Search Documents

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

By Collins DN, Hollick CT

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95% have been achieved and with coarse ores over 80%,in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing -is correspondingly reduced.

Jan 1, 1990

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996

The diverse nature of inadvertent mine fires does not lend them to general treatment. But evolving from the unfortunate fires over past years is a simple principle in dealing with all fires to bring combustion under control. Control, in brief, means that the products of combustion, themselves possibly still with fuel values, are not revitalised by addition of fresh air. There are problems with fire- fighting, especially with water, as this may lead to production of CO and H2. Panel ventilation upstream of the fire must be controlled to direct all air over the fire. Some advantages in fire fighting are found by the use of "sails". Early diagnosis of fires and early treatment are essential for safety of personnel and safeguarding and recovery of property. Preparedness extends to up to date documentation, but first hand knowledge also is invaluable to the diverse personnel gathered to fight a fire, and in the decision making Involved.

Jan 1, 1981

By Misra V. N, Spottiswood D. J

In recent years the column flotation process has gained worldwide acceptance for processing various types of minerals under different circuit configurations. In an age when real prices of many mineral commodities are in decline and mining and labour costs are rising in real terms, it is more important than ever that concentration processes be not only efficient but also cost-effective. The column flotation process can give better metallurgical performance as well as involve lower capital and operating costs compared to conventional mechanical cells.This paper reviews the literature on columns and the effects of various column parameters on performance of the column flotation process. The history and principles of operation of the column flotation process are briefly discussed by way of introduction.

Jan 1, 1995

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

By Hall J. S, Zuiderwyk M, Reid A. F

A prototype version of a computer controll- ed on-line scanning electron microscope image analyser, employing the real-time signals ob tamed by digital control of the electron beam has been used to obtain statistical quantificat lion of a wide range of mineral grain character istics, including composition, size distribut- ion, and degree of liberation. These propert lies have been determined for suites of whole particles of flotation concentrates, mounted without further preparation. The facility is also well adapted to the measurement of general Istereological parameters. The computer control software is based on an operating system which includes the device drivers and which is linked to FORTRAN programs [containing the procedural algorithms. The beam scanner provides a 4000 x 4000 point raster swept at a 10 Mhz rate in steps of 1 to 200 points and a set of up to 8 signal channels which respond to electron or energy dispersive X-ray signals to provide a digital attern.characterizing the sample composition. the beam is stepped at high speed until a part- 'cle or phase boundary is encountered; a longer well time is set if X-ray data is required. he digital scanner interrupts the computer

Jan 1, 1977

By Hamblyn S

Oakbridge, in combination with its joint venture partner, Nippon Steel of Japan, is expanding its Bulga underground and open cut mines to meet the growing demand for coal in the Asian market. Expansion works underway will see the Bulga underground mine become a world leader in underground productivity, the introduction of a high capacity dragline into the open cut mine (largest capacity dragline in NSW) as well as a major upgrade of the coal preparation plant (CPP) and coal handling facilities (CHF) to process the increased production. This paper describes the planning and implementation of this major expansion program and highlights the rationale behind some key aspects of the program.

Jan 1, 1995

Sublevel open stoping (S.L.O.S.) was introduced at Rosebery in 1972 in the wider ore blocks below 14 level, largely replacing cut and fill methods which had been in use up till that time. During 1973/74 the method produced 10% of primary stoping tonnes, and by 1981/82 it increased to 65%. Because of the increasing reliance placed on sublevel open stoping for primary stoping production, every effort was made in both planning and operating to: - maximise ore recovery and reduce dilution - increase productivity - reduce costs.

Jan 1, 1982

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By E M. Wightman, C L. Evans

A recent survey of mineral processors undertaken as part of the International Mineral Processing Council (IMPC) Education Commission identified mineralogy as one of the key skills required for mineral processors (the other key areas being comminution, flotation, physical separation, sampling and extractive metallurgy). Past experience in a number of operations has shown what can be achieved when the data outputs from mineralogical tools are coupled with people with the right skills who can transform the data into actionable information. This paper reviews what has been done successfully in plant operations over a period of more than four decades and gives examples of a range of applications with both long and short-term objectives. The examples demonstrate the usefulness of mineralogical data – both basic and complex – in optimising mineral processing operations, whether the data are applied in a simple analysis or in more complex modelling. Similarly, the examples show the range of options available for operations to access the mineralogy information they need – through in-house experts and equipment based in centralised technology centres, through on-site equipment and experts or through external laboratories and consultants.The examples from industry highlight the huge potential benefit of including mineralogy as an integral part of operational best practice and raise the question of why more operations do not utilise what should be readily available data. Successful application of mineralogical data requires skilled people to generate relevant data of the required quality, together with skilled people to interpret the data (this may be the same person). And, as in any project, corporate recognition of the value of this approach to best practice is required to ensure continuing support. With fewer university courses providing courses in process mineralogy to undergraduate mineral processing engineers and chemical engineers, there is an increasing lack of knowledge about what mineralogical information is needed, how to get the required data and, equally importantly, how to turn the data into useful information.CITATION:Evans, C L and Wightman, E M, 2018. Understanding minerals in mineral processing – the basics and beyond, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 363–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The South Junction deposit of St Barbara Mines Limited was discovered in 1989 by the geologists of Ross Atkins Mining.The deposit occurs in the lower part of the Gabanintha Formation of the Lukes Creek Group in the Mt Magnet -Meekatharra greenstone belt. Country rock is predominantly talc-chlorite schist. Gold mineralisation is associated with north-south shear zones, quartz-carbonate-fuchsite alteration of the ultramafic rocks and in particular close to deeply weathered quartz-albite porphyry. For a detailed description of the geology of the South Junction Deposit see Fiala (1992).

Jan 1, 1993

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

Discontinuities often have a very detrimental effect on the stability of mine highwall faces. The west wall of the Muja open cut is remarkable for the number and variety of discontinuity sets which occur over a relatively small area. To-date 14 separate structural domains have been identified over an area measuring approximately 560 m by 120 m.The structural domains have been grouped into four structural assemblages on the basis of their angular relationships to each other and to regional folding and faulting. The distribution of these structural assemblages appears to be erratic and no controlling factors have been identified to explain or predict them other than in the most generalised terms.

Jan 1, 1993