Search Documents

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

The introduction of large diameter drill holes and mass firings in underground metalliferous mines has led to an increase in the number of reported sulfide dust explosions in Australia and overseas. Adaptation of the coal mining technique of using limestone to inhibit or prevent dust explosions has not been entirely successful as the development and inhibition of a sulfide dust explosion is somewhat different from that of a coal dust explosion. Tests were carried out on two pyritic ore samples, sulfur contents of 41 and 36 per cent, in 8 and 20 litre explosion chambers to evaluate the effect of the addition of limestone on the maximum explosive pressures developed and rates of pressure rise. Significant values were obtained in both chambers with dusts containing 60 per cent ore and 40 per cent limestone. The percentages of limestone required to inhibit the pyritic dusts were considerably higher than those values generally accepted by the mining industry and the current methods used to inhibit sulfide dust explosions should be re-evaluated.

Jan 1, 1986

The late Carboniferous to early Permian Featherbed Volcanics cover an area of about 3000km near the western margin of the Hodgkinson Basin, in northeastern Queensland. The dominantly ignimbritic volcanic rocks are mostly confined to a single, composite, volcano-tectonic depression, but, along with the associated intrusive rocks, may be divided into two main groups: late Carboniferous I- type rocks and early Permian A-type rocks. Late Carboniferous I-type andesitic to rhyolitic ignimbrites and minor andesite lava crop out in the southeastern, southern, and southwestern parts of the complex, mostly confined to a basin-like depression, or "sag" structure, and are associated with coeval dioritic (and rare gabbroic) to granitic intrusive rocks. Extensive Sn, W and base- metal, and some Au, mineralisation are associated with these rocks, particularly in the southeast. The main part of the complex is of early Permian age, and consists almost entirely of A-type rhyolitic ignimbrite and relatively minor volumes of lava intruded by a peripheral ring dyke of porphyritic microgranite and by resurgent-type plutons of porphyritic microgranite and microgranodiorite. These rocks are associated with sparse base-metal, Au, U, W, and Sn mineralisation.

Jan 1, 1987

Scheduling the transformation of in situ coal to run of mine coal and its subsequent beneficiation to a saleable product involves the use of many `parameters' or `adjustment factors'. These include in situ density, moisture adjustments, mining

Jan 1, 1998

The Antarctic Peninsula consists of accretion complex sedimentary and volcanic rocks, talc-alkaline magmatic are rocks, marginal basin sediments and extension-related alkali basalts, dominantly of Mesozoic to Cenozoic age. Metallic minerals have been recorded at "250 localities but two thirds of these are innocuous occurrences of Fe+Cu accessory minerals. The remaining -70 localities are related to hydrothermal mineralization processes. Metallogenetic associations identified are: vein and breccia-hosted Fe+Cu+Zn+Pb+Mo or Fe+Cu+Mo+Mn, shear-hosted Fe+Cu, volcanogenic Fe+Cu and pegmatite-hosted Fe+Cu+Mo+Mn. Anomalous Au, Ag, As, W and Sb also occur but are not of economic interest. Metallogenic zoning is unproven and genetic models are uncertain, possibly involving volcanogenic, epithermal to hypothermal vein and porphyry-type systems. Substantial field and laboratory studies are required to understand distribution and Genesis.

Jan 1, 1987

The treatment plant of the Gold Mines of Kalgoorlie Ltd. is situated on the Oroya South Lease, on the Eastern edge of the Kalgoorlie Golden Mile.It was designed and erected by Messrs. Alex. Stewart and Company, in consultation with Mr. Harry Hey, and was completed in November, 1937.Its original capacity was 9,000 tons of all-sulphide ore per calendar month, l?ut the plant was extended in October, 1939, to treat 13,000 to 14,000 tons per month of mixed sulphide and oxidised ore.Recovery of the gold is accomplished by cyanide treatment, followed by flotation of the cyanided residue, roasting and cyanidation of flotation concentrate and precipitation of the gold from the cyanide solutions. In the cyanide section, the crushed ore is finely ground in cyanide ,solution and the pulp is agitated to dissolve further gold. It is then thickened and filtered. In the flotation section, this filter residue is conditioned with S02 gas and a pyrite-gold concentrate recovered by flotation.This concentrate is roasted and then cyanided.KALGOORLIE ORE DEPOSIT.The Kalgoorlie ore deposit occurs within a wide area of Pre-Cambrian rocks, ,and consists essentially of two series of basic igneous rocks known as the older greenstone series (calc schist) and the younger greenstone series (quartzdolerite- greenstone) . The older greenstone is a group of lava flows. The younger intrusive greenstone series can, in the main, be classified as a chloritised and carbonated...

Jan 1, 1948

By Thimons E. D, Derick R. L

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high-expansion foam. As a result of several strategic decisions, the fire appeared to be held in-check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed.

Jan 1, 1988

By Vassiliev P

Cut-off optimisation, based on the work of Lane (1988), can be used to maximise the NPV (Net Present Value) of a mine by the judicious manipulation of cut-offs and the use of stockpiles. Apart from maximising NPV, cut-off optimisation will ver

Jan 1, 1998

By Tarrant GC

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By W Gale

Rock and coal fractures together with micro seismic vibration is a common occurrence during mining, however, it is very uncommon for coal and rock to be propelled into the roadway. Irrespective, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy which can contribute to the propulsion of coal from the face or ribs are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area. The aim of this presentation is to briefly review the mechanics of a coal burst and to discuss the mining situations for which the energy is sufficient to create bursts. A brief discussion of alleviation strategies is discussed. This is an abstract only. No full paper was prepared for this presentation. CITATION:Gale, W, 2018. An overview of coal burst phenomena, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), p 2 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By Smart RST C, Johnson NW, Ralston J, Griffin LF

