Search Documents

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By G. Das, S. V. Radcliffe

The substructural features developed in tungsten as a function of annealing temperature (up to 2200°C) and type of material [undoped and doped powder metallurgy (PM) tungsten and electron beam melted tungsten] have been investigated by transmission electron microscopy. For doped PM tungsten wires, characteristic "par-ticulate" substructural features developed rapidly with increase in annealing temperature above 700°C. The features consisted of parallel rows of elongated or circular shapes (500 to 1000A diam) lying along the direction of the wire axis and were identified as internal voids by diffraction contrast experiments. In recrystallized doped PM rod, larger voids were observed and were identified by precision dark field analysis to be cubic in shape and bounded by (100) planes. In marked contrast with both the doped PM materials, recrystallized undoped PM rod exhibited only very occasional and randomly arranged voids. Furthermore, no voids were observed in either material after electron beam melting. The high concentration of voids in the doped PM materials is attributed primarily to vaporization of doping additions or their pvoducts situated at the original grain boundaries , whereas the few voids in undoped material are considered to be traces of microporosity which were not eliminated during sintering. A tentative mechanism is suggested for the dezlelopment of the voids in relation to the processing sequences (sintering and working) and to the subsequent annealing. In recent years, a characteristic substructural feature consisting of rows of small elongated or circular regions of light contrast lying along the direction of working has been seen in thin foil electron microscopy studies of annealed sheet, wire, and rod tungsten. These features were present in the published micrographs of sheet by Weissmann et al.1 and of wire by Meieran and Thomas2, although the authors did not draw attention to them. Wronski and Fourdeux3 observed similar features in sintered rod tungsten (it was not specified whether or not the material was doped*) and interpreted them on the basis of their ap- particles, based on extraction replica evidence from the fracture surface of the initial hot-rolled slab material from which the sheet was prepared. No diffraction contrast experiments on the features were reported in any of these studies. The present investigation was undertaken with the primary objectives of: a) identifying the nature of these substructural features in tungsten by electron diffraction contrast experiments, since the contrast for voids can be expected to differ from that for crystalline or glassy particles, and b) elucidating the origin of the features and their development. For the latter purpose, doped and undoped powder metallurgy tungsten was obtained as rod and wire to represent different stages of reduction during final processing. These materials were examined both in the as-processed condition and after annealing to successively higher temperatures. In addition, the same doped and undoped materials were examined after vacuum melting in rod form. I) MATERIALS AND PROCEDURE Doped powder metallurgy (PM) tungsten wire (commercial purity 99.9 pct W) was obtained in the as-drawn and surface ground condition (0.030 in. diam "ground seal rod"). Doped and undoped tungsten rod (0.075 in. diam) representing an earlier stage of final processing was obtained from the same commercial source (Refractory Metals Division, General Electric Co.). Lengths of both the doped and undoped rod materials were single-pass melted in an electron-beam zone refiner to examine the effect of vacuum melting on the substructure. Annealing was carried out in a tungsten crucible in a tantalum strip resistance furnace under a vacuum of l0-15 mm Hg. Longitudinal sections of the wire and rod materials were examined by light and electron microscopy. The preparation of thin foils suitable for electron transmission from 0.030 in. diam tungsten wire and the rod specimens was carried out by means of a high-precision microjet technique developed to provide lack of jet stability and precise control of the area thinned. The method is described in detail elsewhere.' The foils were examined in a JEM 6A electron microscope using a goniometer stage (±20 deg tilt, 360 deg rotation) and operated at 100 kV. To minimize contamination problems a 200 µ condenser aperture was used in conjunction with a useful beam current of 50 µA. II) RESULTS AND DISCUSSION A) Diffraction Contrast Analysis. In order to determine the optimum conditions for the development of the substructural feature, a series of isochronal 30 min annealing experiments were carried out on specimens of the doped PM tungsten wire. The transmission electron microscopy analysis showed that the as-drawn wire, Fig. 1(a), consists of 'fibers' whose long axis is closely parallel to the wire axis of (110). The fiber width averages some 0.5 µ. Dense disloca-

