Search Documents

The five main ways in which coal is used are1. for electricity generation,2. as a lump fuel for domestic and industrial purposes,3. for gas making,4. for making carbon for chemical and metallurgicalindustry, and5. as a source of coal tar and coal-tar chemicals.In the past about 80 per cent of Victoria's brown coal has been used for power generation and the rest for making a lump fuel, in the form of briquettes. Some of these briquettes have been used for gas making, and a carbon industry based on them has recently been commenced, and could expand rapidly. However the enormous increases expected in power requirements, approximately a doubling every 10 years, will ensure that even if the manufacture of carbon increases dramatically and a large amount of coal is used for other purposes, the brown coal industry will always be dominated by power generation. As new fuels such as natural gas, oil, and nuclear fuel become available at competitive prices these will take their share of the power generation load.Natural gas or oil, or possibly pumped storage hydro, will almost certainly be used for all future peak-load stations, comprising around 40 per cent of the total installed generating capacity, but new base load stations will continue to be designed for brown coal operation until about the mid-1980s, by which time nuclear power stations will become competitive. By this time Victoria will have installed about 6000 MW capacity of brown coal stations, burning around 50 million tons/year of coal, compared with 18 million tons/year at present, with perhaps 15 million tons/year being used for other purposes.This consumption of 65 million tons/year should then remain fairly stable over the life of the power stations installed, well into the 21st century. Brown coal therefore appears to have an assured place in providinga major part of Victoria's fuel requirements, despite the diversification in fuel usage pattern which appears certain to occur with the recent developments in new fuel resources.

Jan 1, 1971

By C Linklater, J Chapman, A Watson

Closure options under consideration at some sites include backfilling mined-out pits with waste rock. Backfill may include mineralised and non-mineralised waste rock. Following groundwater rebound, flow-through conditions may develop in the pit post-closure. The backfill located in the saturated zone below the water table may release solutes under such conditions. It is therefore important to understand the potential impacts that backfilled pits could have on postclosure groundwater quality.Geochemical characterisation programs are the foundation for assessing the potential chemistry of water that has contacted mined wastes. Such programs must be designed to obtain data relevant to the closure options under consideration. To complement standard testing techniques, SRK utilises saturated column testing designed to generate data on leaching rates under anoxic conditions that could be encountered within submerged backfill.This paper presents the findings of saturated column test work carried out on waste rock samples from an iron ore mine in the Pilbara.CITATION:Watson, A, Linklater, C and Chapman, J, 2016. Backfilled pits – laboratory-scale tests for assessing impacts on groundwater quality, in Proceedings Life-of-Mine 2016 Conference , pp 110–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

A failure criterion for coal is proposed in which a distinction is made between brittle and "pseudo-ductile" failure. This criterion is then used in the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition, equations are obtained which allow the äritical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure". The use of these formulae is then demonstrated by comparing the results with pillar case histories derived from the literature.

Jan 1, 1986

By Wenya X, Bingchen C

About 60 per cent of magnesite ores of Haicheng Magnesium Mine, due to their low grade, are not currently commercially exploitable. In this paper, the flotabilities of the main component minerals of the ores were studied in detail with ether amine as collector. Based on. these, a new technique of reverse-direct flotation with single etheramine as collector for the beneficiation of the ores was developed. It gave highly satisfactory results. On the basis of the calculation by means of CNDO/2 method, of the studies of the solution chemistry of magnesite and of the adsorption tests and Zeta-potential measurements, the key mechanism in the new technique about activating effect of Ca2+ on the flotation of magnesite was suggested.

Jan 1, 1993

By X Z. Sun, N Jiang, J H. Zhao, C X. Wang, L Y. Bai

In backfill grouting for underground coalmines, the filling materials strengthen the caving rock and support the overlying strata to reduce surface subsidence. The broken roof strata fail and collapse during mining operations without appropriate supporting measures being taken. It is difficult to perform continuous backfill mining on the working face of such roofs using the existing mining technology. Therefore, in order to solve the above problems, fly ash and mine water are considered as filling materials, and flow characteristics of fly-ash slurry are investigated through laboratory experiments and theoretical analyses. Laws governing the diffusion of fly-ash slurry in the void of caving rock masses and in the void between a caving rock mass and a basic roof are obtained and verified. Based on the results obtained from the above analyses and field conditions at the Zhaoguan coalmine, Shandong Province, China, a cave backfill grouting system of the hauling pipeline is developed and successfully tested at the 1703 working face. The results demonstrate that a filling rate of 43.46 per cent is achieved, and the surface subsidence coefficient of the grouting process is found to be 0.475. Compared to the total caving method, the proposed system is found to achieve a reduction rate of 40.63 per cent. This effectively helps in lowering the value of the surface subsidence coefficient. Fly ash and mine water, considered as primary materials in this study, also play a significant role in improving the air quality and water environment.

Nov 29, 2022

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

By D Bush, F Goddard

The electrification of Australian mine sites will see a boom in the use of batteries of all chemistries. Lead acid batteries, a traditional mainstay of the mining industry, are expected to nearly double by 2030, however their use will be eclipsed by the explosive growth in lithium batteries. By 2030 the lithium battery market is forecast to be nearly four times the size of the lead acid battery market. Unfortunately, this will result in a corresponding avalanche of waste batteries to be disposed of. Barely a day goes by without battery generated fires being reported in the media and they have become an increasing nightmare for waste management companies and waste facilities. The safe recycling of batteries will also become increasingly important for mine sites to achieve their sustainability goals and reduce their environmental footprint. What are the risks posed by waste batteries, what are the regulatory requirements and how can you manage or eliminate these risks? What current practises does your mine site currently have for the safe management and disposal of batteries from your site? How prepared are you for the coming avalanche of waste batteries?

