Search Documents

By Lean P. J

The present The Zinc ODrporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) tailing dam (Site C) is expected to reach its terminal capacity late in 1985. Planning and design of new facilities for disposal of tailing after 1985 which includes new tailing dams (Site D) commenced during 1980. This paper briefly describes planning guidelines and specifications, location considerations, environmental aspects, operating strategy, engineering specifications, envirormental aspects and scheduling of works.

Jan 1, 1983

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

The Sishen iron-ore-mine produces 3 pro= ducts with size gradings of 25 to 8 mm, 11 to 5 mm and 5 to 0,2 mm and has a product capacity of 20 Mtpa. Ore is produced at an average Fe content of 66,2 % Fe for the two coarser pro= ducts and an average of 65,3 % Fe for the fine ore product. Three stage crushing is practised to re= duce the run-of-mine ore to -90 mm after which it is screened into five different size frac= tions of which four are heavy media beneficiated in static baths and cyclones and the fifth frac= tion discarded to slimes dams. A final three stage crushing and screening process is employed to produce the final three Products which are homogenized by means of blen=ding systems nrinr to despatch.

Jan 1, 1987

By Dif A. E N, Abdalla MH

The effect of multiple tunnels /cavities on the stress and deformation field of the soil media was investigated by using a two dimen- sional plane strain boundary element model. The soil was considered as an elastic, isot- ropic and homogenous media. The interaction of two circular and parallel tunnels/cavities was investigated. Depth of burial, tunnel spacing and surface load width were the system variables considered. The results of this study indicated that the vertical displacements of the soil media increases by decreasing the distance between the adjacent openings, the interaction between the two tunnels/cavities can be neglected for K/D > 5, while the load width has a minor effect except in the dis- tance of D from the center line of the load and for a depth of 2D.

Jan 1, 1987

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

An assessment has been made of six reported methods for the determination of the swelling of iron ore pellets on reduction. The methods are discussed on the basis of apparatus requirements, reduction conditions, sample requirements, measurement of swelling and reproducibility. It is concluded that the CNRM, LKAB, and Lurgi methods are the most satisfactory which presently exist for determination of the swelling of industrially produced, iron ore pellets.

Jan 1, 1974

By K Tungpalan, E Wightman, M Edraki, E Manlapig, L Keeney

The depletion of easily mined high-grade ore bodies resulted in the industry having to exploit lower grade, complex resources (Albanese and McGagh, 2011; Darling, 2011; Randolph, 2011). The trend is now towards mining and processing of low-grade and complex ores (Darling, 2011; Yingling, 1990). Variable geological and mineralogical characteristics, and complex mineralogy and texture can result in large variations in metallurgical response and also cause challenges in processing. (Carson, 1995; Lorenzen and Barnard, 2011; Yingling, 1990). Variability and the complex nature of ores are fundamental sources of risk that often cause the greatest economic impact (Dusci et al., 2007; Williams and Richardson, 2004). Hence it is important to effectively characterise these types of ore bodies and assess their processing performance (ie recovery, grade). To enable this, there is a need for the following: (i) characterisation of geological, mineralogical and metallurgical variability in the ore body; (ii) effective selection of drill core with characteristics that represent the range of ores in the entire ore body. CITATION: Tungpalan, K, Manlapig, E, Keeney, L, Wightman, E and Edraki, M, 2018. A systematic approach of sample selection to predict processing performance of an ore body, in Proceedings Complex Orebodies Conference 2018, pp 67–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Boland

Polycrystalline diamond compacts (PDC) have been widely used as cutting elements in the drilling tools for the oil, gas, civil and mining industries because of their faster penetration rates and longer bit life. US Department of Energy reports that PDC bits account for more than one-third of the total footage drilled worldwide (US Department of Energy, 2004). However, non-thermally-stable diamond composites (NTSDC) have seldom been applied to geothermal drilling, since premature failures of such PDC cutters have been observed in hard rock formations. Several factors need to be considered to prevent premature failure of cutters and improve cutting performance when using PDC-based bits and other rock cutting tools. The first set of factors consists of the strength, density, stiffness, toughness and thermal resistance of the PDC and the rock. A second set relates to the complex behaviour of the bonding between the PDC cutter and the bit matrix, or the pick and the pick holder, which is vital in maintaining stable, reliable and durable adhesion of the cutters to their hubs. Finally, based on a better understanding of the cutting processes, the formulation of a predictive model would assist in further development of cutter design.

Jan 1, 2004

The Division of Minerals and Geochemistry in collaboration with three mineral exploration companies, Mawson Pacific Ltd, Ramsgate Resources Ltd and Tectonic Systems Pty Ltd commenced a two year research project to investigate the application of remote sensing techniques to exploration for mineral deposits in access of the Yilgarn Block in Western Australia. The project utilizes satellite data such as day and night imagery from the NOAA-AVHRR (National Oceanic and Atmospheric Administration - Advanced Very High Resolution Radiometer) satellite. The recent research with the imagery in the Kalgoorlie, Southern Cross and Mt Magnet regions has highlighted the advantages of the mid infra-red and the two thermal response channels of NOAA-AVHRR for geological investigations. These three channels have the spectral resolution to distinguish stratigraphic units and younger intrusive bodies, and to delineate fracture zones and shear zones associated with Proterozoic dykes. But most important is the capacity to distinguish thermal signatures from geological structure, near-surface outcrop and palaeochannels which have been covered by unconsolidated sediments. The research project applies remote sensing methods including enhanced satellite imagery optimised to the Western Australian environment. It encompasses data from both space and airborne monitoring platforms that have obsreved a significant spectral response for the classification of alteration zone lithologies. It includes the collection of multiseasonal data from areas of interest which is essential both for the understanding of thermal characteristics of important lithologies and for the extrapolation from field work investigation to potential exploration areas. No comprehensive investigation of this type has been carried out within the Yilgarn goldfields.

