Search Documents

By Frank C. Roberts

Neglecting the hydrogen and hydrocarbons, 1 will assume the following analysis as a fair average composition, by weight, of the waste gases escaping from a coke-burning blast-furnace: CO2............17.25 CO,............25.25 N,.............57.50 100.00 The 25.25 CO requires for combustion 62.6 of air, or 11.398 of oxygen, necessitating the passage of 48.202 nitrogen into the products of combustion. The latter, therefore, have the following composition: CO2,,............ 56.9 N,............105.7 Tile total specific heats of these quantities of the respective gases are 12.31 and 25.79, giving for the combined product, 38.1 approximately. That is, the product of combustion will absorb 38.1

Jan 1, 1889

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By Albert F. Hill

The manufacture of structural shapes in steel of uniform quality, which shall command the full confidence of the engineer, is a problem in practical metallurgy which is beginning to attract much attention in this country. The progress of the past fern years in the improvement of plant and processes has placed it within the power of the steel-maker to supply a material of such chemical composition as will meet the requirements; but this solves only in part the difficulties of the constractor. It is well understood that the influence of shop manipulations is a most decisive one upon the mechanical properties of the finished product; in many cases so great, in fact, as to cause an entire transformation in the character of the material, and to render it unfit for the service for which it was intended. On the other hand, mechanical treatment is frequently resorted to as an efficient corrective of certain undesirable properties, which may be due either to chemical composition or previous manipulation. This understood and accepted, it is evident that careful investigation of the effects of mechanical treatment is fully as necessary to the successful use of steel in engineering structures, as the investigation of the influence exerted by its chemical composition. All structural material has to undergo more or less mechanical treatment, such as shearing, punching, upsetting, etc. Each of these operations produces effects which are far more marked and decisive in steel than they are in iron, and means must therefore be adopted to counteract, or at least to modify, these effects before the material is permitted to enter the structure. The fact that both shearing and punching affect the tenacity and elasticity of steel has long been recognized; bat, through more recent investigations, it has been established that these effects are purely local, and are therefore susceptible of correction by other and simpler means than annealing. The importance of this discovery to the use of steel in structures is very great. The impracticability of

Jan 1, 1883

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By W. D. Felix, R. D. Smith, J. A. Campbell

The mechanism most consistent with available information on atmospheric trace element emissions involves the volatilization of a significant fraction of many trace elements during coal combustion, with subsequent condensation on fly ash as the combustion gases cool. The larger surface-td-volume ratio of the smaller particles leads to an enrichment of the volatile trace elements. From an environmental viewpoint, the submicron size particles are of greatest concern. These particles show the highest concentrations of trace elements, are least efficiently collected by pollution control devices, have high atmospheric mobilities, and are deposited preferentially in the pulmonary and bronchial regions of the respiratory system. The mechanisms for trace element enrichment and formation of submicron particles will be described.

Jan 1, 1981

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep underground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county provides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest competitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By P. G. Beckett

THE problem of handling the large quantities of water encountered in the Old Dominion mine presents many features of interest. In the present paper are discussed the probable sources of water, the pumping equipment, the increased flow into the mine in the early part of 1915, culminating in the flooding of the 18th and 16th levels in March of that year, and the difficulties that were met with during the high-water period. I. PRELIMINARY The Old Dominion mine, situated 1 mile north of the town of Globe, Ariz., has long been one of the prominent copper producers of the State, and until the opening up of the copper schist deposits in the neighboring mines of Miami, was responsible for the greater part of the copper output from the Globe district. As the gradual exhaustion of its orebodies near the surface led to the downward development of the mine, more water was encountered in the western portions directly underlying the dacite formation until the drainage problem became a serious factor in the operation of the mine and in the economical extraction of the ore. A heavy inrush of water on the 10th level of the mine in 1906, preceded by still earlier water difficulties, rendered imperative the immediate installation of a pumping equipment capable of handling large flows of water. While the Old Dominion has been recognized as a wet mine since its early clays and one in which the complete control of the water situation was of paramount importance in the development of the lower levels, it is chiefly in the last nine years, since the installation of the increased pumping equipment, that the mine has developed and handled large quantities of water.

Jan 4, 1916

Report of President The important fact of the year 1916 is that on July 25 contracts were executed by which the American Society of Civil Engineers because an additional Founder Society and arranged to make its permanent home in our building. The contracts provide for the construction of three additional stories to the building, the American Society to pay the cost tip to $250,000, this being considered equivalent to what each other Founder Society had contributed, the American Society to participate in the original Carnegie gift and have an equal share in the property with each other Founder society. The construction of the addition to the building is under way, $62,525.04 having been expended thereon in 1916. It has been found that, clue to war conditions and the advanced price of materials, the cost of the addition will be $300,000. The founder societies have been requested to assume the extra $50,000, one quarter each. This work is in charge of a Building Committee consisting of H. H. Barnes, Jr., Chairman, E. G. Spilsbury, Charles Warren Hunt and Charles F. Rand. At the request of the Founder Societies, important alterations were made in the lecture halls on the fifth floor of the building to make the same suitable for social functions of the societies. The cost, $6,642.08, was advanced by the United Engineering Society but is to be paid eventually by the Founders. The Library of the civil Engineers is being merged with the Library of the United Engineering. Society and the other founder societies. At the present time the membership of the four founder societies is 29,000 and of associate societies 23,000, so that a total of 52,000 engineers now have their headquarters in our building. The value of the real estate now owned by this Society is $1,647,171.16. This sum will be increased at the end of 1917 by the amount of the cost of the addition to the building.

Jan 3, 1917

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By M. A. Mahtab, T. M. Yegulalp

This paper presents the development and application of an approach for clustering fracture orientation data. Data are projected on the surface of the unit upper hemisphere and the clustering approach is applied in three steps: (1) randomness test and identification of dense clusters, (2) estimation of cluster statistics, using Bingham distribution, and (3) rejection of extremal data based on Chauvenet's criterion.

Jan 1, 1982

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By John Hall

THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 1 1/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. I this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. .

Jan 7, 1913

By R. F. Shurtz

The author proposes a method used with some success on a magnesite deposit at Gabbs, Nev. He believes this procedure to be more sound than the blind practice of assigning uniform quality to large, soinetimes vast blocks or ore on the basis of analyses made of a small number of samples. When an ore deposit is evaluated on the basis of core sampling, questions always arise as to how much weight should be given the various sample grades and how the deposit should be divided into specific volumes assigned to corresponding grades. For a tabular deposit it is customary to use the so-called zone-of-influence. This zone is usually defined as the polygon in the plane of the deposit having corners halfway between a given core drill intersection and each of the nearest neighboring intersections. The volume of the ore in this polygon is assigned the analysis obtained from the drill core taken at the intersection. In massive or irregular deposits, volumes of various shapes may be defined with respect to the locations of drill core samples. These volumes may be regarded as three-dimensional zones-of-influence; the theory involved in assigning the values of the central analyses to the ore in the volumes is the same as that used in the case of a tabular deposit. The zone-of-influence method was used in evaluating one of the magnesite deposits at Gabbs, Nev.'-"

Jan 1, 1960

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada. 1935. GUILLAUME DANIEL DELPRAT Melbourne, Vic., Aust. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EILERS New York, N. Y. 1922. FEDERICO GIOLITTI Trino,Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER New York, N. Y. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDOAEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T. A. RICKARD..... Victoria, B.C., Canada. 1933. ALBERT SAIVEUR CAMBRIDGE, MASS.

Jan 1, 1937

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal.

Jan 1, 1943