Search Documents

By D Espinoza, I Rees, J Pocoe, P Collier

P Collier, I Rees, J Pocoe and D Espinoza

Mar 22, 2022

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By N Setoudeh, A Nosrati, N J. Welham

The current surge of interest in lithium (Li) is due to the anticipated demand for electric vehicles and small scale power storage. Brine deposits contain most of the global Li resource, however hard rock deposits can be more readily and rapidly developed and comprise the majority of proposed projects. These projects plan to use the conventional processing routes of dense medium separation and / or flotation to produce a spodumene concentrate for sale. The standard route for subsequent processing of spodumene concentrate is thermal decrepitation, acid leaching, solution purification and precipitation of lithium carbonate. This is typically followed by further purification. A number of projects have ores which contain other lithium minerals, principally micas, lepidolite and zinnwaldite, necessitating an alternative treatment route. Several different routes for spodumene processing are under development to reduce costs to compete with brine projects. This paper will give an overview of the strengths and weaknesses of the current and alternative processes.CITATION:Welham, N J, Nosrati, A and Setoudeh, N, 2017. Lithium ore processing – an overview of the current and new processes, in Proceedings MetPlant 2017, pp 185–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By P Bartsch

Uranium solvent extraction, USX has been applied commercially for recovery and concentration for over 50 years. Uranium in acidic liquor, which is prepared following ore leaching, solid/liquid separation and clarification, can be treated through a sequence of operations; extraction-scrubbing-stripping, to obtain purified liquor. USX has dominated the primary uranium industry as the preferred technological route to converter grade yellowcake. The practices of design and operation of USX facilities has found renewed interest as new mines are developed following decades of industry dormancy. This article seeks to outline principles of design and operation from the practitioner’s perspective. The discussion also reviews historical developments of USX applications and highlights recent innovations. This review is hoped to provide guidance for technical personnel who wish to learn more about good practices that leads to reliable USX performance.

Aug 8, 2011

By K Fiedler, A Newell, P D. Munro

Test work is the foundation upon which the success of projects and subsequent operations is laid, reflected in Professor Arthur Taggart’s pithy observation: ‘Make your mistakes on the small scale and your profits on the larger scale’. Indeed, Professor AllanTrench has succinctly noted that ‘Get the metallurgical characteristics wrong and you don’t have a project’.With deposits becoming lower grade, more structurally and mineralogically complex, final products requiring lower levels of impurities and tailings management demanding more attention, test work now assumes even greater significance in the acceptance and successful execution of a project. This paper is the first in a series aiming to stimulate thought on the metallurgical test work process by getting back to the fundamental basics through exploring and providing some guidelines for the metallurgical testing world, noting preferred practices as well as precautions and mitigations. This covers the key characteristics of metallurgical test work programs, including what needs to be done, sample selection, quality control and associated drivers, and most importantly, selecting, assessing and managing test work facilities. CITATION:Newell, A, Munro, P D and Fiedler, K, 2018. Metallurgical test work – between a rock and a hard place, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 15–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Development of the Davcra flotation cell has continued over the past seven years. Preliminary testwork on single cells has now been extended to a com- plete Davcra flotation circuit, to cells ranging from 5 to 400 tons per hour capacity and to cells operating on a variety of materials. Operation of both test and production units has shown the Davcra cell to be competitive with conventional flotation machines. It offers a lower capital cost installation than conventional cells and in addition has a number of. operating advantages, particularly in its adaptability to automatic control.'

Jan 1, 1971

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

By F I. Cox, D Peeler, T Bodisco

"Diesel particulate matter (DPM), in particular, has been likened in a somewhat inflammatory manner to be the ‘next asbestos’.From the business change perspective, there are three areas holding the industry back from fully engaging with the issue:There is no real feedback loop in any operational sense to assess the impact of investment or application of controls to manage diesel emissions.DPM are getting ever smaller and more numerous, but there is no practical way of measuring them to regulate them in the field. Mass, the current basis of regulation, is becoming less and less relevant.Diesel emissions management is generally wholly viewed as a cost, yet there are significant areas of benefit available from good management.This paper discusses a feedback approach to address these three areas to move the industry forward. The six main areas of benefit from providing a feedback loop by continuously monitoring diesel emissions have been identified: Condition-based maintenance. Emissions change instantaneously if engine condition changes. Operator performance. An operator can use a lot more fuel for little incremental work output through poor technique or discipline. Vehicle utilisation. Operating hours achieved and ratios of idling to under power affect the proportion of emissions produced with no economic value. Fuel efficiency. This allows visibility into other contributing configuration and environmental factors for the vehicle. Emission rates. This allows scope to directly address the required ratio of ventilation to diesel emissions. Total carbon emissions. For National Greenhouse Emissions Reporting (NGER)-type reporting requirements, calculating the emissions individually from each vehicle rather than just reporting on fuel delivered to a site.CITATION:Cox, F I, Bodisco, T and Peeler, D, 2014. Continuous remote emissions monitoring – the lynchpin for air quality management, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

