Search Documents

By William Fink

APPROXIMATELY two years ago the authors obtained data that indi-cated that initial precipitation could not be detected by change of lattice parameter in the aluminum-rich aluminum-magnesium alloys. Some of these data were first published in a brief note in MINING AND METAL-LURGY1. Cast specimens were used at that time and they showed initial precipitation relatively sooner than sheet material of the sane composi-tion. For this reason a more thorough investigation has been carried out using a homogenized aluminum-magnesium sheet containing approxi-mately 10 per cent magnesium. Materials.-The aluminum used in the preparation of the aluminum-magnesium alloy was of high purity, containing less than 0.01 per cent each of iron, silicon and copper. The magnesium was high-purity sub-limed magnesium. Preparation of Alloy.-Approximately 4 kg. of the aluminum was melted in a plumbago crucible in an electric furnace and the magnesium was added. The melt was thoroughly stirred with a graphite rod and fluxed with chlorine gas before casting. The alloy was cast in the form of a sheet ingot in a cold iron tilting mold (approximately 200 by 165 by 40 min.) and into small chill-cast, slabs for chemical analysis (75 by 40 by 5 mm.). The chemical analyses were made upon drillings from the analysis slabs. The analytical methods were those described in "Chemical Analysis of Aluminum," published by the Aluminum Company of Amer-ica. The composition of the alloy was found to be: magnesium 10.30, silicon 0.013, iron 0.008 and copper 0.005 per cent.

Jan 1, 1936

By G. G. Waddell, T. J. Crocker, S. S. M. Chan

A successful engineering structural design often depends upon a thorough understanding of the material properties of the structure. It is no exception when designing a supporting system for stable underground openings. For this reason, studies were made in the deep mines of the Coeur d'Alene mining district to obtain engineering properties of rocks and rock masses immediately surrounding underground openings. In this paper, data concerning laboratory tested physical properties of rocks and in-situ deformation behavior of rock masses from the Galena, Lucky Friday, and Silver Summit mines of the district are presented. Interpretations of the data so obtained and suggestions for the use of the results of the investigations as design criteria are also outlined.

Jan 1, 1973

By Frederick O?Neil

SCOPE OF THIS REPORT THE object of this paper is to describe the present status and possibilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the; iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. X. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Witherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 2, 1926

By E. H. Sellards

ON Oct. 9, 1929, a sink formed in the Sour Lake salt dome oil field in Texas, and on Oct. 12 a second smaller sink formed at the north margin of the first. The purpose of this paper is to give such observations as it has been possible to make on the earth movement incident to this subsidence. Sour Lake salt dome is typical of the salt domes of the Gulf Coastal Plain of Texas. Structurally the dome is a plug of salt which rises to within 900 ft. or less of the surface. Above the salt is a cap rock consisting of anhydrite with more or less calcium carbonate. The salt plug, as contoured on the cap rock, is circular in outline with, however, some appreciable irregularities. Overlying the cap rock are relatively uncompacted sediments consisting of sand, clay and gumbo.. At the crest of the dome these deposits are no more than 700 or 800 ft. thick. However, the sides of the dome are steep, and the sediments thicken rapidly away from the crest. The sink formed about 1500 ft. northeast of the crest of the dome where the sediments overlying the cap rock are from 1000 to 1200 ft. thick. The cavity permitting the subsidence was quite certainly either in the cap rock or in the salt below the cap rock, so that the sink was formed by the caving of as much as 1000 or 1200 ft. of earth.