Jan 1, 1969

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1914: Members BAKER, FRED SHERMAN Tabowie, Unsan, Korea. BISSET, DANIEL GEORGE, Engr., 142 3d Ave., N. W., Edmonton So., Alberta, Canada.. BRANDT, MAURICE SHELDON, Chief Engr., White Eagle Mining & Milling Co., Box 298, Boulder, Colo. BROWNING, EDWARD, Min. Engr., Asst. to Supt., Cornwall Ore Bank Co., Cornwall, Pa. CASTLETON, WILLIAM ARTHUR, Mill Supt., East Butte Copper Mining Co., Butte, Mont. CHIDESTER, WALTER BARCLAY, Min. Engr., Care Mother Lode Mine, Greenwood, B. C., Canada. CLARK, EDWARD HARDY Mgr.,.Hearst Estate, 15 Broad St., New York, N. Y. CLARK, FREDERICK P., Chief Chem., International Lead Refining Co., East Chicago, Ind.

Jan 9, 1914

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.' Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.' For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By C. R. Swarts

The use of compressed air or gas in oil wells for raising crude oil to the surface has, within the last year, become a dominant factor In production engineering. Previous application of this principle was largely confined to oil wells that had been pumping for a considerable length of time. In the Seminole area, the gas-air lift has been applied to wells imniediately after natural flow has ceased and in some cases while the wells were still flowing. This early application of the gas-air lift has been watchcd with intense interest by the petroleum industry, both with respect to methods of application and mechanical installations and to the effects on immediate and ultimate production. Methods of Application The Seminole pool at its inception contained sufficient gas associated with the oil to cause natural flow. As no frce gas was found in the main productive horizon, the Wilcox sand, all the gas present was dissolved in the oil, hence the natural flowing life was short, rarely lasting over 45 days. When natural flow ceased, high fluid levels were common, and as depth and crookedness of holes were obstacles to efficient pumping, the gas-air lift was used almost exclusively in raising the oil to the surface. Because of the high gravity of the oil, 41" A. P. I., and its high gasoline content, and also because of the desire to obtain production before offset wells became productive, quantity of production was the aim of the operators and a method of flow was used whereby this aim could be fulfilled. One of the outstanding features of this method consisted in flowing the wells through the annular space between the tubing and rasing. By this means a greater quantity of fluid could be handled than by flowing through the tubing of the size in ordinary use. Wells that would produce only a few hundred barrels on the pump were by this rnethod made to produce as high as 7000 bbl. on the lift. A few days or wreks of production at that rate meant a large recovery of oil. Casing of 636 in. diameter was commonly used as a production string with a 5 3/16-in. liner set on top of the oil sand. Upset tubing for irtro-

