitated with and without dispersants. Instead, it was found that the dispersants evaluated as scale inhibitors reduced the yield stress of gypsum suspensions. The reduced yield stress was associated with a reduced tendency for gypsum particles to agglomerate and form scale."

Jan 1, 2017

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Doris Stüben, Geoffrey P. Glasby, Akira Usui, Jörg-Detlef Eckhardt, Bruce W. Mountain, Zsolt Berner

"Abstract - Twenty-seven marine Mn and Fe deposits chosen for their diverse origins have been analyzed for five platinum-group elements (PGE). The PGE display their highest concentrations in hydrogenous Mn crusts and nodules, lesser concentrations in diagenetic nodules and two to three orders of magnitude lower concentrations in hydrothermal Mn and Fe crusts. This difference of behavior reflects the well-known fractionation of Mn and Fe from the other transition elements, rare earth elements (REE) and PGE in hydrothermal Mn and Fe crusts. Pt, Ru, Rh, and Ir show a close geochemical coherence in these deposits and are differentiated from Pd which shows a negative anomaly with respect to the other PGE in hydrogenous and diagenetic Mn deposits. Pd is less depleted than the other PGE and the Pd anomaly much less pronounced in the hydrothermal Mn and Fe crusts relative to the hydrogenous and diagenetic Mn deposits.Stability field diagrams show no evidence for the oxidation of Pt to the tetravalent state in seawater as suggested by some authors. Rather, Pt appears to be present in seawater as Pt(OH)2 0. Adsorption of Pt(OH)2 0 onto the surface of Mn and Fe oxyhydroxide minerals may explain the enrichment of Pt in marine Mn deposits. However, Pt metal is the thermodynamically stable solid phase of Pt under seawater conditions and reduction of Pt(OH)2 0 to Pt metal, particularly in the vicinity of the oxygen minimum zone, is possible, although the high Ce/La ratios of the Co-rich Mn crusts do not support this hypothesis. Pt, Ru, Rh, and Ir display their maximum concentrations in the Corich Mn crusts. This may reflect, among other things, the low growth rates of these deposits. The stability field diagram of Pd shows that Pd is undersaturated in seawater and occurs in seawater dominantly as PdCl4 2- and anionic mixed-hydroxide-chloride complexes. This would explain the anomalous position of Pd among the PGE with respect to its uptake into marine Mn deposits. A study of inter-element associations indicates that the incorporation of the PGE from meteoritic dust plays only a minor role in the uptake of these elements into marine Mn deposits. The PGE remain the most poorly studied group of elements in marine Mn deposits. The data presented here emphasize the need for the establishment of a more comprehensive database of the PGE in marine Mn deposits in order to understand more fully their uptake into marine Mn deposits and their pathways through the oceans."

Jan 1, 1999

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada's imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By Barry D. Simmons

"A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck's approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-l990s and the company is confident that this target will be achieved.IntroductionAs one of Canada's oldest continuously operating mining companies, Teck Corporation traces its roots to Kirkland Lake, Ontario, with the development of the Teck-Hughes gold mine in 1913, later supplemented by production from the Lamaque gold mine in Val d'Or, Quebec. Control of the company was acquired by Temagami Mining Company, part of the Keevil Mining Group, in 1959. Credited as one of the first discoveries made using airborne geophysics, the Keevil Group had recently found the small but very high-grade copper deposits at Temagami, Ontario. These developments in eastern Canada formed a foundation for remarkable growth and Teck's present status as one of Canada's most successful and respected mining companies.Teck currently operates successful mining ventures across Canada and has international exposure through its association with Cominco Ltd., M.I.M. Holdings Limited and Metallgesellschaft AG. Operations in eastern Canada, however, remain an important component of Teck's ongoing success. The David Bell and Williams mines at Hernlo, Ontario, are Canada's lowest cost and largest gold operations, respectively. The Niobec Mine at Chicoutimi, Quebec, is North America's only significant producer of niobium. Teck maintains a 45070 interest in Golden Knight Resources Inc., part owner of the successful gold mining operation in the Casa Berardi area of northwestern Quebec. As a significant shareholder in Aur Resources Inc. and as a part owner, Teck is participating in the development of the Louvicourt deposit, a major base metal discovery at Val d'Or, Quebec."