Jan 1, 1930

"The greatest mining center in the state of Utah is the incorporated town of Bingham about twenty-five miles southwest of Salt Lake City. The principal industry of this vicinity, prior to the early fall of 1 863, was lumbering and the first saw-mill in the state was built near the mouth of Bingham Canyon. Early in the fall of that year, George B. Ogilvie discovered gold and shortly afterward the first mining district in the state was organized. Some writers place the discovery of gold in the canyon in the late fifties. If this be so, however, the matter was kept extremely quiet because no mining was engaged in until after Ogilvie's discovery.Bingham was a placer mining camp, producing about one million dollars' worth of dust and nuggets from placers up and down the canyon and in Bear Gulch until early in the seventies, or about ten years after the discovery of gold, when a large body of argentiferous lead ore was discovered and soon after heavy shipments were made from a half dozen or more properties.In 1 8 74, A. H. and George L. Bemis erected the first concentrating plant in the state for the treatment of sulphide lead ores.The history of the camp as a producer of copper begins in the summer of 1 88 7, when Enos A. Wall noticed, in observing prospecting drifts and inclines driven some years before, the discoloration caused by the coppery solution. As a large part of the adjacent ground had been abandoned, he located two claims, which he called the ""Dick Mackintosh"" and the ""Charles Reid,"" after two of his friends.Late in 1896, the Highland Boy Mine produced sulphide ore rich in copper, causing a revival of interest in the copper potentialities of the camp, and during the next seven years a number of new claims were located ."

Jan 1, 1925

By F. A. Forward, V. N. Mackiw

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting copper, nickel, cobalt, and sulphur from high grade nickel concentrate produced from Lynn Lake ores, and describes in some detail the chemistry of the process. IT is well known'.' 2 that copper, nickel, cobalt, zinc, ferrous iron, and a number of other metals combine with ammonia in aqueous solution to form complex ions of the form [Me(NH,)x]"+. The stability and solubility of these ions depend on the concentration of the metal ion in solution, on the amount of NH, present, and on the amount and type of anions present, e.g., OH-, C0;-, NO,, C1-, SO;-. If ammonia is partially or completely removed from such solutions, for example by boiling, the soluble ammines tend to decompose and the metals precipitate as basic salts. These properties of metal ammines have found practical application in the commercial recovery of copper, nickel, and cobalt from a variety of ores. In an operation formerly conducted at Kennecott"" the mill tailing containing 0.80 pct Cu as copper carbonate was leached by percolation with an ammonia-ammonium carbonate solution to dissolve the copper as the ammine. At Calumet and Hecla0-" With a mill tailing containing about 0.4 pct Cu as metallic copper, it has been found necessary to aerate the ammonia-ammonium carbonate leach solutions between stages to oxidize the solubilized copper. At Nicarol"-" where nickel and cobalt occur as oxides and silicates which are not soluble in ammonia, the ore is heated to decompose silicates and to selectively reduce the nickel and cobalt to metal, leaving the iron as Fe,O,, and is then leached with ammonia-ammonium carbonate solution accompanied by aeration to dissolve nickel and cobalt as ammines. In each of these leaching operations, the anion present is CO, and the metals can be precipitated from the leach solution as oxide (copper) or hydroxide and carbonate (nickel and cobalt) by boil- ing off NH, and C02 both of which are recycled to treat a subsequent ore charge. The products-—oxide, hydroxide, or carbonate—can be treated by conventional smelting, calcining, or electrolytic methods to convert them to refined metals. Thus the procedures mentioned utilize the properties of the ammines to extract copper, nickel, and cobalt from nonsulphide ores and separate them from the leach solutions. These processes have the advantage that they can be carried out in closed vessels at atmospheric pressure, that the leaching solutions are specific for the desired metals, that the metals can be recovered as relatively pure compounds by the boiling operation, and that the NH, and CO, can be recycled. Also, as the leach solutions after boiling and filtration are substantially free of metals, NH,, and CO,, they can be discarded, thus facilitating the control of the water balance in the leaching circuit. When, as is the case with Sherritt Gordon concentrates, sulphides are treated with ammonia solution in the presence of oxygen, the leach solution contains SO,--, and an entirely different set of conditions is encountered. The ammine sulphates (of nickel, for example) are more soluble than the carbonates and can be only partially decomposed by boiling. The SO, and NH, in the solutions can not be recovered by boiling. Thus, despite the more favorable leaching conditions resulting from high solubility of the ammine sulphates, the recovery of metals, NH,, and SO, from the solutions must be effected by other means. Sherritt Gordon Nickel Concentrate Treatment The Ni-Cu-Co flotation concentrate produced at Lynn Lake'" contains 12 to 16 pct Ni, 1 to 2 pct Cu, 0.2 to 0.5 pct Co, 33 to 40 pct Fe, 28 to 34 pct S, 8 to 20 pct insoluble, and less than 0.02 oz per ton precious metals. The nickel is present chiefly as pentlandite, the copper as chalcopyrite, and the iron as pyrrhotite and pyrite. Most of the cobalt is thought to be present in pentlandite, although it is known that a small amount occurs as Co-Ni-pyrite.