Jan 1, 1928

By B. C. Allen

The solubility of chromium in liquid silver and that of molybdenum and tungsten in liquid tin have been determined by equilibrating Ike Liquid in a crucible of the solule metal. Generally the weight of solute in solulion was delermined both chemically and from crucible weight losses. The resulting weight percent solubilily of chromium in silver as a function of absolule temperature T is given by log w = -6660/T + 4.02 in the range 960° to 1445°C, and that of molybdenlttrl in tin by log w = —5050/T + 1. 79 in the range 1200° to 2200°C. The values appear unaffected by minor changes in solute composition. Calculations aye made of the parlial molar heal and excess entropy of mixing. The estimated solubility of tungsten in tin is 0.001 pct at 2000°C. Evidence is presented that molybdenwm dissolves in tin without compound for mation and that tungsten and tin form W10Sn. RECENT developments in coatings, heat transfer, and brazing require a knowledge of equilibrium solubilities in a variety of systems at elevated temperatures. Of particular interest are solid-liquid interactions in metal systems involving dilute solutions. This investigation was undertaken since little is known about the phase relations or solubility of chromium in liquid silver or of molybdenum and tungsten in liquid tin.1,2 EXPERIMENTAL WORK As indicated in Table I, high-purity metals or those of known impurity levels were used. Crucibles were machined from chromium, molybdenum, and tungsten bar stock 1.3 cm diam and 2.2 cm long. Chromium rod was prepared by arc melting and extruding iodide process crystals.3 The five chromium impurity alloys were in the form of 0.6-cm-diam swaged rod. A Cr-0.06N* alloy was prepared by exposure to NH3 at 1150°C in a closed quartz capsule for 24 hr. Because significant nitrogen was lost during annealing in argon at 1600°C,4 the estimated level was 0.01 pct N. Chromium and Mo,W crucibles were outgassed at 1200" and 1600°C, respectively, at 3 X 10-5 mm. The solvent was placed In crucibles of the solute metal- 6 g Ag in chromium, 0.4 g Ag in the five chromium impurity alloys, and 4 g Sn in Mo,W crucibles. The silver and tin series were outgassed at 900" and 110O°C, respectively, and held at the desired solution temperature in a tantalum resistance furnace under 1.05 atm 99.995 pct Ar. An equilibration time of 0.5 to 1 hr was chosen since 0.3-, I-, and 4-hr anneals at 1235°C for Cr-Ag yielded similar results. Temperatures were measured optically to +10°C under essentially black body conditions which were checked against the melting point of silver. The Cr-Ag and Mo-Sn,W-Sn series were respectively equilibrated at 990° to 1400°C and 1200" to 2000°C. Vaporization losses were generally held to <1 pct by the argon. In the 1800" and 2000°C anneals for 0.5 hr, the crucibles were placed in tightly sealed tantalum cans which kept tin losses to <5 pct. After the anneals, the specimens were furnace-cooled. One anneal was made on small Mo-0.02 C, Mo-0.5Ti-0.lZr, and tungsten crucibles containing tin at 2200°C. The metals were sealed in an electron-beam-welded tantalum can of minimum volume. After the anneal, tin was still present in each crucible, none of which was severely attacked. After equilibration, the saturated solvent metal was selectively removed from the crucible by acid leaching. Weight losses sustained by the crucibles were determined from the initial weight minus the final blank-corrected weight after acid leaching. Chemical analyses were performed on some of the samples. Hot 1:l HNO3-H2O removed silver from chromium with the blank running <0.1 mg or <0.002 pct on measured solubility. Tin was removed from molybdenum and tungsten by hot concentrated HC1 with the respective blanks amounting to -0.004 and -0.0004 pct in the presence of tin. The insoluble residues were weighed and checked for composition. The leaching solutions contained traces of the solute metals which were analyzed by colorimetric methods, Diphenyl Carbazide for chromium, Thiocyanate for molybdenum, and Dithiol for tungsten. The total of the two percentages found from the residue and leaching solution minus the blank gave the desired solubility values. On the basis of annealing empty molybdenum and tungsten crucibles, weight losses due to MoO3 or WO3 volatilization were found to be generally 10.4 mg and affect measured solubilities by <0.01pct. RESULTS AND DISCUSSION Chromium-Silver . Since no intermediate compounds are reported to form in the Cr-An system,&apos; crucible weight losses and chemical analysis of the entire melt should provide reliable measures of the chromium in solution. Values obtained by the two methods are in agreement as shown by the results for unalloyed chromium in Table II and plotted in Fig. 1. Furthermore, the results are consistent with those previously determined by melting equilibrated silver out of the crucible and analyzing calorimetrically for chromium.&apos; On the basis of limited thermal analysis data, the solubility of chromium in silver has been quoted as 8 pct at the monotectic temperature of -1445°C.1 This investigation indicates an extrapolated solubility of 1.38 pct which is believed to be more reliable. At the eu-

Jan 1, 1968

By E. C. Bohlen, H. l. Burghoff

THE work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and Glocker;1 Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45° to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (113)[112], (001)[100], and a combination of (110)[115] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,6 who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. TEST MATERIALS AND EQUIPMENT For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, 13 ½ in. wide and 1 ½ in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk&apos; also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data&apos; for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700&apos; and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,&apos; were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data&apos; for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700&apos; and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,&apos; were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By John J. Egan, A. B. Kinzel, Walter Crafts

The demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low temperatures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selection of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low temperatures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120&apos; C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 &apos;poises&apos; times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946