Search Documents

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite,* and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe2O3) and maghemite (gamma-Fe2O3) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, however, occurs largely as goethite (Fe2O3-H4O) and hematite (Fe2O3) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated. MAGNETIC ROASTING Hematite undergoes a stepwise reduction when exposed at moderately elevated temperatures to a reducing atmosphere containing hydrogen or carbon monoxide: Fe2O3? Fe3O4 ? FeO ? Fe Since the desirable product in magnetic roasting is Fe3O4, the conversion is halted after the first stage by controlling the reduction potential of the gas mixture with water vapor or carbon dioxide. The reducing gas mixture must be such that the oxygen partial pressure at the solid-gas reaction interface will be maintained intermediately between the oxygen partial pressures in equilibrium with Fe2O3 and Fe3O4 at the prevailing temperature. Because of the rapid increase in decomposition pressure of Fe3O4 with increase in temperature, the practical upper limit of useful reaction temperature is about 1400°F, above which over-reduction usually occurs in atmospheres containing hydrogen or carbon monoxide. On the other hand, useful reaction rates usually occur only above 800°F. Goethite reacts similarly except that the combined water probably has to be driven off thermally before the reduction to magnetite occurs. Iron carbonate must also be decomposed thermally to an oxide before conversion to magnetite. Iron silicates are apparently not amenable to magnetic roasting. The rate of penetration of the reaction toward the interior of a given ore fragment is dependent on the chemical composition and physical structure of the solid. Most ore fragments tested here reduced satisfactorily to 1/4-in. depth in less than 14 min at 1200°F. Some very dense fragments, however, were reduced to less than 1/32-in. depth under the same conditions. Determination of the optimum temperature, gas composition, ore fragment size, or time of exposure

Jan 1, 1961

By Edward Capillon

THE problem of scrap is probably of greater importance inn the production of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of the base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is. not generally feasible to assay every shop remelt it follows that the possibilities of lost values are large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base, metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys.

Jan 1, 1930

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By C. David Mann

Metal prices continued to improve in 1964, resulting in the opening of new mines and re- activation of old ones. Larger and deeper shafts are being bored. At the AEC's Nevada Test Site, a 72-in. diam shaft is being bored to 3200 ft. In New Mexico a 1650-ft shaft was bored with a 48-in. bit, then reamed to 124 in. to 935 ft, and 102 in. to 1650 ft. Deviation was only 26 in. In California a shaft sinking machine has been developed which combines drilling and mucking equipment into one mobile, integral unit.

Jan 2, 1965

By C. G. Wilson

DURING the course of some experiments on the plastic deformation of gallium a standard stereo-graphic projection was prepared with (001) at the center and it was felt that this might be useful to others working with single crystals of gallium. The stereogram, given in Fig. 1, was made using the following crystallographic data (Bradley, 1935):

Jan 1, 1962

By Ernst M. Cohn

The demonstrations of the "Silent Sentry" by Union Carbide Corp. in 1957 and of a special tractor-plow by Allis-Chalmers in 1959 ushered in the technology era of fuel cells. The idea for direct conversion of chemical to electrical energy, first published in 1801 by Davy in England and Ritter in Germany, has been kept alive by a few people through 150 years: Grove built the first hydrogen-oxygen fuel cell in 1839; Mond and Langer made electrolyte contributions around 1890 that are still used today; Baur worked on coal-based cells from 1900; Bacon started his work in the '30's, which resulted in the first multi-kilowatt unit in the '50's; Davtyan studied molten-salt electrolytes in the '40's, followed by Ketelaar in the '50's; and Justi developed highly active electrodes in the '50's, to name only some of the pioneers. Despite the tremendous increase in research and development of fuel cells, these direct energy converters are still in their infancy. They will find their functional application in space, where power density must be maximized and product water utilized. These early systems will provide valuable experience in system engineering and reliability.

Jan 9, 1964

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,&apos;, &apos;9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By William P. Shinn

Jan 1, 1880

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased-capacity electric transmissions using either wheel-mounted or axle-mounted traction motors makes a reality of single-axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cu yd and a working weight of nearly 1,500,000 lb. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTROTORQUE control system. Electrotorque is a completely static, solid state electronic system supplying controlled power both to the armatures and to the fields of the d-c shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corp.

Jan 1, 1970

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

Organization Place Date 1919 American Society of Mechanical Engineers... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers.... Savannah, Ga. Dec. 3-6 Geological Society of America..: Boston, Mass. Dec. 29-31 American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America.. New York, N. Y. Jan. 13 American Institute of Min. and Met. Engineers New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26 American Electrochemical Society Boston, Mass. Apr. 8-10* *On Apr. 9, a joint meeting will he held with the A. I. E. E.

Jan 12, 1919

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush&apos;s work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957