Search Documents

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

By A. Esterhuizen, S. Essack, H. Joubert, N. Fowler

Tenova Pyromet has developed innovative technologies for copper smelting and electric slag cleaning furnaces. Based on client feedback and requirements, innovative designs have been developed to address key design areas and improve furnace reliability, operability and hygiene. These developments include the NovaLance™ lance system to prevent lance bending on top submerged lance furnaces, the SlagFlo™ slag tapping flow control device to better control bath levels and tapping rate for granulation, and an electrode seal for improved sealing directly onto the electrode casing to allow water-cooled electrode components to be located above the furnace roof. The potential application and benefits of these innovative designs are discussed. INTRODUCTION Tenova Pyromet has a long history in the engineering and supply of innovative electric furnace and related equipment for the base metals and platinum industries. Recently Tenova Pyromet has used its furnace equipment design experience to engineer innovative solutions for top submerged lance (TSL) furnaces, and potentially other furnace technologies. These equipment design solutions are developed to address specific operating challenges and operator requirements. Three of these innovative equipment developments are discussed in this paper. First the NovaLance™ lance technology to prevent lance bending during operation in TSL furnaces, such as used for primary copper smelting, is described. Lance bending has been identified as a significant problem for TSL furnace operators as it causes down time and affects furnace availability. The SlagFlo™ device to control the slag flow rate during tapping has been developed based on specific requirements in the mineral wool industry. The SlagFlo™ device can be used to control slag bath levels in primary smelting, converting and slag cleaning furnaces for base metals including copper. In addition, it can be remotely activated for the safe closing of slag tapholes located upstream from a water granulation system. Finally, Tenova Pyromet developed an electrode seal that seals directly onto an electrode surface. This is a special requirement related to base metals and platinum electric smelting and slag cleaning furnaces where furnace operators prefer to keep the water-cooled electrode equipment above the furnace roof. The seal can be used to seal directly onto the potentially hot and uneven surface of Söderberg, pre-baked and graphite electrodes.

Jan 1, 2019

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

Jan 1, 1993

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By Irvin G. Burough

ANDROS INCORPORATED has designed, manufactured and delivered four handheld C02 DETECTORS and three handheld CH4 DETECTORS. These instruments are for in-mine safety use. The DETECTORS incorporated an NDIR optical/electronic analyzer design in which exceptional zero stability is achieved by pressure modulation of the sample gas. This eliminates the need for daily calibration. This stability and the miniature design (2.5" x 4.5" x 4.5"; 4.5 lbs) of the C02/CH4 DETECTORS provide practical instruments suitable for routine safety inspections. This report includes the theory and design of the instruments as well as studies of gas-pressure modulation by a piezoceramic-driven Helmholtz resonator.

Jan 1, 1979

Since the comprehensive review of the Persian fields presented by Sir John Cadman last year, operations have proceeded normally. No developments of especial importance fall to be recorded and it remains only to bring up to date the full information given at the beginning of 1933. Controlled production from the Masjid-i-Sulaiman and Haft Kel fields has been maintained at slightly higher rates than during 1932. The figures for the past five years are as follows: These represent crude oil and products piped to the coast but exclude products reinjected into the reservoir, a process that has been in continuous operation at Masjid-i-Sulaiman during the period under review. The systematic delimitation of the Haft Kel field has been continued during the past year and results have been sufficiently encouraging to justify the inception of a wider scheme for distribution of production. Drilling has been resumed recently in the Persian sector of the Naft Khaneh field, and preliminary survey work is in progress for the selection of a site for a refinery at Kermanshah arid the construction of a connecting pipe line. Investigations in connection with the scientific control of reservoir were dealt with in considerable detail in last year's review. This work has been steadily pursued during 1933 and certain of the investigations have been the subject of papers presented to the World Petroleum Congress held in London in July of last year.

Jan 1, 1934

By J. A. Singmaster

IT will perhaps be wise to define my terms in begin-ning to talk about my subject, especially so where the popular and commercial terminology are as con-fused as they are in the case of zinc. While our French friends know zinc by its true name, and we find Balzac, Daudet, and other literary celebrities using it correctly in their novels, it is quite the contrary in English, particularly here in America. The quotation of a definition for zinc recently appearing in one of our leading technical magazines, "zinc is the place where they wash the dishes," will emphasize the difference. Zinc suffered in the first place by becoming an article of commerce long after its alloys with copper were in common use under the name of brass. Then again, when the art of zinc coating iron and steel objects was commercialized, we called it galvanizing, which is really a meaningless term. The French and Germans use the obvious terms-zinguerie and verzinken-for the opera-tion. Since these two uses of zinc, brass making and galvanizing, have been by far the largest consumers of zinc, is it any wonder that the popular knowledge of zinc is as vague as it is? In fact, since the disappear-ance of the sheet of zinc along with the parlor stove, the zinc-lined bath tub and refrigerator, there has been little popular contact in this country with the undis-guised metal zinc. On the Continent, where zinc has been used for over a hundred years under its real name, particularly for roofing and building purposes, the situ-ation is quite different. It is quite refreshing to turn for a moment to the contrast offered by my friend, Dr. Merica's specialty, nickel. They put 2 or 3 per cent of it into steel, and we have nickel-steel, or a larger amount into an alloy, and we have nickel-silver. To be sure there is no silver there, but what need that matter, nickel is used in the alloy and is first in the name. They plate with nickel and call it nickel-plating, no galvanizing about that. And, finally, they take that noble coin which admits us daily to underground New York, composed of three parts of copper and one part nickel, and get away with nickel as its popular name.

Jan 6, 1927

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008