Search Documents

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

By T Nassis, H M. Nel, T du Toit

Assmang Khumani Iron Ore Mine is exploiting the iron ore deposits that can be found in the Bruce-King-Mokaning farm areas in the Northern Cape, South Africa. The Bruce, King and Mokaning (Khumani) deposits are approximately 10 km south of the town Kathu, adjacent to the Sishen Mine. Assmang Limited is jointly owned and controlled by African Rainbow Minerals Limited and Assore Limited.Measurement, calculation and trending of plant throughput and chemical ore properties are critical in maintaining a successful beneficiation operation due to these values forming the basis of decision-making and thus promotion of efficient ore extraction. The Khumani management and engineering information system (MEIS) supplies information on key process parameters to an operational team and is required to do so within an optimal time frame, for maximum impact.Diverse data is put into the MEIS from multiple specialist systems, with interfaces that require manual intervention. Manual intervention is resource and time intensive to the point which limits the effect on the process and decreases the potential for value addition.Automation of interfaces decreases resource and time requirements, standardising plant wide data sources and providing the opportunity to provide specialist system data to decision-makers in a timely fashion, resulting in maximum impact on the process output.Engineering and metallurgical management systems were interfaced at Khumani Iron Mine by means of an automated table which facilitates the transfer of production data validated within the engineering system as input to the metal accounting system. This interface effectively assigns a master to each specialist data set employed for decision-making and delivers accurate process parameters to the production team within an optimal time frame, resulting in increased potential to improve beneficiation efficiency.CITATION:Nel, H M, Nassis, T and du Toit, T, 2013. The role of metallurgical and engineering information systems in the optimisation of iron ore beneficiation processes, in Proceedings Iron Ore 2013 , pp 453-458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By A. R. Biggart

Twenty-sixth Sir Julius Wernher memorial lecture, presented at the Tunnelling '94 symposium held in London, 5-7 July 1994. In describing 18 projects with which he has been involved over a period of 36 years, the author aims to illustrate how technological change and an increase in scientific knowledge have influenced tunnelling practice, which he nevertheless maintains does continue to be an art. Tunnels discussed are: the Silver Street, Blackfriars, Whitechapel, St. Paul's and Waterloo Post Office tunnels, 1958-1969; metro tunnels on the Victoria Line, London, 1962-1970; the introduction of tunnel boring machines (TBMs), 1971-1978, in the Empingham reservoir diversion tunnels in Rutland, the bentonite tunnelling machine experiment at New Cross, the Southern tunnel water main section of the London Ring Main and the Warrington sewer in Cheshire; tunnels in rock 1975-1981, for the Lune Wyre and Megget Manor aquaducts, Weymouth sea outfall and Bristol interceptor sewer; Priestley TBM tunnels 1969-1982; the Greater Cairo wastewater project 1983-1987; Anacostia River crossing, Washington DC 1985-1987; the Channel Tunnel 1987-1992; and the Storebaelt eastern tunnel in Denmark, 1992-1994.

Dec 1, 1994

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By Michael Sokaski

The Cliff Springs prospect in the northern part of the Slate Range Wilderness Study Area (WSA) contains only minor amounts of gold and silver. Clay near this prospect contains insufficient aluminum to be of economic interest, although alunite claims are recorded in the vicinity. Mineralized rock at the Crescent Mine adjacent to the WSA contains gold, silver and lead occurrences. The host rock may be present in the extreme southwestern part of the WSA, which is covered by alluvium. Substantial sand and gravel deposits are present but these occurrences are remote from markets. Much of the USA is underlain by volcanic rocks and alluvium and consequently the mineral resource potential there remains unknown.

Jan 1, 1983

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

Thickener Modelling - Incorporating Shear Effects

Sep 13, 2010

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950's and 1960's, and improved truck load capacity and efficiency were also important.

Jan 1, 1977

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002