Search Documents

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By K. Y. Vasioutchkov, Y. F. Vasyuchkov, B. M. Vorobjev

In general a term "unconventional mining or "non-traditional mining technology" getting more and move familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in [Figure 1:] One of the greatest potential for coal utilisation during the beginning decades of on coming cetury is the synthetic fuel-gas derived from coal as a product of coal gasification. It is quite logical to enrich this gas before burning it with natural gas, that is methane, contained in coal measures. Thus it is reasonable to suggest a new concept of unconventional coal mining and utilization technology featuring integrated methane drainage with coal-gas combined cycle. Proposed unconventional technology of coal mining is characterized with: - opening up a coat deposit through boreholes, drilled from the surface and used for coalbed methane drainage as well as for coat gasification in situ; - aggregation of methane producing and coal gasification station on mining side with thermo power plant on the electric power generation side in one integrated industrial enterprise. The further improvement of the conventional coal mining technologies both surface and underground could give only insignificant results in economical, ecological and social aspects, but would not be able to provide basic requirements of the XXI-st century. Significant increase in economical efficiency, cardinal humanization of coal mining and basic improvements in environment protection would be achieved through introduction and implementation of innovative or unconventional coal mining technology. These considerations are applied on both coal production and coal utilization sides as far as coat based energy generation is concerned. Now a general opinion is widely spread that an application in the same manner of the traditional technologies of coal mining and electric power generation would inevitably cause further irreversible damage of the global eco-system, notwithstanding the certain environment protection measures being taken. Keeping the recent pace of the eco-system degradation the whole our civilization would be in danger. Thus the solution of this problem is to be found in developing, promoting and implementing in industry unconventional coal mining and modern advanced clean coal technologies. Coal reserves with favourable conditions at shallow depths are -being rapidly depleted in all countries with developed coal industry. So in nearest future more coat will be mined from deeper levels with higher operational expences and with lower labour productivity. For example in Russia only 20% of proven coal reserves can be specified in quality as easy mined reserves, i.e. coal reserves with a good minability. Unconventional (borehole in situ) coal mining enables us to mine difficult coal reserves, deposited under unfavourable geological conditions with higher economical and socio-ecological efficiency than that in conventional coal mining, in view of these the basic principles and concepts of coal mining and coal utilization for energy generation should be reconsidered taking into account the latest achievments in underground coal gasification/combustion, coalbed methane extraction, clean coat technology and advanced developments in environmental engineering. The authors have developed a new concept of ecologically clean and resource saving coal-gas electricity, protected by a patent of Russian Federation (1995). The main principles and technological features of these conceptual technologies are explained hereupon. It should be a break through into a coal mining technology of new generation, which is known as unconventional coal mining technology. Under current global energy policy, transection to the new generation of coal mining technology is inevitable. Now we are standing at the treshhold of the coat's regeneration based on integrated unconventional coal mining and innovative coal fueled electric generation technologies.

Feb 24, 1997

Hydraulic fluid power systems are advantageous whenever power output must be accurately and safely controlled. The load movers, cylinders, jacks, rotary actuators and hydraulic actuators in these systems can be made to smoothly and accurately start, stop, reverse, hold position or move steadily under heavy and variable loads or torques. Because hydraulic systems are simple, compact, reliable, and low cost compared to other power methods and because they can deliver controlled power anywhere on the machine to which a hose can be routed, they are a pan of almost every type of machine found on a coal mining section. Some of the functions they perform are positioning drill booms, driving drill pots on roof bolters, positioning curter booms, raising, lowering, and swinging conveyors, driving conveyors on continuous miners, raising, lowering, and applying sustained loads to longwall roof supports, and advancing the face conveyor and roof supports in longwall mining operations.

Jan 1, 1982

By G. Azimi, K. K. Varanasi1, A. T. Paxson, R. Dhiman, H. -M. Kwon

Hydrophobic materials that are robust to harsh environments are needed in a broad range of applications. Although durable materials such as metals and ceramics, which are generally hydrophilic, can be rendered hydrophobic by polymeric modifiers, these materials deteriorate in harsh environments. Here it is shown that a class of ceramics comprising the entire lanthanide oxide series, ranging from ceria to lutecia, is intrinsically hydrophobic. Their hydrophobicity is attributed to their unique electronic structure, which inhibits hydrogen bonding with interfacial water molecules. In addition, this work demonstrates that these ceramics sustain hydrophobicity even after exposure to high-temperature environment (1000 °C for 2 h in air). It is envisioned that this class of robust hydrophobic materials will have far-reaching technological potential in various industrial applications, where water repellency and dropwise condensation are desirable.

Jan 1, 2014

By María del Rosario González Moradas

El presente texto describe diversas técnicas de teledección como métodos para determinar alguna de las variables utilizadas desde el punto de vista geotécnico y que permiten una clasificación de los macizos rocosos. La metodología se ha basado en la búsqueda de las bandas más ventajosas a las combinaciones más adecuadas para la determinación de cada una de las variables geotécnicas citadas a través de las imágenes landsat 5 de dos épocas diferentes.

May 1, 2017

By G. Tiess, S. Mujiyanto

Indonesia is a fast growing democratic developing country comprising more than 17,000 islands, founding member of ASEAN and a member of the G-20 major economies. It is one of the most highly mineralised countries in the world, the mining sector playing a pivotal role in the country's economy. In 2001, the Decentralization Law No. 22/1999 came into force and caused a transfer of authority and responsibility from central to regional and local administrative governments. The new Mining Law of 2009 substituted its 40 year old predecessor, but lacked detailed regulations for its implementation. These were only issued in 2010, which lead to a period of great uncertainty for investors in the mining industry. The new legislation intends to foster domestic economic development, which may be interpreted as protectionist policy. For the development of a sustainable mineral resources policy, further endeavours will have to be made.

Jan 1, 2011

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014

By Robert W. Waytulonis

Mining regulations pertaining to the use of diesel engines were solicited from foreign countries with mining operations by the Bureau of Mines. Responses were received from 27 countries; the information received and U.S. regulations were reviewed, and those parts pertaining to the use of diesel engines in underground mining were synopsized according to the following subject categories: types of engines permitted, testing and certification procedures, fuel quality specifications, emission control requirements, procedures and frequency of testing exhaust gases, mine air quality and quantity (ventilation) requirements, procedures for testing mine air quality and quantity, and noise standards. All categories except the types of engines permitted and testing and certification procedures are summarized in tables. Contacts are provided for each country to facilitate inquiries concerning regulation revisions or interpretation.

Jan 1, 1987

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire's location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By C. Kennedy, S. Jensen

Traditionally, mineral processing plants are designed to achieve the highest recovery of valuable material with limited regard for the cost of managing waste products-both solid and water components. As an industry, we are confronting ever more stringent environmental standards and lower grade deposits requiring more intensive processing. The most profitable processing route can, in fact, lead to costly issues downstream. Issues or risks associated with waste management include water treatment and handling and storage of potentially acid generating material. The capital and operating costs of dealing with these issues are significant and should be considered as a consequence of plant design and optimisation. The authors of this paper are involved with a number of projects where process operation changes offer opportunities to mitigate risks associated with water and waste management. Examples of these changes will be discussed along with the estimated benefits to the value of the project and reduction of long-term environmental risks. Process changes include 1) the application of in-plant water treatment as opposed to dealing with the entire tailings management facility and 2) the potential to reduce metal leaching and acid rock drainage through the preferential liberation of carbonate minerals in the grinding process.

Jan 1, 2014

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004