Jan 1, 1956

By John G. Baragwanath

THE September issue of the Engineering and Mining Journal carried an item regarding the Cercapuquio Mining Co. which was mentioned as a large producer of lead, zinc, and cadmium, situated near Huancayo, Peru. The paragraph caught my eye because I had not heard of the property in thirty years and I recollect all too well the circumstances of its accouchement. In 1916 1 was making my headquarters in the town of Huancayo, then the terminus of the Central Railway of Peru, and was examining mines and prospects in that general area for Cerro de Pasco. In the course of my work I became acquainted with an engaging and energetic "practical" miner named Balarin, a Dalmatian living in Huan¬cayo, and made numerous trips in his excellent company. One day Balarin came to the down-at-heels hostelry where I stopped and told me that a Cholo prospector, a character by the name of Jose, had just reached town and claimed to have made a discovery in a little known locality called Cercapuquio. Lead-silver, Balarin said, and showed me a sample of galena about the size of his fist. "Fine," I remarked. "When do we leave?"

Jan 1, 1947

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By G. C. Wallick, J. S. Aronofsky

This paper presents an experimental verification of numerical solutions of the differential equation describing the transient flow of an ideal gas through a porous material including gas slip effects. Several experiments previously proposed by one of the authors are described together with the correlation of the experimental results with the numerical solutions. Excellent agreement is shown between experiment and theory, thus demonstrating the validity of both the basic assumption made in the derivation of the differential equation and of the numerical solutions of the differential equation. INTRODUCTION In a recent paper,' one of the authors has discussed a numerical solution of the differential equation describing the unsteady flow of an ideal gas through a porous material. This paper was primarily concerned with the effect of gas slip on the flow behavior. In steady state measurements, Klinkenberg2 and others have observed that the apparent gas permeability Kn of a porous material may be expressed as a linear function of the reciprocal average pressure 1/P of the form, ka = b + m/P........(1) where the intercept b is a constant for a given porous material and the slope m is a constant for a given porous material-gas combination. Aronofsky1 assumed that Equation (1) could be used to describe transient flow if P was replaced by the average pressure in an infinitesimal volume element. A number of numerical solutions of the resultant differential equation were presented and specific flow experiments were proposed as a means of testing the numerical solutions. The purpose of the present paper is to describe the results of several of these experiments and the correlation of the experimental data with the results of the numerical analysis. Reference should be made to the previous paper' for details of the mathematical and numerical analysis. EXPERIMENTAL PROCEDURE A simplified schematic drawing of the experimental apparatus is shown in Fig. 1. An 8.89 cm diameter limestone core of length L = 14.82 cm was mounted in a conventional rubber sleeve permeameter cell. The external sleeve pressure in this cell was maintained equal to 500 psig during all experimental tests, thus permitting only longitudinal flow through the core. One end of the core, X = L, was connected to an adjustable cavity of volume V as well as a pressure gauge or manometer. The other end of the core, X = 0, was connected to a Nullmatic pressure regulator which was in turn connected to a nitrogen cylinder or vacuum pump. In each experiment, the core and adjacent dead volume were charged with nitrogen to a uniform gas pressure P1. The pressure at X = 0 was then suddenly raised or lowered to a constant pressure P, and the resulting pressure buildup or pressure decline at X — L was recorded as a function of the time. The porosity + and the permeability constants m and b were determined using the transient method which was suggested by the results of the numerical analysis and which was described in the earlier paper.' The following average values for these constants were obtained as a result of 19 separate evaluations: 171 -0.259 2 0.005 md-atm; b = 0.374 5 0.008 md; and F = 0.098 ± 0.005*. It should be noted that in order that transient phenomena will be slow enough to be observed conveniently, it is desirable to use a porous material of very low permeability, e.g., less than I md. Moreover, it is in this low permeability range that the gas slip effects are most significant. Thus, such a low permeability sample is very suitable for use in an experimental verification of the numerical solutions previously described.