At the outset, I guess we should define what we mean by "com- modities". In the 20 minutes or so which I have for this paper, it is impossible to tackle all commodities -one would need to con- sider not only the base metals but also the ferrous iron and steel products as well as energy commodities such as coal, oil and even uranium. For the purpose of this address however, I would prefer to refer to the principal non-ferrous commodities: copper, lead, zinc, aluminium and nickel and, I would like to consider some of the changes which have taken place in the industry over the past 20 years-and the likely reasons for these changes. I would also like to dwell a little on the future and some of the key issues which-may influence the future path and direction of the metals industry.

Jan 1, 1988

By P Holtham, W Valery, P Baguley, A Jankovic

There is a growing interest in magnetite ores because of the increasing demand for this commodity. With these ores, there is significant cost associated with milling the ore to fine sizes using ball mills in closed circuit with hydrocyclones. Cyclone classification efficiency tends to be poor due to the large difference in density between magnetite and gangue. This decreases the grinding circuit efficiency and results in over-grinding of magnetite. The objective of the work described in this paper was to modify the Bond locked cycle milling test procedure to quantify the loss of grinding circuit efficiency due to the mineral density effect. The locked cycle test procedure described here includes a stage of magnetic separation treating the closing screen undersize, which allows simulation of magnetite classification. The effect of classifier efficiency on low-density particles (non-magnetics) was simulated by altering the proportion of closing screen undersize bypass returning to the mill. Using a magnetic separator and a screen in the magnetics stream, different proportions of the magnetic fraction can be bypassed, thus allowing simulation of the effect of particle density on classification efficiency. This laboratory test work has confirmed that the impact of mineral density on cyclone efficiency subsequently has a crucial negative effect on ball mill circuit capacity. The results are in good agreement with reductions in capacity observed in practice. Multicomponent grinding and classification models were also developed in the LIMN software environment and were able to successfully simulate both the industrial and the laboratory ball mill circuit. The test and modelling procedures established in this project could be used for improved design of new magnetite ball mill grinding circuits as well as the optimisation of existing circuits.CITATION:Jankovic, A, Baguley, P, Valery, W and Holtham, P, 2015. Effect of mineral density for milling magnetite ores, in Proceedings Iron Ore 2015, pp 159–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

To solve the mining safety and health needs of the future, access to, and sharing of, timely and relevant information will be crucial. The next generation of the Web will provide tools (RDF, OWL, SPARQL, etc) to define and link content for more effective discovery, integration, and reuse across applications and organisations. A recent Gartner Research Report (Finding and exploiting value in Semantic Web technologies on the web, May 2007) predicts these technologies will begin to coalesce in ten years. Implementing this Semantic Web requires structured web content described via metadata (information about information). If an industry or enterprise bases its metadata on a common vocabulary, it becomes possible to share and reuse information. The National Institute for Occupational Safety and HealthÆs (NIOSH) Mining web site provides access to more than 1500 NIOSH-developed publications, products, and topic pages on issues as diverse as ground control, respiratory diseases, and mine emergency management. As the site has grown, locating content has become increasingly difficult. To improve the searching process, a panel of internal experts representing all major research programs was established to develop a controlled vocabulary for indexing that content. The outcome is the NIOSH Mining Safety and Health Thesaurus, a faceted, hierarchical thesaurus containing hundreds of mining safety and health terms organised into 20 facets (eg diseases, injuries and disorders; hazardous events and exposures, equipment, engineering and administrative controls). One immediate goal of this project is to reduce the complexity of locating information on the NIOSH Mining web site by implementing metadata and faceted information retrieval techniques. Another goal is to stimulate discussion in the international mining community regarding developing metadata standards so the industry is ready to adopt future Semantic Web technologies to improve access to mining safety and health information.

Jan 1, 2008

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By R Valenta, J Owen, D Kemp, E Lebre, G Corder, J Thomas

Numerous recent analyses have shown that future demand for a broad range of critical commodities is unlikely to be met by new discoveries and recycling alone. The only practical alternative source to address this shortfall comes from orebodies which are currently either uneconomic or inaccessible. A common assumption is that a simple rise in commodity price will render these deposits economic. The mining industry has a long history of innovation allowing economic production from increasingly low grade and technically challenging orebodies. Industry “roadmaps” have been produced on a regular basis, with the aim of identifying future innovations which will allow this progression to continue. At the same time, there have been relatively few systematic analyses of the actual range of challenges facing undeveloped orebodies. The aim of this study is to analyse the mix of challenges faced by a group of undeveloped orebodies in order to better understand the relative importance and necessity of innovations applicable to the deposits, with the ultimate aim of determining the relative value and impact of possible innovations to the economic viability of those deposits. CITATION: Valenta, R, Lebre, E, Kemp, D, Owen, J, Corder, G and Thomas, J, 2018. Can a simple price-rise unlock complex copper orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 71–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By W Stange, N Hanson

