Search Documents

By Kwitko G

Exploration for coal has been on-going in South Australia for the past 100 years. During this period substantial resources of low rank coal have been delineated throughout the State. These deposits are of variable quality often with high moisture, sodium, chlorine, sulphur and ash content and although generally regarded as suitable for use in conventional pulverised fuel boilers, many are difficult to utilise. The only operating coal mine in South Australia is at Leigh Creek where coal bearing shale was discovered by chance in 1888 during excavation of a railway dam near the township of Copley. Leigh Creek has had a very diverse mining history from the initial small scale underground mining through to open-cut mining utilising draglines and more recently large shovels and trucks.

Jan 1, 1992

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

Politicians and economists talk glibly about the so-called knowledge revolution. The reality is that knowledge is fundamental to economic progress. Consequently there have been many technological revolutions. The global impacts of the invention of the steam engine and the development of the frozen meat industry are well known. Another less publicised technological advance occurred in Central Otago late in the nineteenth century. This was the adaptation of the bucketladder dredge to the mining of placer deposits. A product of over 30 years experimentation and innovation, New Zealand dredging technology was taken to the Risdon Iron and Locomotive Works, San Francisco by R H Postlethwaite, a Dunedin based mining engineer. New Zealand-style dredges built by Risdon operated successfully in California, Alaska and the Yukon. Californian engineers assimilated the best features of the New Zealand dredges with American (Bucyrus) designs to produce a standard for the worldwide placer mining industry.

Jan 1, 2003

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By Weller KR

A study of high pressure rolls grinding of a number of Australian ores and minerals has been carried out using a pilot-scale machine with rolls 300 mm diameter and 70 mm wide. The results from this study have been used in conjunction with plant survey data to construct computer simulation models of various comminution circuits and these have been used to investigate options for incorporating high pressure grinding rolls into these comminution circuits. Possible rolls options for three of these circuits are presented, and likely energy savings over the existing circuits are discussed together with potential improvements in plant throughput and/or product sizing. A scale-up procedure for predicting full-scale machine performance from small-scale testing is described, and the effects of rolls operating conditions are also discussed.

Jan 1, 1991

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

Olympic Dam Operation is located in the Stuart Shelf Geological Province approximately 520 km north-north-west of Adelaide in South Australia. It is estimated to be one of the worldÆs top five copper orebodies by size and the biggest single occurrence of uranium. The deposit was discovered by Western Mining Corporation in 1975. Exploration was based on a conceptual model for the formation of sediment hosted copper deposits together with gravity and magnetic anomalies.The capital cost of the current expansion is estimated to be A$ 1.64 billion. The underground expansion includes a total of 36 km of lateral development, a railway haulage system delivering ore from a series of ore passes to a new crusher station and a significant increase in ventilation capacity and mine services.In the current underground expansion the mining method will essentially remain unchanged. The ore handling system will incorporate some recent advances in technology, improving efficiency and safety standards.Major infrastructure excavations are designed by a team of engineers attached to the Olympic Dam Expansion Project and a number of consulting groups. Once the expansion is fully completed it is expected to increase the current annual underground production level from 3.4 Mt to 9.0 Mt of ore by the year 2000. Mine design engineers working for the Olympic Dam Operation have recently completed a three year final design plan to achieve this target.Access to the existing mine is through the decline and Whenan shaft. The Whenan shaft was originally sunk as an exploration access and later upgraded for hoisting. The 4 km long service decline connecting to the Whenan shaft was later constructed to accommodate the increase in service demand. The Robinson and Sir Lindsay Clark shafts were developed at later stages to cater for the hoisting during and following the expansion lead up.

Jan 1, 1999

By Lukaszewski GM

The indiscriminate surface disposal of coal waste in the past has created a serious fire hazard in the bush of the northern New South Wales coalfields. Spontaneous or bushfire-induced combustion in large neglected dumps of this material has increased in recent years causing a rise in air pollution. Surface methods of coal waste disposal are still being practised, and in many cases new material is being added to old dumps, many of which are burning. CSI RO has conducted research on methods of preventing and controlling fires in coal waste and recommends practical methods of overcoming these problems. Some laboratory and on-site investigations are described and the hazards of improperly constructed dumps are considered. The available techniques of fire prevention and control are discussed in relation to Australian conditions. Proposals for the safe and economical disposal of coal waste are outlined.