At the Copper Concentrator of Mount Isa Mines, the largest diluent of the copper concentrate is liberated fine pyrite. Laboratory flotation tests carried out as a function of grind and flotation Eh in combination with surface analysis by X-ray photoelectron spectroscopy (XPS) have identified the major mechanisms of iron sulphide flotation. It was found that a significant proportion of the iron sulphide minerals had surface coverages of graphitic carbon, sufficient to impart moderate hydrophobicity in the absence of collector. A smaller, but economically significant proportion of chalcopyrite was also affected by the graphitic carbon coating. Two methods were tested to reduce the impact of the natural floatability of the iron sulphides on concentrate grades. 1. Depression through the use of organic depressants. 2. Preflotation to remove the "naturally hydrophobic" iron sulphides (flotation independant of Eh ) prior to chalcopyrite flotation. Preflotation was tested at the pilot plant scale. It was found that the amount of chalcopyrite reporting to the preflotation rougher concentrate could be minimised through flotation at a mildly reducing Eh by the use of nitrogen as the flotation gas to maintain the low Eh conditions resulting from grinding. The preflotation rougher concentrate was upgraded to an iron sulphide concentrate or a low grade copper concentrate.

Jan 1, 1991

By Bisshop J. P W

Maximum recovery of sulphide minerals by flotation is achieved over a limited size range. Valuable particles above and below this range have a smaller probability of being recovered. In the normal grinding-flotation operation, not all valuables are reduced to the optimum size range, and therefore sub- stantial losses occur. A significant improve- ment in the size distribution is not usually possible within the conventional circuit, and a more complex arrangement may be necessary to obtain optimum recovery of the valuable mineral. This problem is considered with refer- ence to the Mt. LyeZl concentrator. The performance of the existing circuit is dis- cussed, and it is shown that losses in recovery occur in both coarse and fine sizes. Laboratory tests indicate that regrinding the coarse particles results in an increase in recovery of up to 4%. Redistribution of plant grinding capacity to reduce initial grinding power by 6% and use this capacity to regrind coarse particles was considered. It is con- cluded that overall plant efficiency would be increased by 2% provided that overloading of the regrind mill could be avoided.

Jan 1, 1977

The evaluation programme and procedures develop- ed for Saindak porphyry copper-gold-silver- molybdenum deposits located in an isolated area in an extremely and region of Baluchistan are described in detail. Due to its isol .ted location, far removed from supply centres, harsh climate, paucity of water and non-availability of even unskilled labour, Saindak presented problems for which no ready made solution exist- ed. It is hoped that this Paper may be of some value to those in the LDCs who may wish to undertake similar ventures.

Jan 1, 1988

There is considerable variability in the level of detail incorporated in prefeasibility studies relating to mining developments. Hence, when undertaking a review or audit, it is critical to attempt to ascertain at an early juncture precisely who has compiled the various facets of the study, for what purpose it was intended and the terms of reference given to the authors. Likewise, when commissioned to undertake an audit it is preferable to have proper terms of reference and to be aware of the purpose to which the audit will be put.These factors will influence the degree of detail an auditor would expect to find in the study and consequently, the degree of effort/time required for the audit process. In most instances audits do not imply recalculation of the entire study or modifying it in anyway, but involve an overall assessment of the methodology used, combined with spot checking of detail. One of the most difficult aspects is to determine a realistic order of accuracy for the overall study when the accuracy of the individual components may differ markedly.

Jan 1, 1990

The Kundana underground narrow vein gold mine had a recent history of large and damaging seismic events. Following a period of seismic events on 30 July 2001, in which nine miners were temporarily entrapped at depth due to falls of ground in several parts of the decline, the mine operation was required to develop a seismic management system to mitigate seismic risk to the operation. A micro seismic systems and boundary element modelling of mine sequence highlighted large-scale footwall faults and the mining of gold bearing shear veins to be focal structures for seismic energy release between depths of 300 m to the base of mining at 650 m. The integration of seismic data, identification of geological structures and mapping of zones of failed rockmass led to the successful generation of a non linear boundary element model and a seismic hazard strategy. This enabled mine sequences to be assessed daily, monthly and periodically for potential seismic hazards and therefore assigned both economic and personnel risks for the recovery of the ore reserve at the Kundana Underground Operation.

Jan 1, 2005

Design and construction techniques used to develop two highway tunnels in inaccessible mountainous terrain are described. Measures used to adapt the design to the unusual geology and topography are discussed, as well as measures to adapt the construction methods to available equipment, materials, and skills. Sharp local variations in geoloqic conditions resulted in field modifications to both design and construction techniques. The geology is a volcanic ash and breccia-agglomerate at one site, a jointed andesite at the other, which is also the site of a major landslide. Both rock reinforcement in the form of pretensioned and grouted rock bolts with a shotcrete lining,and rock support by struc- tural steel sets with a reinforced concrete lining were used. A canyonside location and high lateral in-situ stresses required modification of design procedures. Pilot tunnels at both sites resulted in adapting the designs to site conditions with large savings in lining costs, disclosing problem areas in advance of the main excavation, and cushioning of blasting pressure to minimize stability problems.

Jan 1, 1976

In recent years rehabilitation of mine sites has become a principal focus of mining legislation in Victoria. In previous eras, managed rehabilitation commenced, if at all, towards the end of mining operations. Planning for rehabilitation works now commences before an exploration licence is granted.The paper gives a brief overview of the requirements for rehabilitation under the Mineral Resources Development Act 1990, Extractive Industries Act 1966, and related environmental planning legislation including rehabilitation bonds and enforcement provisions.A brief review of the current taxation provisions is also included.

Jan 1, 1992