Jan 1, 1955

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By E. B. Mayo

David LeCount Evans (Consulting Petroleum and Mining Geologist, Wichita, Kans.)-—Not only E. B. Mayo but also W. C. Lacy, who apparently urged the preparation of this analysis, is to be commended. Regional thinking of this type is needed to assure future success in the never-ending search for new mineralized and petroliferous districts. As is usually the case, here is a regional study that will be read by the mining geologist alone. It is ironic that several of the trends established in this study have suggested themselves in northern mid-continent, detailed, and regional studies. These, where established, have offered new keys to petroleum exploration and have provided a possible basis for unraveling a number of broad generalities. The oil geologists, active in Colorado, Kansas, and Oklahoma, would find much food for thought in Mr. Mayo's projections. To be more specific: 1) The parallelism between E. B. Mayo's Texas Lineament and the Amarillo Uplift, the Wichita Complex and the Arbuckle Complex of the Texas Panhandle and Southern Oklahoma is viewed with interest and appears especially significant when compared with the similar northwest trend of the Central Kansas Uplift, a major trend of production. 2) Considering the various northeast zones of Fig. 2, and with particular reference to Mayo's C-C, the Jemez Zone is on direct line with one of several northeast-southwest controls which the present writer has been using with some success in Kansas subsurface correlations. Considering zones of shearing, with no apparent vertical displacement, but suggesting strike-slip movement, because of the staggered effect on other features which cross such trends, Mayo's philosophy presents regional possibilities for lines of weakness, considered to this time of only local significance. 3) And, finally, in an area as distant from the Southwest as central Kansas, the north-south trends of the Fiarport-Ruggles anticline, the Voshel-Hol-low Nikkel-Burrton structures, the Dayton to Stut-gart trend, the north, slightly east trend of the Ne-maha structural complex, and others all seem to approach the north-south alignments, a through f, of Mayo's Fig. 3. Mayo's employment of structural intersections to pinpoint crustal weakness, to localize igneous activity and its accompanying mineralization is not, perhaps, a new concept, but it is a 1958 model, produced by tools improved from the ever-increasing accumulation of geological observations. The use of intersecting trends in petroleum geology is not a new idea, since much production in earlier days was encountered via the straight line projections of established trends to centers of intersection. A tragedy in this age of specialization is that iron curtains have been raised between groups, all seeking raw materials, all acolytes at the altar of structural geology, but all smugly content in and protected by the ivory towers of petroleum geology, engineering geology, mining geology, and geophysics. Mayo presents basic ideas which can stimulate mid-continent structural thinking and, in the case of cen- tral Kansas. he provides a key to replace the broad and overworked simple monoclinal, sinkhole-dotted, Karst topography credo, which is not finding its share of new oil in a state where the declining discovery ratio is disconcerting. The American Association of Petroleum Geologists would do well to add E. B. Mayo to its list of Distinguished Lecturers. Evans B. Mayo (author's reply)—In reply to David LeCount Evans' comments, it is pleasing to learn that some of the elements discussed in my paper may interest petroleum geologists as well as mining geologists. This should not be surprising, however, because the lineaments make up the framework of the continent, and the oil-bearing sediments must reflect to varying degrees adjustments of basement blocks along their boundaries. A further possibility that petroleum geologists must have considered is that the slow escape of heat from buried lineaments and their intersections has aided the separation of oil from the sediments and started the migration into traps. Regarding the specific points listed by Evans, the following are suggested: 1) The branch of Texas Lineament marked 1' (Fig. 3) is thought to extend eastward through the Capitan Mts., New Mexico, through the long Tertiary dikes east of Roswell, and beyond via the Matador and Electra ranges of the Red River Uplift, Texas. Its further continuation might be the eastern flank of the Ouachita Fold Belt. The Amarillo-Wichita-Arbuckle zone of uplifts appears to continue east-southeastward the Spanish Peaks belt (3-5, Fig. 3). The northwest-trending Central Kansas Uplift would not belong to the above set, except insofar as the Central Kansas Uplift is traversed by west-northwest folds, possible continuations of the Uinta belt (5-5, Fig. 3). 2) The possible continuations into Kansas of the Jemez zone are new to me and are most welcome suggestions. 3) Most of the nearly north-south Kansan structures mentioned by Evans are unfamiliar to me, but the Nemaha Uplift itself appears to be part of a very pronounced structure traceable from the Cerralvo Fault Zone, south of the Rio Grande, through the Bend Arch, Texas, and the Nemaha Uplift, into the Pre-Cambrian of Minnesota (?). This nearly meridional zone is crossed and broken by the Rio Grande Embayment and by the Red River-Wichita Syntaxis. Petroleum geologists realize the economic importance of these features. Perhaps it is inevitable that some papers of general interest be buried in the journals of specialized groups. Moreover, papers dealing with regional, or lineament, tectonics and its applications to exploration for economic mineral deposits are as yet few in the American literature. The opportunity to advance this field is open to all those who are not ultra-conservative and who have a lively curiosity, plenty of patience, and not too many business restrictions. In conclusion, much appreciation is extended to D. L. Evans for his comments.

