Search Documents

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By Jowett A

To compare open circuit lead primary rougher results at Mount Isa Mines Ltd., eleven surveys were made over five weeks of plant operation with varying ore sources, including a specially hauled sample of 100% Black Star ore. Three of the surveys which represented extremes in performance were selected for sizing, cyclosizing and assaying for lead, zinc and iron. A comparison of the flotation kinetics has revealed the similarities (including common problems) and differences for the surveyed ores. The concepts of entrainment and collectorless flotability are used to aid interpretation of the kinetic data.

Jan 1, 1978

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

The overall systems approach to blast furnace aerodynamics is explored including the time and spatial inter-relationships that exist between the furnace lines, tuyeres, burden characteristics, distributor capabilities and furnace operating practice. Attention is called to the time dependent, three dimensional aspects of blast furnace aerodynamics and to the existence of several zones within a furnace where the flow characteristics are different. Changes in furnace operating practice to take further advantage of fully beneficiated burdens including formed coke are discussed from a practical viewpoint. Lessons learned in a variety of shaft furnaces used for other purposes are discussed insofar as they have a bearing on aerodynamics in an iron blast furnace. Questions are raised about the penetration of hot blast in large furnaces. Operating practices and.proposed solutions are evaluated where tuyeres over iron and slag notches are restricted or plugged. Opportunities are presented for using on-line hierarchical computer systems with adaptive tuning algorithms to provide non-linear control of changing process conditions in real time. This will make it possible for the blast furnace operator to optimise a variety of interrelated paramaters, each with different response times. Potential increases in productivity, fuel savings and improved quality control are believed to be within reach.

Jan 1, 1975

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

A simulation of the fluid flow, minera- logical and chemical aspects of in situ leaching is being developed for application to the recovery of metals from unbroken, naturally jointed rock. The fluid flow aspect has been developed. The rock is assumed to have a double-fracture property. A major joint set is responsible for bulk flow of solution, while a minor joint set, intersecting with the major set, allows the solution to contact the reactive minerals. The two-dimensional fluid flow through the major joint set is analysed by a streamline model for a particular well pattern. The other important components of the model are described briefly.

Jan 1, 1984

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

This paper deals with innovative techniques that have enabled personal computers to be used on the mine site to define, develop and manage an ore body resource, while being aware of the consequences to the environment. The same set of personal computer tools that are used for resource estimation, once the province of expensive workstations, can also be used by geologists, mining engineers, surveyors and environmentalists, in managing the whole mining process, including production, grade control, monthly reconciliation and stockpile management through to tailings the management, mine rehabilitation and the due diligence process of mine closure.

Jan 1, 1996

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

Data logged on mineral beneficiation processes during normal operation are analysed using time series (correlation and spectral) methods to identify the dynamics of the processes for on-line computer control. Recursive least squares estimation techniques are used to identify parametric models for a cassiterite flotation circuit and a coal washery. Identification problems such as the determination of model order, process time delays and the 'contamination' of the data by process recycle streams (feedback) are discussed. Typical results are presented in which optimised models are identified from data logged during normal operation.

Jan 1, 1985

Attempt has been made to determine the nature of charge on activated carbon surface by studying the electro-kinetic properties of the carbon in the presence of cations, anions and aurocyanide solutions. The zeta-potential measurements were made in the presence of individual ions and also in combinations. The cations and anions chosen were those commonly associated with gold bearing ores in Kalgoorlie area. It was found that the iso-electric point of Norit Carbon was at pH 4.45; below this pH the charge was positive, while above, it was negative. In the absence of gold cyanide solutions and in the presence of individual cations the i.e.p. shifted to the alkaline range (pH 7.2-8.5) while in the presence of anions the i.e.p. was shifted to less than pH 3.5. In the presence of aurocyanide solutions, the iso-electric point was still in the acid region irrespective of whether anions or cations were present. The probable mechanism for such a behaviour has been attempted after measuring the specific conductivities of solutions before and after gold adsorption, by studies using the electron- probe-mirco-analyser, and S.E.M. on the carbon surface.

