Search Documents

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By William Campbell

The structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, a series of transition-products with distinctive structures, to which have been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-pro-ducts—all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron carbon diagram and the structures met with in hard-

Jan 1, 1913

By F.B. Foley, S.P. Howell

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923

By S. P. Howell, F. B. Foley

Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Minea, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there exkted unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metallographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Minea and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. P. B. Foley, Metallurgist, Bureau of Mines. S. P. Howell, Explosives Engineer, Bureau of Mines. Comdr. 0. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 1, 1923

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately A 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carban content almost as high as the good anthracite, it is not

Jan 1, 1943

By AIME AIME

MONDAY evening a reception, supper and bridge in honor of the guests of the Woman's Auxiliary was given by the New York Section in the Engineering Woman's Club. After supper, tables were made up for bridge. Some tried jig-saw puzzles, while others merely visited. On Tuesday morning the annual business meeting was called to order by President Bassett. Mrs. Bassett read a note from Mrs. Hoover regretting her inability to be present, and then gave her welcome and message: It gives me much pleasure to welcome you in this annual meeting, and I hope you will be able to come next year, and those who are not able to come this year I hope will be here next year.

Jan 1, 1933

By B. G. Klugh

(New York Meeting, February, 1912). IN a paper before the Institute at Wilkes-Barre, Pa., June 1911,1 Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author2 described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some technical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taken from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, and its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sintered is intimately mixed with

May 1, 1912

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By Arthur S. Dwight

THE last decade of the 19th century was a peculiarly interesting one in. the annals of American metallurgy, especially as concerns the lead and copper- smelting industries; and it may be interesting to review briefly one of the outstanding incidents of that period, the development of the mechanical roasting furnace. I shall not pretend, in these reminiscences, to give with absolute accuracy the sequence of events or dates, nor to present a complete history of the period, but shall seek merely to 'sketch a more or less impressionistic picture with some of the underlying facts and causes as the recollection comes back to me and then point out how the present-day practice grew out of those activities. My acquaintance with the developments in Montana was based on occasional visits and general collateral information, but in Colorado I lived through the episode and was of it.

Jan 1, 1921

By Vernon F. Swanson

An equation has been developed which will permit the direct determination of free settling velocity of any sized particle encountered in mineral benefici-ation. The equation is based on Newton's Law with the friction factor defined as a function of the laminar boundary layer. Development of the equation is described first from an empirical trial-and-error approach. Examples are given of actual settling data from the literature versus calculated data to prove the validity of the new equation. Newton's law of resistance of a fluid to flow around a sphere is expressed in Eq. 1. Free settling velocities can be determined by setting Eq. 1 equal to the gravitational force on a particle and solving for V. Experience has shown that when the solids are greater than 1 mm in diam, or when Reynold's number for the system is greater than 800-1000, the friction factor term, fD, essentially becomes a constant, and Eq. 2-b becomes Newton's equation for free-settling and is applicable under the conditions stated. Another special condition exists for particles smaller than 0.05 mm or when Reynold's number for the system is less than three. In this case fD=24/NRor24µ/pL,dV,. Eq. 2-b can then be rewritten as

Jan 1, 1968

By Francis Lucas

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or-under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black, oxide that cannot be absorbed by the metal.

Jan 1, 1927

The plans for the activities of the Petroleum Division for the coming year do not differ materially from those of the past several years. The fall meeting is scheduled for Oct. 12 and 13 and is to be held at Tulsa, Oklahoma. The Division, of course, will take part in the annual meeting of the Institute at New York. A fall meeting will also be held in California at approximately the same time as the meeting at Tulsa. A number of papers are to be presented at the two meetings simultaneously. The various committees are at work arranging the programs. The Division will continue to be active in its various fields of endeavor, such as stabilization, production reviews, and economics, but special stress is to be laid on the engineering and research fields. In the past the Division has served as a forum for open and frank discussion of problems confronting the engineers in the oil industry. It is hoped that it will continue to function in this capacity. Papers presenting original ideas and extending the boundaries of knowledge and understanding in the field of petroleum production will be welcomed. Members who have interesting information to contribute should not wait until called upon by one of the Committees, but should offer a paper at the earliest opportunity. The past year has seen a decided strengthening of the control over production, with prospects of even more rigid control in the future. It is essential that production programs under such control be carefully planned and it is highly desirable that petroleum engineers take an active part in the planning, to insure efficient production of oil and minimize the waste of this natural resource. At a time like this, when it is difficult to keep the production of oil within reasonable limits, it may seem unnecessary to improve the efficiency of production methods, but, as has been aptly said, the trouble is not that we have too great a reserve of oil but that we are producing tomorrow's oil today. Therefore it behooves those who are entrusted with the engineering and scientific phases of production to learn how to get the greatest yield economically possible from the present and future fields in order that we may enjoy the advantages of petroleum products for a long time to come.