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction û primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007

By J King, T Hunter, R Coleman

"The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.Trends amongst service providers will be put forward as well as developing options and alternatives. These embrace a whole gamut of agile alternatives in the areas of partnering, alliances, commercial and shared risk models and mutual innovations. These will be discussed with some case studies and suggested approaches.Particular emphasis will be upon brownfield expansions and upgrades which have emerged recently as a preferred lower capital and focused way to achieve best practical outcome at lowest cost. There are a number of specific features of such brownfields projects including the requirement for very close cooperation between the execution team, operators, maintenance and suppliers and a maximum usage of site resources and ingenuity. Often, required investment hurdle rates are high, downtime allowed is minimal and site resources usage is maximised. This requires mutual trust, good planning and high health, safety, environment and community (HSEC) standards and practice. In many ways the practices and skills needed are the exact opposite of the historical ‘big greenfields’ project with which the industry has been geared for more recently.Another developing area has been with innovative commercial models and practices. These have been as a direct result of the more challenging investment criteria being adopted and the relative hunger of service providers. It has become more common to look at these commercial/costing alternatives very early in the project cycle as an essential project tool and not just as a possible option. These commercial solutions cover such alternatives as leasing and rental, deferred payments, build–own–operate–transfer (BOOT) and build–own–operate (BOO), whole-of-mine preferred spares and maintenance terms, and aggressive performance targets with real assurance penalties. Once again this requires very close mutual dealings and trust, and sufficient time allocation compared to a conventional approach.Citation:Coleman, R, King, J and Hunter, T, 2016. Upgrades, Modernisations and Expansions... Where Will the Expertise, Capability and Skills Come from in the Future?, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J Li, A McFarlane, J Yu, L L. Kuhar, R Meakin, N Chapman

"Column leach tests are used frequently to predict recoveries and reagent consumption for nickel laterite heap leaches. These column leaches often run for more than 100 days and therefore require long-term monitoring and data analysis to achieve the desired information. To minimise the cost and time required to obtain relevant information for nickel laterite heap leaching, we have developed a small-scale hydrogeometallurgical laboratory test to serve as a proxy to column, and by inference, heap leaching. In excess of 50 leach tests were conducted using four different small-scale proxy and column leach tests to compare predicted nickel recoveries, acid consumption and leach kinetics and to determine whether insight into potential scale-up effects can be obtained. The most promising proxy test was identified and we achieved a statistically significant recovery and acid consumption correlations between this test and the column leach tests. The accuracy of the small-scale tests was confirmed by column tests run on new laterite ores. This geometallurgical proxy could be of use for the population of block models and process selection during the mine planning phase or for optimisation and control during processing.CITATION:Li, J, Kuhar, L L, Meakin, R, Chapman, N, McFarlane, A and Yu, J, 2016. A Geometallurgical Proxy for Nickel Laterite Heap Leaching, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Flanagan, T Sua, B Wright, T Carroll, B Van Dijken

"BHP Billiton (BHPB) West Australian Iron Ore (WAIO) conducts an extensive geometallurgy (geomet) program for its iron ore deposits in the Pilbara. The geomet program provides accurate information to infrastructure engineers, resource geologists, mine planning engineers and the technical marketing team on the performance characteristics of iron ores. Performance metrics include production planning, such as lump/fine splits, processing capability such as the level of ultra-fine iron ore and ironmaking blast furnace properties including tumble index (TI) and reduction disintegration index (RDI). Prior to the introduction of the current geomet program in WAIO, basic geometallurgical information was provided at the deposit level, such as deposit lump percentage and head grade chemistry. As the business value of geometallurgy was realised during the growth period of WAIO, the geomet process was reviewed and formalised into five steps: geomet drill planning laboratory measurement data management algorithm development block estimation.The geomet laboratory process produces simulated iron ore products from drill core, which are then subjected to physical geometallurgy test work. With the large amount of geometallurgy data collected, extensive databases are utilised to collate and organise the data to improve its usability within the business. Algorithms are created from the data to predict important geomet variables and a block estimation method is used to estimate geometallurgical properties into resource models. The predicted geometallurgy data is regularly reviewed at the different steps against plant and shipping data to allow refinement of the geometallurgy algorithms. It is also recognised that geomet data can be used to optimise the operations in existing processing hubs for improved production rate. In addition, future geomet programs will focus on generating data from all available drill core programs, not just dedicated geomet drill holes, and will incorporate new types of data, such as hyper-spectral information, for improved geometallurgical estimation.CITATION:Wright, B, Carroll, T, Flanagan, M, Sua, T and Van Dijken, B, 2013. BHP Billiton West Australian iron ore geometallurgy - past, present and future, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 105-110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015