Search Documents

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By Q. C. Reynolds

Keywords: Pyrometallurgy, plant, photography, GIS, satellite images, Google Earth Google Earth is a piece of software able to display an interactive three-dimensional map of the world, combining aerial and satellite photography with maps, terrain, and user-generated geographical information systems (GIS). Many structural features of the planet, both natural and man-made, are of great interest to the mining and metallurgy field, and in this paper a study is made of the current state of the art of data accessible by Google Earth.

Jan 1, 2006

By Daniel H. Israel

Indian tribes own a substantial portion of the West's minerals. More importantly, Indian reservations contain coal, oil and gas, uranium, and oil shale reserves in unusually large and unencumbered blocks. Many tribes are now prepared to intensify development of their large reserves knowing that they can offer energy partners the unique opportunity to develop major energy facilities free of overlapping local, state, and federal permitting authorities. The tribes, therefore, can offer mineral developers both substantial reserves and an unusual degree of freedom from a multiplicity of government regulation. In the past, Indians and energy companies enjoyed only partial success as business partners. Indian tribes lacked the resources and know-how to act as equal partners with large oil and gas and mining operators. The tribes relied on the Bureau of Indian Affairs (BIA) to initiate and execute reservation energy projects, and as a result the tribes never developed adequate tribal structures and the expertise to responsibly manage their energy resources. At the same time industry made little effort to understand and learn the laws, customs, and institutions existing on Indian reservations. To the contrary, industry found it easier to bypass the tribes and deal with BIA officials. But the situation has changed. In 1975 the tribes organized an effective coalition, the Council of Energy Resources Tribes (CERT), which recently acquired substantial federal assistance to bring the tribes a level of technical and business expertise that begins to equal that of industry. Because the tribes have changed the rules of the game, industry must now change and learn to work directly with tribal governments. A working knowledge of Indian law, practices, customs, and policies must be acquired by energy companies before beginning negotiations with tribal governments for development of reservation energy resources.

Jan 6, 1980

Plant for the production of sulphuric acid from pyrites flotation concentrates was commissioned at Cockle Creek during 1956, to meet increasing demands for commercial acid and superphosphate. Pyrite was chosen as raw material because of the uncertain supplyposition of imported brimstone and the desirability of utilising domestic sulphur.Desulphurisation of the pyrite is performed by two 40-ton per day roasters of the Turbulent Layer type operated under licence from the Badische Analin and Soda Fabrik (B.A.S.F.) organisation. These units are the first of their kind commissioned in the southernhemisphere. Pyrite is fed to the roasters in the as-received un-dried condition. Waste heat steam production is coupled with electricity generation within the plant. Sulphur dioxide is produced at comparatively high strengths and cleaned by conventional cyclone and hot electro-filter equipment.The acid unit has a capacity of 100 mono tons of sulphuric acid per day and includes cooling and wash towers, mist precipitators, a single stage drying tower, 4-pass oxidation section and absorption system.INTRODUCTIONSulphuric acid has been manufactured at Cockle Creek Works since 1913, when the first chamber nitration plant was commissioned. The raw material was brimstone roasted in Herreschoff furnaces. Since that time three additional chamber units have been constructed and have produced acid from brimstone, zinc concentrates, pyrites and -spent oxide, according to changing economic and supply factors.Three chamber units are still in operation. Contact processes have become increasingly important since the first Schroder-Grillo unit was commissioned in 1923. Six of these 5-ton per day units were operating in the mid-thirties, but have since been demolished. Two 15 ton Chemico hot gas contact units commenced operation in 1937 and 1938, and although modified, are still in service.The increasing demand over recent years for sulphuric...

Jan 1, 1957

By Dennis S. Kostick

Salt is a universal mineral commodity used by virtually every person in the world. Although a very common mineral today, at one time, it was considered as precious as gold in certain cultures. This study traces the material flow of salt from its origin through the postconsumer phase of usage. The final disposition of salt in the estimated 14,000 different uses, grouped into several macrocategories, is traced from the dispersive loss of salt into the environment to the ultimate disposal of salt-base products into the waste stream after consumption. The base year for this study is 1990, in which an estimated 196 million short tons of municipal solid waste was discarded by the U.S. population. Approximately three-fourths of domestic salt consumed is released to the environment and unrecovered while about one-fourth is discharged to landfills and incinerators as products derived from salt. Cumulative historical domestic production, trade, and consumption data have been compiled to illustrate the long-term trends within the U.S. salt industry and the cumulative contribution that highway deicing salt has had on the environment.

Jan 1, 1993

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical of these processes is that the amount of slag is quite high. The role of slag for the process is thus essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2 based with minor contents of CaO and CrOx. Slags in the FeMn process are principally similar, originating from silicate minerals but can have quite large composition range depending on the manganese ore and its gangue minerals. Characteristic of the FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOx in slag are not only divalent oxides but also contain some higher valent of Cr3+and Mn3+, respectively. In FeMn production conditions the slag consists mainly of Mn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexist in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. The thermodynamics of slags in ferroalloys, production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties

Jan 1, 2004

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks ("magnetite" concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002