Jan 1, 1970

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

By J Ortiz

In almost all copper mining companies, mine planning is done considering different time frames, leading to long-term (life-of-mine) (LOM), medium-term (first three years) and short-term (first year, monthly, weekly, and up to daily plans). Shorter term plans are usually associated with more abundant information, hence models with lower uncertainty. However, they capture more of the variability found on the geological attributes. In long-term models, usually estimation methods tend to hide this variability, providing smoothed interpretations.Medium and long-term plans consider average values for the parameters and optimisation techniques are applied aimed at maximising the economic profit. Short-term plans, on the other hand, are made to comply with the medium-term promises, maximising the use of the available resources (equipment and processing capacities) and dealing with the variability not characterised in the previous planning stages. This generates an important gap between the short-term and the medium and long-term plans. A case study was made using an important oxide copper mine, where the variability found in the short-term plan has a large impact in the productive process, thus reducing the daily ore grade variability is an important goal. In this paper, this planning issue is addressed by creating medium-term mine plans using mixed integer programming which are compared using the output of a simulation of the daily extraction that is aimed at satisfying the daily constraints of the processing plant, the availability of mining equipment and the variability of ore grade. The result shows the expected gap between these mine planning processes, which suggests correcting some of the parameters used in future medium and long-term plans.

Sep 26, 2011

A field trial of the prompt neutron-gamma SIROLOG technique was undertaken by the CSIRO - Division of Geomechanics at Callide Coalfields during July 1989. The trial investigated whether the sonde could reliably be used for the determination of Ash and Iron Oxide (Fe2O3) in coal seams, which had a highly variable iron content. Ten boreholes were logged, being water filled of a nominal diameter of 120 mm. The logging probe employed a 1.6 ¦g 252Cf neutron source and a 51 x 51 mm BGO detector. The source to detector distance was 15 cm. The results from one exploration borehole at the Dunn Creek Mine are discussed in the paper. The rms deviations for ash and iron determination between the neutron-capture predictions of the geophysical logs and the laboratory - chemical assays were 1.9 per cent Ash and 0.88 per cent Fe respectively. Using existing empirical equations which relate iron oxide concentration in coal ash to Initial Deformation Temperature (reducing conditions) at Callide, it may be possible to indirectly determine ash fusion properties as least as accurately, on a more detailed ply-by-ply basis, and more cost competitively than current laboratory techniques allow.

Jan 1, 1991

By DV Boger

Rheology is the science which deals with the deformation and flow of matter. Thus nccology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the had stuff. In the upgrading processes associated with mining, is mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian hold Rheology deals with the flow of non-Newtonian fluids; therefore i combination of rheological understanding of high density suspensions. ill conjunction with an understanding of the environmental problems hero' faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By DiStefano AB, Dale SG

This paper describes the laboratory study implemented to investigate the application of the subaerial technique to tailings disposal for the proposed Olympic Dam Mine. The results of the study and the resulting design parameters are presented. The subaerial technique of tailings disposal is described and the advantages of the method for disposal in arid climates highlighted.

Jan 1, 1984

The Ramu chromite deposit occurs in the Marum Ophiolite complex and is the most economically attractive chrom-ite deposit in Papua New Guinea. Its lateritic nickel, chromite and cobalt potential has attracted several compan-ies to prospect the deposit.In the present work, the compositions of chromite in the Ramu lateritic deposit and coexisting olivine-chromite pairs in Marum Ophiolite dunite were analysed with the electron microprobe for Fe, Mg, Cr and Al. The results were used to determine the relationship between the cations in the tetrahedral and octahedral structures of the chromite. In addition, the Fe, Mg, Cr and Al cations of the coexisting olivine-chromite pairs were used to calculate the equilibrated temperatures of crystallisation of the chromite. The variation of Fe", Mg and Cr cation values of the chromite in relation to the calculated temperatures was studied by regression analysis.

Jan 1, 1994

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969

By Barro L

There is currently a world wide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow charac- teristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A Capillary rheometer, designed to handle settling suspension, has been used for deter- mining rheological properties. Brown coal of 0 0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦- 319¦C, Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physico- chemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage.

Jan 1, 1980