Jan 1, 1934

By C. W. Allen, B. D. Cullity, H. S. Choi

The torsional deformation of aluminum and magnesium crystals is investigated, with particular reference to the dependence of proportional limit on crystal orientation. The proportional limit is found to be governed by the average value of the resolved shear stress on the most highly stressed slip systems, but the proportional limit does not strictly obey a critical-resolved-shear-stress law. The behavior of a cylindrical single crystal stressed in tension is well known: plastic flow begins when the resolved shear stress on the most highly stressed slip system reaches a critical value. There is much less understanding of the effect of torsion on such a crystal and on the way in which the critical-resolved-shear-stress law should be applied to torsional deformation. In the present paper particular attention is paid to the dependence of plastic yielding on crystal orientation and lesser attention to the mechanism of flow after yielding has occurred. New work on aluminum and magnesium crystals is presented, and previous results obtained in this laboratory on magnesium1 are re-examined. STRESS DISTRIBUTION The problems involved in torsional deformation of single crystals are due entirely to the complexity of the stress distribution. In tension, if loading conditions are perfect, the shear stress on any particular slip plane is completely uniform over the entire area of that plane. In torsion, on the other hand, the stress on any selected plane in a particular direction varies not only from center to edge of the specimen but also around its perimeter. It is convenient to express the stress at any point in terms of t0, which is the shear stress acting at the surface of a cylindrical specimen on a plane normal to the axis and in a direction tangential to the cylinder. At point P of Fig. 1 this stress acts in the direction of axis 2 and is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. This stress can be resolved on any chosen slip system, and details are given in the Appendix. Let P be the point on the specimen surface where the stress is to be evaluated; P is defined by its angular distance A from an arbitrary reference line through 0 normal to the axis. his line is usually taken as the direction of incidence of the X-ray beam used to determine the crystal orientation.) Then the shear stress t, acting at P in direction Dona plane whose normal is N is given by Ts/TO = sin ? 0, cos ?d sin (?0, - ?) + cos ?, sin ?d sin (?d - ?) [2] where 0, and Od are the angles between N and D, respectively, and the axis, ?0 and ?d are the angles between the projections of N and D, respectively, on the transverse plane and the reference line through 0. By means of Eq. [2], the stress 7, acting in any given slip direction can be computed. In the previous work on magnesium1 only gross slip tangential to the specimen surface was considered, and this

Jan 1, 1963

By Perry Olcott .

THE Taka oil field is in the northern part of Titus and Franklin Counties, in north- eastern Texas. The small town of Talco, from which the field derives its name, is on the P. & Mt. P. R. R., about 15 mi. north of Mt. Pleasant, the county seat of Titus County. The oil field extends east and west from the town of Talco, the approximate center. In May, 1924, R. L. Cannon, while doing surface geology for the Humble. Oil & Refining Co., mapped the surface trace of this fault structure as evidenced by Upper Midway faulted down against Lower Midway. In the interval of sixteen years between the original surface work and the recent productive well completion, approximately eight wells were drilled into the Woodbine sand without success. The structure was well defined by those tests and all of the wells en-