Jan 1, 1992

By A. Anderko, R. D. Springer, R. D. Young

A thermodynamic model has been developed for calculating phase equilibria and other properties of multicomponent electrolyte systems. The model has been designed to reproduce the properties of both aqueous and mixed-solvent electrolyte systems ranging from infinite dilution to solid saturation or pure solute limit. The model incorporates formulations for the excess Gibbs energy and standard-state properties coupled with an algorithm for detailed speciation calculations. The excess Gibbs energy model consists of a long-range interaction contribution represented by the Pitzer-Debye-Hiickel expression, a second virial coefficient-type term for specific ionic interactions and a short-range interaction term expressed by the UNIQUAC equation. The accuracy of the model has been demonstrated for common acids and bases and for multicomponent systems containing aluminum species in various environments.

Jan 1, 2005

By R. D. Corrans

"Abstract - Africa is endowed with a number of the world's giant ore deposits which have contributed significantly to the development of their host countries. Mineral exploration has a long history in the continent, but mining on an unprecedented scale took off during the latter part of the 19th century, accompanied by the development of lines of communication and other infrastructure to service the major mining centres .The ""Winds of Change"" which swept Africa in the 1950s and 1960s brought in new styles of government and economic management to a number of regions, often with demise of economic viability and infrastructure. ln recent years, with the end of the cold war, collapse of communism and changes in South Africa, new opportunities for mineral exploration are opening up rapidly in Africa. However, due to the large cost, long lead-in time, and high risk of developing new mineral ventures in the continent, it is necessary for the host countries to draft realistic and favorable mineral laws and fiscal codes in order to attract, and not deter, potential mineral investors.There will be an on-going role in mineral exploration throughout Africa for the artisanal miner, the smaller entrepreneurs and mining companies, exploration aid programs funded by the developed countries through African governments, as well as the major mining houses who have the resources to develop larger viable mineral deposits."

Jan 1, 1994

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By R A. Burwash

In the Yellowknife geologic province, 2,600-million-year-old granites are cut by three sets of diabase or gabbro dyke : (1) large dykes striking 70°E to E-W, (2) rare dykes striking N-S to 30°E and (3) an abundant swarm striking N 10°-300W. Preliminary potassium-argon dating has been carried out on whole-rock samples of the chilled margins and coarse centers of the dykes, and on mineral separates from the dykes and contact aureoles. Data from seventeen dated samples suggest that the dyke sets were intruded during three periods of basaltic magmatism -2,200, 1,500 and 1000 million years ago. The two earlier periods closely follow the time of emplacement of granites in the Yellowknife and Churchill geologic provinces. The latest diabase dykes occurring in the Yellowknife province are temporally related to a widespread basaltic magmatism, for which the term Keweenawan is not appropriate. D DRING the past ten years, methods of physical age determination have been widely applied to date the time of intrusion or metamorphism of Precambrian rock

Jan 1, 1963

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By Tweedy. D. H.

"The paper describes the rapid development of, and operational experience in the utilization of, pneumatic low-pressure pipeline hoisting systems to vertically convey raw coal and rock through shafts, supplementing shaft capacity-the greatest lift to date being 535 m.A typical installation has raised over 250,000 tonnes in less than one year from a depth of 413 m through a 350/ 400-mm pipeline at a rate of 85 tonnes per hour. Operational experience on seven systems has provided valuable data on performance and operating costs.The main advantages of the systems lie in the flexibility of the pipeline to occupy existing free space in shafts and underground roadways, the relatively low first cost, the short delivery and installation time, and the economical running cost.Conclusions are therefore reached on future applications for example, the use of boreholes in older mines where new production technology has outstripped shaft or slope capacity, inter-level hoisting to implement concentration on transport roads and perhaps full mine output from relatively small mines.IntroductionIt is seven years since the basic art and practice of the pneumatic hoisting of minerals was described. The technique was developed in Western Canada by Radmark Engineering and found favour in the United Kingdom with the National Coal Board. Engineering and commercial feasibility trails were conducted in collaboration with the Mining Department and Mining Research and Development Establishment of the N.C.B. There was also considerable involvement with the British Health and Safety Executive.During the last five years, rapid progress has been made in the installation of new systems in the United Kingdom, Hungary and other countries. The operational experience gained makes it possible to report ""in depth"" on these installations, which cover a wide range of different physical mining applications."

Jan 1, 1982