Search Documents

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27'6" diameter, 78'O" deep Brandywine Street - 30'6" diameter, 88.6' deep Ellicott Street - 33'0" diameter, 110'0" deep

Jan 1, 1985

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By M. Hagfors

On the underwater testing of explosives, the measuring system consists of water filled test pond, tourmaline based pressure sensor, measuring cable and measuring unit, which supplies the DC current to the pressure sensor. Depending on the length of the measuring cable, it is always possible that some signal damping may occur in case the measurements are carried out without the signal amplifier to keep the measuring system as simple as possible. Therefore the length of the measuring cable should always be as short as possible.

Jan 1, 2006

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

During recent years there has been a marked increase in the use of explosives in Queensland coal mines. Delay detonators have been introduced and their use has extended with the wider application of mechanised methods of mining.The need for careful study of the characteristics of delay detonators is stressed so that the advantages of simultaneous firing, from the points of view of safety and efficiency, may be obtained. With their use new potential hazards are introduced. These hazardsare considered and means whereby the overall safety may be improved are discussed.The increase in the number of misfires since the introduction of delay detonators is shown and the examination of misfired detonators is described. Lessons to be learned! from these misfires are noted and details are given of the essential requirements for safe and efficient blasting using delay detonators.INTRonUCTIONOne of the aims of mechanization in coal mines is to reduce the physical effort applied to the winning of coal. Explosives play an important part in achieving this and, following the introduction of power borers for the drilling of shot-holes in Queensland coal mines, much of the arduous work associated with coal getting has been eased. During recent years there has been a marked increase in the consumption of explosives, as shown in Table 1, and it must be the aim of all to use these explosives safely and efficiently. That there are dangers associated with the use Of explosives cannot be denied. The shotfiring operation is fully covered by legislation and, being under the control of one man, shQuld be capable of being carried out with a high degree of safety. The main source of accident appears to be the failure to take proper cover and this has resulted in...

Jan 1, 1958

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

The Harmonious Design on the Beneficiability for the Pt-Pd Ores Containing High MgO Gangue in Yunnan

Sep 13, 2010