Search Documents

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996

By Thomas Zukovich, Robert Morhard, Thomas Gelormino

The ExploTrack Explosives Tracking System is a sophisticated integration platform designed to track explosive products in both fixed locations and mobile environments globally, in real-time, on a 24/7 basis. The system utilizes active and passive RFID (Radio Frequency Identification Devices) installed within or applied upon explosives materials and explosives articles and incorporated within explosives packaging and logistic transport mechanisms. The system is designed for real-time inventory on an enterprise level and also across the globe providing explosives tracking, monitoring and explosives security from manufacturing throughout the logistics supply chain through use. The system can also track and monitor all known persons coming into contact with RFID enabled explosives materials and articles at the production level, at the magazine level, at the logistics level and to final use enabling a complete and real-time auditable chain-of-custody.

Jan 1, 2007

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Cínthia Toshimi Ogata

Processos de fundição de ligas de alumínio com altos teores de Mg são um desafio da indústria, uma vez que diferentes taxas de resfriamento ocorrem em geometrias diversas. Este trabalho tem como objetivo caracterizar a liga de alumínio AA5052 com variações em teores de Mg por meio de experimentos de solidificação direcional transitória, e compreender seus efeitos com relação a evolução de parâmetros térmicos, microestruturais, e propriedade mecânica. As leis experimentais de evolução do espaçamento dendrítico primário (?1) com relação a taxa de resfriamento resultam em: ?_1=640 ?T ?_L?^(-1/4) para a liga 5052 com 2,4%Mg e ?_1=300 ?T ?_L?^(-1/4) para a liga com 3,2%Mg. As leis de crescimento de espaçamento dendrítico secundário (?2) com relação a velocidade de solidificação resultaram em: ?_2=27 ?V_L?^(-1,1) para a liga 5052 com 2,4%Mg e ?_2=15 ?V_L?^(-1,1) para as ligas com 2,6%Mg e 3,2%Mg. Maiores teores de Mg na liga AA5052 proporcionaram uma expressiva redução no valor de ?2 para uma determinada VL. A evolução da dureza mostrou-se diretamente relacionada ao tamanho e a distribuição dos intermetálicos presentes, sendo ?2 o fator predominante neste controle.

Oct 30, 2017

By L. Ozdemir

An investigation was made to determine the mechanical properties of oil shale at elevated temperatures and confining pressures, the thermal properties at elevated temperatures, and to provide mathematical models for mine design for in situ oil shale retorting. A review of current activity in in situ retorting is included with a comprehensive list of references. Tests were run at temperatures from 20°C to 500°C and confining pressures to 1500 psi with shale of 10 to 30 gallons per ton. A major loss of strength occured in heating 140°C with a partial regain from 380°C to 500°C. Higher grade shale had lower compressive strength. Elastic properties showed large variations. Brazilian tensile strength showed a similar temperature sensitivity as the compressive strength. Equations were developed for each property in terms of grade, temperature and pressure. Thermal, electrical and acoustical properties showed anomalies through the temperature range. Creep is a major factor in overall deformation of heated shale. Oil shale was found to be an excellent insulator. Loss of pillar support area at 800 hours of heating would be about 10 percent. Good correlation was found between a finite element model using the developed properties and an in situ heater test.

Jan 1, 1981

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004