Jan 1, 1982

Woodlawn Mines began underground operations in 1986. At the time of going underground it was envisaged that there would be no 'contract' payment to the underground employees. This was a relatively unique step to make, especially as most major underground mines in Australia relied heavily on the contract system to motivate their workforce. (Obviously with varying degrees of success.) Woodlawn faced the task of motivating their employees through a multi-skilled system with a great emphasis on leadership and a genuine care for their employees. The 'proof of the pudding' is that Woodlawn has not lost any time over industrial issues since beginning underground operations in 1986. To achieve success in any operation the organisation must not only be advanced in its management principles but also be prepared to be innovative in the way it deals with physical problems, ie ground control, equipment selection and maintenance. Difficult ground conditions at Woodlawn have necessitated the deployment of two Cabolt Jumbos and the construction of cost-effective shotcrete systems. The shotcrete system now being built has been tested in a prototype form and is proving to be a safe and simple way to manage weak, low stress friable ground. Although the ground at Woodlawn has low stress component by virtue of the fact the ore can have a density of 4.5dm3, cable dowelling has become a necessity. The two cable dowel jumbos install high quality reinforced cables. The pressure of 'production' means that these machines must be consistently available for use and the training of maintenance personnel and operators ensures that a maximum of cable dowels can be installed over any given time span. In any modem mine ventilation is a primary concern and the major area of concern comes from the vehicles themselves. In our recent replacement for the standard 'Toro' loader, three engine options were considered. A relative newcomer to underground mining was accepted. The Detroit 60 series (DDEC) engine came with a great reputation and has lived up to this. The engine has an electronic management system that reduces particulates to a hardly visible minimum, provides great amounts of engine power and reduces fuel consumption by approximately 45 per cent. The operational benefits of such an engine are worth sharing through this conference.

Jan 1, 1995

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

By Sakurai F

Akita Zinc Refinery of Mitsubishi Metal Corporation (MMC) started operation in 1953 with a capacity of 560 tons of electrolytic zinc per month. Its capacity has been expanded gradually and reached 8,100 tons per month in 1973. However, present production level is about 6,500 tons per month due to the depressed zinc market. In 1963, newly developed sulphate roasting was incorporated for residue treatment. Since 1973, electric power from Ohnuma geothermal power station of MMC has been supplied in addition to hydroelectric power from Komata power station of MMC. At present, about 40% of power is supplied from our company's power station and the rest is from the power company. Recent customers' demands for zinc prod- ucts include various kinds of shape, weight and chemical composition of galvanizing zinc alloy. It is necessary for zinc producer not only to meet the requirements of customers but also to enhance the value of zinc product in order to expand the market of zinc.

Jan 1, 1987

By Corrans I. J

A wide variety of copper-bearing gold ores exist throughout the world which have yet to be processed economically for gold recovery. The copper minerals present in these ores can be many and varied and usually result in high cyanide consumptions and problematical levels of copper in leach solutions. The copper content is often assessed as being of nuisance value as the ores are generally of the grade or type which can support neither a copper project nor a straight gold project, due to the interference of copper. Many of these problematical gold-copper ores could possibly be processed economically for gold recovery using a novel ammoniacal cyanide leaching system which utilises a copper-ammonia-cyanide complex as an effective lixiviant for gold, yet limits copper dissolution and conserves cyanide. Results from recent testing have promoted a re-evaluation of the economics of treating some gold-copper ores. This paper describes the novel leaching process and discusses the conditions employed to treat a variety of gold-copper ores.

Jan 1, 1992

By M I. Pownceby, A Guiraud, S Purohit

Sticking and breakage of iron ore pellets during high temperature reduction can result in several operational challenges during shaft furnace ironmaking. With the shift to H2-based DRI processes and decreasing iron ore quality, this issue becomes more prominent. It is therefore important to understand how the iron ore chemistry and mineralogy affects the sticking and breakage of pellets inside the shaft furnace. This study provides a review of the mechanisms that lead to sticking and breakage of pellets inside the shaft furnace. The sticking index of pellets is related to the rate of metallic iron production as well as the precipitation morphology of product iron. Sticking of pellets is also enhanced by the formation of low-melting slag phases. The breakage of pellets inside the shaft furnace is often associated with the mechanical load of burden and pellet swelling, which is caused due to iron whisker or protruded iron formation. This paper investigates how the composition of iron ore, particularly the presence of different impurity oxides such as SiO2, Al2O3, MgO, CaO and alkali oxides in the pellets, influences the sticking and swelling indices. The effect of ore mineralogy on these adverse behaviours is also discussed.

Sep 18, 2023