Jan 1, 1960

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0' plates has been found to accelerate markedly the transformation of 8' to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8' —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.'-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8' to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8' boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8' plates present. Each 0 crystal simultaneously consumes the host 8' plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8' plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8' and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8' were increased moreg than the kinetics of 8' — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0' —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0' plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969

One of the best known of the early mining districts of Nevada was that at Eureka, where gold was first produced in 1864. While the most productive period for the district was during the early 1900s, production was maintained until World War II. During this time it is said that the Eureka district produced as much as $200 million from over 3,200 km (2,000 miles) of tunnels and workings. The Windfall Mine was discovered in 1902; and a 100 ton cyanide plant was operated there during the periods 1907 to 1912 and 1932 to 1940. Since 1974, however, Windfall Venture has been operating a unique heap leaching facility on the site of the old Windfall Mine. Gold at the Windfall occurs primarily in the Cambrian Hamburg dolomite which has been "sanded" and in which the original cementing material has been destroyed. The gold is micron sized and is accompanied by anomalous amounts of arsenic and mercury; however, the ore is low in base metals which distinguishes it from the typical Eureka district ores. Mining the ore causes it to break down into very fine sizes, approximately 50% minus 150 microns (100 mesh). Conventional heap leaching by spraying proved to be impossible; and extensive test work on alternate methods, aided by the United States Bureau of Mines, was conducted using 9 m (30 ft) high columns and then large tonnage heaps. The leaching procedure adopted was to build 10.6 m (35 ft) high heaps on a 50 mm (2 in.) asphalt pad covered with a layer of gravel for drainage assisted by perforated pipe drains and gravel-packed sumps. A berm is constructed around the top of each pad and cyanide solution is allowed to “pond” on top of the heap. The resulting percolation is at the rate of 24 liters per sq m per hr (0.6 gal per sq ft per hr), a figure about 2.4 times the average used in other heap leaching operations. The dolomite furnishes its own protective alkalinity and no lime or caustic is used in the solution which contains 0.4 kg per mt (0.8 lb per st) of NaCN. Pregnant solution from the heaps averages about 0.7 g Au per mt (0.02 oz per st) with a cyanide content of about 0. 2 kg per mt (0.4 lb per st) and a pH of plus 9. Addition of NaCN brings the pH of the leach solution up to 11 to 12. Carbon adsorption of the gold was originally done in six enclosed columns mounted in a trailer but five conventional columns have been substituted as the size of the operations has increased. Carbon stripping is with hot caustic, cyanide and 10% ethanol solution. The

