Search Documents

By Rodrigo Sanchotene Silva

Currently the industries of paint have directed their efforts on cleaner production of products that provide effective performance in corrosion protection of metallic materials. This work search introduce a new alternative of organic coating, without the presence of hazardous metals and replace equipments commercials used method of anodic protection for protection of oxidized metals. From this it, was produced Smart Paint (SP), consisting of Paint Acrylic Commercial (PAC) mixed the 1 % of binder, compound by the conducting polymer, Polyaniline Emeraldine Base (PAni EB) and plasticizer 4-chloro-3-methylphenol. The SP and PAC were applied to plates of carbon steel AISI 1010, with the aid of dip coat technique and then were subjected to drying for 48 h. The SP was characterized by thermals and physicochemical analyzes in order to verify possible changes in chemical properties of the ink produced, beyond perform electrochemical tests of Open Circuit Potential and Electrochemical Impedance Spectroscopy, employing equipment Potentiostat/Galvanostat Autolab PGSTAT302 Ecochemie, and aqueous 2 mol.L-1 of H2SO4. The results obtained allow us to state that the plasticizer does not alter the electrochemical properties of PAni and application of binder PAni EB to PAC does not alter the physicochemical properties of commercial coating. The binder PAni EB adds to PAC the capacity to induce the formation or maintenance of protective oxides in oxidizable metals submitted to harsh environments, method known as anodic corrosion protection.

Aug 8, 2018

By Francesco Toschi

The Special Bar Quality family comprises a wide range of steel grades, mainly requested by the automotive, energy and engineering sectors, for applications where significant performances are required (eg. stresses, temperatures, working cycles, etc.). To meet these requirements it is necessary to reach a precise control of both the mechanical characteristics and metallurgy structures along the whole production chain. For semi-product with large dimensions, such as equivalent diameters around 300 mm, this is traditionally obtained through a manufacturing route which comprises the casting in ingots followed by reheating, forging and rolling. After 2010, new processes were investigated and technologies developed to replace the ingot route with a continuous casting followed by controlled high-reduction rolling. In these processes a seamless integration of CCM with rolling is implemented so to obtain the precise control of material flow, applied deformation and working temperatures. By using the proper combination of rolling diameter, speed and applied reduction, a very good control of the metallurgy structure across the whole section can be obtained, so to also remove the internal discontinuities ("voids") generated during the continuous casting. These processes, which can be defined "forging-like", are applicable to several grades also with large semi-product dimensions (300 mm and more). Besides, removing the ingot route means increased yield and productivity, which is very beneficial to the economical management of the plant. An example of this "forging-like" process is represented by the high-reduction blooming stand installed by Acciaierie Venete in the Padova-Camin mill. This article describes its main concepts as well as its technology and process features.

Oct 30, 2017

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Rob van Opbergen, Edo Engel

The highly dynamic economic climate of recent years has tightened the operating envelope for steel producers world-wide. Steel producers continue to experience immense pressure to respond quickly to changing circumstances and the focus has shifted towards efficiency improvement and maximizing flexibility in operations. The ability to safely stop, restart and ramp-up production facilities has become essential. Establishing this level of flexibility, without sacrificing efficiency, requires sound process control, fit-for-purpose process management practices and solid know-how and experience regarding special situations in blast furnace ironmaking operations. The same business environment that demands this increased flexibility has made it increasingly difficult for steel producers to sustain sufficient knowledge about these situations. While many experienced, senior operational staff have retired, a new generation of ironmaking specialists has acquired its hands-on experience over more recent decades, during which these process situations have been much less frequent than before. Over the past 10-15 years, the requirement in the industry for external operational support during e.g. blast furnace blow–downs, salamander tapping and restarts after planned and especially unplanned stops, has become increasingly frequent. This article presents a number of these cases from a process management perspective as well as with regard to project organization and optimized cooperation between internal and external teams of experts.

Oct 1, 2019

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By Ron Webber

With the difficult economic challenges currently facing the steel industry, it is essential to perform a complete analysis when determining which rolls to purchase. A properly designed “Total Cost of Ownership” model can result in significant savings. This paper will review the costs associated with rolls in both Hot Strip and Cold Strip Mills. The multitude of factors that must be considered in performing a complete analysis for the roll purchasing process will be discussed. Models for both Hot Strip and Cold Mills will be presented. Examples where traditional analysis can lead to expensive, incorrect decisions will be presented.

Oct 30, 2017

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Sara Hornby

After almost half a century of experience in using DRI/HBI in electric arc furnaces (EAFs), and taking into account the decrease of natural gas cost in the USA, it is interesting to revisit some trends and controversial issues around this alternative iron source. This paper reviews aspects like the evolution of iron ore quality and its influence on EAF operation; DRI stockpiling and transport, regarding the risk for selfcombustion; optimum charge design; cold DRI/HBI charging (fifth hole, bucket, transporter); hot charging (ways and results); carbon content, metallization and silica in DRI/HBI, and its influence on EAF operation and performance; oxygen / carbon balance; chemical energy and DRI/HBI charge.

Aug 16, 2017

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Alisson Paulo de Oliveira, Altair Lucio de Souza, Jacson Morais Borges, Cleiton Arlindo Martins

A customized version of the Microsim-PM software for one Steckel rolling mill was built and adapted for specific mill parameters. The focus of this study is to use this model, which predicts the austenite grain size distribution evolution during rolling, to understand and quantify metallurgical issues happening during hot rolling. This will allow the steel mill to optimize the rolling process and chemical composition before the first industrial trial. Materials rolled for final thicknesses of 4.75, 6.30 and 12.5 mm of a carbon manganese steel and a microalloyed steel were selected to tailor the equations used by the model and to accurately reproduce the reality of the Steckel mill. This paper analyses the results from the customized model and compares them to mill data and final microstructure. Measured and predicted Mean Flow Stress (MFS) values are compared. After rolling, the material is subjected to accelerated cooling using laminar cooling. These cooling curves obtained from mill data are also considered to analyze the final microstructure characterized for all the cases using EBSD. The quantification of the microstructure allows for a better understanding of the relationship between chemical composition, process parameters and mechanical properties.

Oct 1, 2019