Apr 16, 2024

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm', and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine's variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

By Warren M

Many Australian tunnelling and mining companies regularly investigate different methods or equipment in an attempt to keep ahead of their competition. Sometimes the result is a new approach or process which wins a tender or provides an advanced solution to a problem.The Australian Government has a policy of encouraging forward thinking among Australian companies and provides a range of incentives. One of these incentives is currently available retrospectively to 1985 - 86, and the registration process is relatively simple with only one form to be completed. Companies who investigate methods of raising productivity could be reimbursed for the costs of the investigation.

Jan 1, 1993

By K Nguyen

The advances in computerised processors and digital microscopic imaging have enabled more studies that attempt to quantify textural information from rock images. However, a texture classification system designed for geometallurgy has always been challenging, as it combines general image analysis techniques and specific texture classifications in terms of the size, shape and orientation of mineral particles. In this paper, a novel texture analysis technique using grey level radial shell association (GLRSA) and spectral angle mapper (SAM) to discriminate between different geological images is outlined. The technique can be applied in routine analysis and characterisation of mineralogical and textural attributes which may correlate with variability in mineral processing behaviours. Using this texture analysis technique, a set of small texture reference images, a texturelet reference library, has been identified from a suite of drill core images. Rock types are classified according to the proportion of each texturelet type recognised. The library is site specific.CITATION:Nguyen, K, 2013. A new texture analysis technique for geometallurgy, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Electricity Commission of New South Wales operates three power stations located on Lake Macquarie and Lake Munmorah. Coal for these power stations is supplied by three collieries operated by the Electricity Commission, three operated by the State Mines Control Authorityrand one privately owned. Most of the coal used in these power stations is won from the Great Northern seam which lies at depths of up to 220 ft at Awaba and at depths of the order of 600 ft at the remaining mines on the southern end of the field.

Jan 1, 1972

By Brown K, Francis D

The Yallourn Open Cut Mine has recently commenced mining operations in the new East Field which will supply the 1450MW Yallourn W Power Station for the rest of its 30 year design life. The authors describe the design and implementation process followed during the rehabilitation of the areas disturbed by works associated with mining in the East Field. One area of the East Field, the old external overburden dump, has been of particular interest and is discussed in detail. A discussion on the fire protection considerations is included as these are critical and often misunderstood as being contrary to good rehabilitation design practice. Finally, the development of a master plan for the rehabilitation of the Yallourn Open Cut in general, incorporating the East Field work, is discussed.

Jan 1, 1992

By Manlapig EV, Davis JJ

A methodology for modelling dense medium cyclones is presented for cyclones operating under conditions which avoid particle interference or apex crowding. Particle interference and apex crowding are shown to result in less efficient separations and represent undesirable regimes of dense medium cyclone operation. In order to avoid apex crowding, suitable medium to ore ratios and apex diameters should be used. Cyclone density differentials should be kept below approximately 400kg.m 3 to limit loss of efficiency due to excessive particle recirculation within the cyclone. The relationship between size-by-size partition curves shows that the flow split and density of the medium within a cyclone can be related to two new parameters, the pivot partition number and pivot density. The parameters are common to each partition curve in any set of size-by-size data and are mathematically related to the familiar performance characteristics, ecart probable (Ep) and separation density. The resulting expression confirms that the Ep and separation density are directly related.

Jan 1, 1986

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

By S Vianna

Mineralogical information obtained from plant surveys is subject to errors, both due to sampling and experiment. To reduce these errors, and to ensure that information is consistent, a data reconciliation model has been developed for mineralogical data. Its capability includes mass balancing size data, total assays, assays within size-classes and liberation data. Unlike any other mass balance package, this package also allows reconciliation of the complex mineralogical information. For example, particles cannot simply be treated as binary, but consist of combinations of many minerals. Hence the distribution of mineralogical information is multidimensional and the mineralogical distributions are referred to as multiphase. In this paper, the different levels of mass balancing are explained, including how to mass balance liberation data. Furthermore a new technique based on probability theory can be used to infer distributions even when there is insufficient information to perform a mass balance, and this technique is also explained. Results for various stages are given.

Jan 1, 2002

The topic for my address is Sharemarket Floats - Issues for Expert Valuers. I've decided to focus on three areas where current practice in the preparation of prospectus valuation reports for resource companies might be improved. My central theme is that the valuer for a float should augment the usual assessments of the value of the company or its assets, with some input on the way the share market might value the company's shares when they are listed. I will then look at the valuer's role in relation to vendor consideration, last I will look at his role in providing investors with some input on the risk dimensions of the new company.

Jan 1, 1989

Geologists often classify ore textures on the basis of the origin of the rock in which they form and the grade of one or more minerals within the ore (Sinclair and Blackwell, 2002, pp 32-36).  Metallurgists, on the other hand, need to know how best to process the ore in order to extract the valuable minerals from it (Petruk, 2000). Geological classification has the following disadvantages:it requires the services of skilled economic geologists, of whom the supply has been dwindling for many years;it is subjective, depending on the perceptions of the individual geologists who make the classification; andit may relate only weakly to processing requirements of the ore. We describe methodology for automatic classification of ore textures from images of drill core. The images analysed are æclassifiedÆ images, in which a particular mineral (or mineral group) is assigned to each pixel. The new methodology is intended to:provide a quantitative and reproducible alternative to traditional geological texture classification,relate to process mineralogy of the ore, andimprove the ore-texture-related input to orebody domaining and geostatistical block models.

Jan 1, 2008