Jan 1, 1981

By T. R. Ingraham

The thermal decomposition of Nickel (II) sulfate was examined by determining the total pressure of SO3, SO2, and O2 developed over a sample when it was heated in an evacuated system fitted with a Pyrex-bellows mercury manometer. The equilibrium pressures were combined with previously published data on the oxide and sulfide systems to establish a predominance volume diagranz for the Ni-S-O system over the normal range of roasting temperature and gas composition used in the treatment of nickel minerals. The protective coating of NiSO4 which forms on the oxide during roasting, and which causes the sulfation reaction to almost cease, may be disengaged readily by temperature cycling. When nickel sulfide is roasted in air, either nickel sulfate or nickel oxide may be formed by altering the experimental conditions. Because of the differing stabilities of various metal sulfates and oxides, possibilities exist for separating some of the constituents of mineral mixtures by the technique of selective sulfation and oxidation roasting. The experimental information required to make reasonable predictions of the possibilities of this technique is incomplete and, in some cases, in conflict. As part of a general program of providing some of the required information, a study EXPERIMENTAL Materials, Apparatus, and Procedure. Fisher certified reagent-grade nickel sulfate hexahydrate was used in the source material for both nickel sulfate and nickel oxide. The manufacturer's analysis indicated: 0.001 pct Fe, 0.005 pct Cu, 0.003 pct Co, 0.001 pct C1, other 0.15 pct. The material was dehydrated, before use, by heating at 420°C for 5 hr. The oxide was prepared by roasting the sulfate in an open tray in a muffle furnace for 10 hr at950°C. Preliminary experiments which were made by thermogravimetric analysis and X-ray diffraction analysis established that only one crystal form of nickel oxide and one of nickel sulfate were involved in the equilibrium shown in Eq. [I]. The apparatus used in the experiments was described previously.1,3 The main feature is a corrosion-resistant, flexible Pyrex bellows which is used to protect the mercury in a u-tube manometer. Before a run was begun, the apparatus was washed thoroughly with hot hydrochloric acid and water and dried by heating under vacuum. The mixed sulfate -oxide sample was contained in a platinum bat rest-

