Search Documents

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

The theme of this paper is the development of-the project feasibility study which includes discussion of the work which is carried out in preparing the project feasibility study, the necessary evaluations and structures that are employed to ensure that not only does the feasibility study itself stand up to scrutiny and is sound, but also that the investment the company is proposing to develop, "the project", is an investment decision which will represent good returns to the company. This theme is particularly relevant when there are competing divisions within the company and only limited cash resources are available to make the correct investment decision. Thus various potential investments may be evaluated against each other to determine which project will be given the go ahead for development. This paper will particularly focus on the various investment analysis techniques that are used and discuss the work that is required in preparing the project feasibility study and specifically the interaction of the project team members and the thought process that must be undertaken to complete the project feasibility study. Finally comments will be made on tax planning issues particularly with respect to taxation of gold production to be introduced in January 1991. Some ideas are presented which may help and possibly improve the financial position of the projects being reviewed. Further, it is suggested that the thought process which goes with the financial engineering aspects of a resource project can be widened to take account of taxation issues and tax planning to ensure the rise of the project feasibility and hence the decision to proceed to development by the project sponsors.

Jan 1, 1990

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

An extensive laboratory grinding study was carried out on a magnetite ore in order to assess the grinding behaviour of magnetic concentrate and tail from low intensity magnetic separation (LIMS).The test work involved Bond ball mill testing, rod milling, low intensity magnetic separation (LIMS), and batch ball milling down to product sizes of around P80~25 microns. A total of 18 Bond tests and over 150 batch grinding tests and sieve sizing were carried out. Throughout the grinding tests, power draw was continuously monitored. The relationship between the grinding energy and product size was analysed using the conventional energy-size concepts. It was found that the Rittinger equation fits the experimental data well. However, Bond?s equation does not fit the experimental data well, and therefore a modified Bond equation was developed. Differences in grinding properties between the magnetic and non-magnetic component were analysed and compared to the bulk ore. It was found that grinding properties differ significantly and therefore separate grinding test work may be required for each grinding step in the magnetite ore beneficiation flowsheet. Keywords: grinding, iron ores, particle size, modelling.

Jan 1, 2010

By G A. Ekama

This paper describes a novel system for the biological sulfate reduction (BSR) of acid mine drainage (AMD) using primary sewage sludge (PSS) as carbon source in an upflow anaerobic sludge bed (UASB) reactor configuration. A UASB reactor was operated at a temperature of 35¦C and it received PSS (1875 mg/L COD) augmented with sulfate (1500 mg/L SO42-). The experimental results indicate that a high treatment efficiency was achieved at more than 90 per cent sulfate reduction at a liquid hydraulic retention time (HRT) of 13.5 h. In this study, the effects of various operational parameters were also investigated. The effect of a biomass recycle stream from the top to the bottom of the sludge bed was found to initiate rapid BSR from the bottom of the bed. Profile tests showed that effective and immediate sulfate reduction was achieved as soon as the influent entered the reactor. From these results, it can be concluded that the UASB configuration using PSS as energy source would be a viable method for the BSR of AMD.

Jan 1, 2009

By Paul R. Clark

Outline of Presentation ? Brief review of gasification and IGCC ? Polygenerationand its potential ? Why gasification today ? Major technology providers and their activities ? US initiatives ? Alberta Energy Resources and application of gasification ? CO2 management ? Advantages and barriers to gasification ? Conclusions

May 1, 2006

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987