Jan 1, 1987

By Qi P. H

Gold dissolution can be achieved with a number of complexing ligands, all with varying degrees of stability. Processes based on the use of halogens have been known for many years. Beside providing the necessary complex- ing role, the halogens under the appropriate conditions are very effective oxidants for gold. Of the halogens, the gold iodide complexes are the most stable in aqueous solution. Iodine can establish the desired oxidation poten- tial for oxidizing gold, and unlike chlorine and bromine, the oxidizing potential of iodine is mild enough to avoid the oxidation of impurity constituents like metal sulfides. A series of experiments to investigate the fundamental electrochemistry of gold in different halide solutions was performed. Cyclic voltammograms of gold in the presence of 10-2 M chloride, bromide and iodide, respectively show that for a given potential the rate of oxidation is much faster in iodide solution than in either chloride or bromide. An overlay of linear sweep voltammograms for the anodic oxidation of gold in iodide and the cathodic reduction of iodine species on gold provides an effective method for examining the dissolution of gold in iodideftodine solution. The dissolution rates obtained from both electrochemical and actual leaching results are compared. Optimum leaching conditions are analyzed in terms of the iodide/iodine concentrations. Conceptual processes for the recovery of gold and iodide and the regeneration of iodine are discussed.

Jan 1, 1991

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

By Crawford G. R, Wold M. B

The application of the hydraulic fracturing technique to the measurement of in situ rock stress from underground excavation is discussed; including relevant theoretical considerations, equipmenl details, experimental technique and analysis procedures. Examples of the application of the technique at three Australian coal and metalliferous mining operations are given. The results obtained from these applications are compared with corresponding results obtained from overcoring tests conducted in close proximity at each site. Generally good correspondence in a wide variety of rock types is indicated. Experience gained with hydraulic fracturing at several underground mining sites has indicated it to be a quick, cost effective means of gaining an understanding of the in situ stress field in sufficient detail for many mine planning functions.

Jan 1, 1990

The main aim of the conference is to work towards improved useage of steelplant slags which have largely been considered waste mater- ials, This paper summarised investigations carried out on the suitability of air cooled blast furnace slag, blast furnace granulated slag and basic oxygen steelmaking slag as road base materials. All slag samples were obtained from the PortòKembla Works of Australian-Iron and Steel Pty Ltd. Since road making materials are increas- ingly being characterised by use of resilient moduli, the compressive strengths and resilient moduli were determined for road base of the following slags. 1 Air cooled crushed blast furnace slag 2 mixes of air cooled blast furnace slag, granulated slag, and lime 3 mixes of air cooled blast furnace slag,-granulated slag and basic oxygen steelmaking slag. Evaluation of a local dacite (dense medium grained igneous rock, classification rhyolite), generally considered an excellent road base course material, was carried out for use as a reference material.

Jan 1, 1979

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

By Hsiung SM, Jiang YM

The orientation and location of the hydraulic legs are two very important parameters for the design of shield supports in longwall mining. Studies have shown that leg orientations and locations of a support determine the magnitude, orientation and location of the resultant support resistance which in turn affects the efficiency of the support and the ability to prevent premature roof falls in the face area. Therefore, there is a need to determine the best combination of orientation and location of the hydraulic legs for each type of shield support under various geological conditions. This paper attempts to evaluate, first, the individual role of each parameter (orientation or location) and then to determine their integrating functions in terms of ground control employing finite element analysis. Three types of shield support (2-leg and 4-leg shields and 4-leg chock shield) with various combination of the parameters are simulated and their effects are discussed. The optimum design for each parameter for each support type under various geological conditions is also discussed and recommended.

Jan 1, 1988

By M D. Urbani

HiTec Energy Ltd has been conducting research since 1996 into novel process routes for the treatment of low-grade and waste manganese sources for the production of high value and high quality electrolytic manganese dioxide (EMD) for the alkaline battery market. HiTecÆs approach is to treat previously unsaleable manganese deposits and mine site tailings using a novel sulfur dioxide leach route, followed by purification and electrowinning to generate the sought-after EMD product by an environmentally superior processing route to those presently practiced throughout the world today.HiTec Energy Ltd expects to be in commercial production with its Stage 1 facility in Kalgoorlie in the last quarter of 2004 for the production of 12 500 tpa EMD. With this production facility being adjacent to a laterite nickel producer with available waste manganese units, the opportunity arose for HiTec to combine its existing technologies with processes (that will be discussed in this paper) to turn two waste by-products into products that are used for high-tech purposes.HiTec Energy Ltd and the Parker Centre have had a collaborative research relationship for a number of years in areas involving EMD and battery related technologies. Meanwhile the solvent extraction (SX) group of the Parker Centre (CSIRO Minerals) has developed SX processes to separate manganese from nickel and cobalt. A project was initiated by HiTec Energy to recover manganese from waste laterite leach solutions using SX technology. Batch tests were conducted to select a suitable organic system for the extraction of manganese in terms of selectivity and extraction and stripping kinetics.A total of eight organic systems were tested by determining pH isotherms of metals using a laterite nickel process waste stream. Two organic systems, the Versatic 10 and Versatic 10/synergist systems, were chosen for further test work with Shellsol D70 chosen as the diluent for both systems.The Versatic 10/synergist system would be advantageous over the pure Versatic 10 system because fewer SX stages are required, resulting in a smaller organic inventory and lower capital costs. The risk of gypsum formation is also significantly lower with the synergistic system.

Jan 1, 2004

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993