Jan 1, 1936

By M. J. Bradley, P. H. Dike

THE art of melting nonferrous metals, in smelting, casting, and in compounding of alloys, is highly dependent on a knowledge of the temperature of the metal. This knowledge may reside in the experience and judgment of the melter, or it may be based on measurement by suitable instruments. It-is our purpose to discuss briefly the instruments available for such measurements, and more at length the present, practice in molten metals, without recommendation. In the limits of time and space allotted, we can do little more than mention the available methods of measurement that are directly applicable in this field. In the 1939 edition of the Metals Handbook, issued by the American Society for Metals, pages 285-310, there is a more extensive discussion of pyrometry than can be attempted here, which should be referred to for details we must omit. For reasons that will appear, thermoelectric pyrometry will constitute the major portion of our discussion of the subject, only limited attention being given to radiation or optical pyrometry. METHODS OF MEASUREMENT THERMOELECTRIC PYROMETRY A thermocouple consists of two dissimilar wires, or a wire inside a tube of a dissimilar material, joined together at one end, which is placed in the region or medium where the temperature is to be measured, while the other ends are connected through suitable lead wires to a voltage-measuring device, which may be a millivoltmeter or a potentiometer. An electromotive force is generated in the circuit, which is proportional to the difference in temperature between the hot junction and the junctions of the lead wires to the measuring instrument. If this latter temperature is maintained constant, the e.m.f. measured varies only with the temperature of the hot junction. Every thermoelectric pyrometer is calibrated for a particular cold-junction temperature such as 0°F., 32°F. or 75°F., but usually it is more practical to compensate instrumentally over the probable range of cold-junction temperatures than to maintain the junction at the particular temperature for which the instrument was calibrated. Thermocouple Materials Only a very few pairs of metals are in frequent use for pyrometric measurements. The most generally used are iron-constantan for temperatures up to 1500°F. in oxidizing and up to 1800°F. in reducing atmospheres and chromel-alumel, which may be used in oxidizing atmospheres at temperatures up to 2400°F. for intermittent service. The accuracy of the latter deteriorates rapidly at temperatures above 2200°F. Platinum vs. platinum-rhodium thermocouples may be used up to a temperature of 3000°F , but they are easily contaminated by slow absorption of

Jan 1, 1946

The following is an incomplete list of members and guests who called at Institute headquarters between Nov. 10 and Dec. 10, 1917. Harlan H. Bradt, Duluth, Minn. Lt. Geo. H. Morgan. Albert Burch, San Francisco, Cal. F. W. Osborn, Ajo, Ariz. J. A. Daniel, Institute of Mining & Metal- J. C. Ray, 2d Lt., 0. M. C., N. A. lurgy, London. A. E. Ring, Creede, Colo. Martin Fishback, Benson, Ariz. Geo. B. Rodgers, Dobbs Ferry, N. Y. E. L. Foucar, San Francisco, Cal. Forest Rutherford, Pueblo, Colo. I. A. L. Henderson, Institute of Mining & J. G. Scrugham, Reno, Nev. Metallurgy, London. A. F. Shurick, Forest Hills, L. I., N. Y. Jerome A. Hilbert, Santa Monica, Cal. Arthur C. Spencer, Washington, D. C. B. B. Hood, Chrome, N. J. Robert C. Sticht, Mt. Lyell, Tasmania. J. C. Hoyt, Jerome, Ariz. A. Perry Thompson, San Francisco, Cal. A. F. Kennedy, Duluth, Minn. J. B. Tyrrell, Toronto, Canada. Paul S. King, Wilmington, Del. Thor. Warner, Phoenix, Ariz. Alfred C. Levis, Golden, Colo. S. F. Wellman, Cleveland, 0. A. F. Lucas, Washington, D. C. Gardner F. Williams, San Francisco, Cal. B. E. McKechnie, Sharon, Pa. W. G. Woolf, Salt Lake City, Utah.' A. N. Mackay, Barranquilla, Colombia. C. W. Merrill, San Francisco, Cal. P. G. Beckett expects to be located in New York for some time, and may be addressed care of the Phelps, Dodge Corporation at 99 John Street. Corey C. Brayton and E. R. Richards have temporarily closed their San Francisco offices in order to give more time to their operations at Midvale, Utah.

Jan 1, 1918

By T. A. Rickard

RICO, in the southwestern corner of Colorado, is one of the productive mining centers of the San Juan region, so-called because its waters drain into the river of that name, which is tributary to the Colorado. The San Juan region includes the counties of Ouray, Hinsdale, San Miguel, Dolores, San Juan and Montezuma. It is traversed by a network of picturesque mountain ranges on whose lofty summits there rests perpetual snow. The region is peculiarly rugged, and, in the early days of its development, tested to the full the hardihood of the adventurers who first explored its can ions 111 search for gold and silver. A prospecting party, guided by Jim Baker, scout and trapper, penetrated in 1861 this part of the territory of Kansas. At that time the country was in the possession of the Ute Indians. In October, 1873, by the Brunot treaty, they ceded to the United States Government the richest mineral-bearing portion of their

Jan 1, 1897

By John K. Irwin

Friction hoisting has assumed a major role since its introduction to North America less than ten years ago. Interest was illustrated by a recent visit of the Adirondack Section of AIME to a new friction hoist at Chateaugay mine of Republic Steel Corp. at Lyon Mountain, N. Y. The 80-in. diam, 4-rope machine at Lyon Mountain is typical of modern friction hoists. The hoist is mounted on a structural steel tower without deflection sheaves.

Jan 10, 1963

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others developed on land by means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.' Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions, have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with the large features, and only by utilizing all the related sciences shall we

Jan 1, 1927