Jan 1, 1967

By A. U. Seybolt

Since the time this topic was originally treated in 1954, more recent French3,1 work has been published making it advisable to repeat the earlier oxygen solubility experiments, but using iron of a higher purity. Upon repeating oxygen saturation experiments with zone-refined iron, it was found that the oxygen solid solubility was at least an order of magnitude less than previously observed. SINCE the publication of an earlier paper1 (1954) on this subject by the present author, several contributions on this topic have appeared. Meijering2 in 1955 attempted to reconcile recent conflicting solubility data, without reaching any definite conclusion. sifferlen3 (1955) found that iron of high purity appeared to absorb a quantity of oxygen (0.005 to 0.025 pct) approximately proportional to the structural imperfections present, such as polygonization and grain boundary area. However, he also indicated that purity itself was a significant factor. He concluded that very pure iron nearly free of lattice imperfections would have essentially zero oxygen solubility. His second paper4 (1957) supported this contention since a zone-melted iron containing initially 0.0007 pct O analyzed only 0.0006 pct 0 after prolonged soaking at 850°C with an FeO layer on the surface. Because of the discrepancy between the results of Ref. 1 and those of Sifferlen, it seemed desirable to attempt to resolve this disagreement. EXPERIMENTAL PROCEDURE AND MATERIALS The experimental method used by sifferlen3,1 was essentially the same as that of Ref. 1. In this technique thin iron strip with a surface layer of FeO is soaked for prolonged periods at an elevated temperature in order to saturate the iron with oxygen. After two days at temperatures near 800° to 900° C, one would expect that the iron would be in equilibrium with the surface FeO. In the work reported in Ref. 1 there was evidence that two days holding at 8000to 900°C was more than sufficiently long for saturation. Sifferlen used 48 hr at 850°C. Because of the evidence presented by Sifferlen that the apparent oxygen solubility is a function of iron purity, three grades of iron were used as indicated in Table 1. The Bureau of Standards wire was used only for resistivity tests, while the other two irons were used for saturation-analysis tests of the type described above.

Jan 1, 1960

By A. F. Meston

Centrifugal force has been used for centuries for separating liquids but machines for doing this are a comparatively recent development. The use of these machines is being extended into many industries but this paper is confined to their use in the oil industry. The centrifugal machine is found at the well where "cut oil" is dehydrated for acceptance by pipe lines; and in the refinery and byproduct plant. In fact, wherever finely divided suspended particles should be removed from an oil, there is a possible use for a centrifugal machine, if the particles have, or can be made to have, a specific gravity different from that of the oil. Centrifugal machines are also used for cleaning fuel and lubricating oils and dehydrating transformer oils. Applications and Results When oil comes from the well mixed with water, it is spoken of as cut oil. Settling often does not remove sufficient water for the oil to be accepted by pipe lines, thus necessitating chemical or other treatment. Centrifuging alone, or following chemical treatment, effectively prepares such oil for pipe lines, as is shown by the following data: WateR, Etc. Wat~R. Etc. Temperature, Oil to Pipe Line, aT StUt at Finish Degrees F. Bel. Per HouR PIE Cent. PEECent Oklahoma lease.... 160 10 10 0.25 Kansas lease....... 125 4 20 0.25 to 2 On the Oklahoma lease, the machine was cleaned of solid material once in 12 hr. At first, it was thought that chemical treatment was necessary to start separation and 1 qt. of prepared compound was added to each 100 bbl. of the cut oil before centrifuging. Later it was found that

Jan 1, 1924

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By W. W. Little

At the United Verde mine the 9-2D stope on the 4050 ft level is located within the north sulphide mass lying some 800 ft north of the main sulphide ore body. In 1948 it was estimated that this block contained 85,000 tons of ore at 4% copper and 9.2% zinc. The north ore body is a lenticular replacement deposit in the black schist, extending from about 100 ft above the 3750 level to a distance below the 4500 level yet to be determined. Although the mineralized zone approaches 1000 ft in length, only 300 ft is of economic importance. In width it varies from a maximum of 60 ft to about 3 ft at the north end, and is characterized by pinching and swelling in the ore zone. One of these larger swells is being mined as the 9-2D stope. Mining costs at greater depth, together with the expected grade of ore after dilution, necessitated a low cost mining method to permit profitable stoping operations. Based on the results obtained in a number of Canadian mines, it was decided to develop the ore body for stoping by the Aldermac or bench method of diamond drill blastholes; however, this plan was subsequently changed and the radial or ring method adopted. Such a method seemed to offer the advantage of large tonnages at low cost, and obviate the necessity of waste fill. This latter point was of particular importance, since the present waste system does not extend below the 3000 level.

Jan 4, 1950

By J. J. Rutledge

I. DESCRIPTION OF THE CLINTON ORES AND ASSOCIATED POCKS. THE Clinton rocks in Stone Valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.1 A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the tipper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, Composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Nov 1, 1908