Search Documents

By Wils L. Cooley

Although electric utility companies have been active in grounding and bonding within substations, the mining engineer or mine electrical engineer is not involved to the extent that he can be fully up-to-date on the most effective practices for substation construction. The coal mine power system is grounded in a fundamentally different way from most other industrial power systems and is subject to considerable Federal and State regulation. At this time, there is little information that is directly applicable to the mine situation, especially if the substation must be built in an area of limited size or in low-conductivity earth. The objective of this guide is to provide specific engineering information to the mining; industry. Using as little theory as possible, it was written to be general enough to cover most substations, but specific enough to provide direct help with each substation. It will attempt to recommend practice that is in agreement with present Federal rules and regulations.

Jan 1, 1980

By S Yuen, T Rana, S Khan

Many open pit mines require dewatering or need aquifer depressurisation systems to manage mine water inflow and/or mine floor stability. In many instances these mining operations impact on regional groundwater resources and therefore access to these resources by other users.As such potential exists for mine development to be hindered or even blocked by groundwater legislation that aims to prevent declining groundwater levels and demonstrate equitable use of a regional groundwater resource.There is a need to manage aquifer systems during and after the mining operations, and in some cases stresses on the aquifers and associated ecosystems may be elastic and can be managed with minimum impacts or reversed once the mine ceases to operate.This paper uses the Gippsland sedimentary basin, with a history of declining groundwater levels and mining and petroleum production, as a case study to pose the question: Should period of mining operation, aquiferÆs storage capacity and its ability to recharge be concurrently considered when granting groundwater abstraction and mining licenses for prospective mine development?It further examines that by utilising an aquiferÆs storage capacity and demonstrating an understanding of aquifer system hydrodynamics during and beyond the life of the mine (time), the approval process for groundwater abstraction and associated cost of statutory monitoring may be made less onerous.

Jan 1, 2009

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By Fernando Romero Lage

The purpose of this paper is to analyze detailed crushing and screening configurations and the interrelationship as they relate to mass flow balance, operating efficiency, plant availability and final production. The entropy of ore bodies limits the standardization of crushing and screening plants, however, consideration for a continuous and sensible assessment of the mass flow balance of the circuit will yield the best achievable results. Since energy costs have continuously risen in the last few years, it is imperative that these circuits offer low power requirements and low operating expenses. The paper will detail how the efficient implementation of continuous mass flow balance in the application of crushing and screening plants will generate quality improvement and process improvement, which will translate into bigger production and energy savings.

May 1, 2010

By O. F. Oxtoby, J. E. Olsen, M. W. Erwee, Q. G. Reynolds

"The extraction of molten products and wastes through smelting furnace tap-holes during the tapping process is a complex procedure involving many coupled thermophysical effects. Insight into the fluid flow behaviour in such systems can be gained by using computational mechanics tools to build highfidelity models of the fluid flow and other relevant physics. Previous work using such models indicates that the nature of the flow in the tap-hole, as well as operational parameters such as the tapping flow rate, depends strongly on the properties of the material being tapped and the geometry of the tap-hole channel. Additional complications arise when multiple fluid phases (for example, slag and metal) are present simultaneously, when porous coke beds hinder flow to the tap-hole entrance, and when the geometry of the tap-hole changes over time due to cycles of wear and repair. In the present work, challenges with the coupling of phenomena such as multiphase flow and porosity into computational fluid dynamics methods for tap-hole modelling are discussed in the context of electric furnaces used for ferromanganese production. Qualitative and quantitative results of computational models of flow through tap-holes are presented and compared as a function of material parameters to determine sensitivity effects, and in response to operational parameters to determine typical process behaviour over the duration of a tap. IntroductionPyrometallurgical production using electric furnaces accounts for substantial portion of the world supply of ferroalloys and other strategic materials (Degel et al., 2015). A range of different furnace designs may be used depending on the metallurgical process, with circular three-electrode submerged arc furnaces (SAFs) powered by alternating current being the most common for commodities such as ferromanganese and silicomanganese (Olsen, Tangstad, and Lindstad, 2007).As shown in Figure 1, manganese furnaces typically operate with a deep charge consisting of an upper layer of loose burden (onto the upper surface of which is fed solid raw material), a molten slag layer partially or completely filled with unreacted carbonaceous reductant (generally metallurgical coke), and a molten metal layer which settles to the bottom of the furnace due to its high density. The solid particles present in the slag and burden layers form porous beds which hinder the fluid flow of molten process material and gases inside the furnace (Olsen, Tangstad, and Lindstad, 2007).In order to remove material from the furnace during normal operations, a single tap-hole is built into the sidewall of the vessel near to the level of the hearth. Tapping involves removing both slag and metal phases through the same tap-hole channel, which makes tap-hole design, operation, and maintenance particularly complex. In the case of processes such as ferromanganese, which operate with no external gas injection or open arcs present at the furnace electrodes, flow of material out of the tap-hole is driven primarily by the hydrostatic pressure generated by the weight of the solid and liquid phases above the tap-hole."

Jun 1, 2019

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

An experimental study of the soil mechanics of brown coal showed that brown coal consolidates in the same manner as does a clay and that the theory of consolidation for soils may be applied to brown coals. Moisture content is a function of the coal type, the existing effective stress, and the stress history of the coal.The effective stress in a brown coal seam is a function of the overburden pressure, the pore stress and tectonic stresses. Stress history may be deduced from geological evidence and determined by consolidation tests. Application of these principles to the brown coal seams of the Latrobe Valley shows that the distributions of natural moisture contents are consistent with consolidation.INTRODUCTIONThe nature and geology of the brown coals of Victoria, particularly of the Latrobe Valley, were discussed in some detail by Edwards (1945, 1948), Thomas and Baragwanath (1949) and Gloe (1960). A salient feature of these studies was the distribution of moisture contents in the brown coal seams. Recent experimental work, part of a soil mechanics study of the structure and strength of brown coal, showed that moisture content variation is a reflection of consolidation phenomena in brown coal and application of the results to .field condItions verified and modified the conclusions of Edwards in his pioneer work. Further detail of this experimental work is recorded elsewhere (Rosengren, 1961).EFFECTIVE STRESS AND CONSOLIDATIONEffective stresses in soilsA saturated soil is a two-phase system, consisting of a compressible skeleton of rigid soil particles and pores filled with water, an incompressible fluid. (In this context, the terms compressible, incompressible, and rigid are relative only and refer to orders of magnitude). If this system is subjected to stress we define...

Jan 1, 1963

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By Alexander J. Verstraeten

Work started on the building of the Amsterdam Concert Hall in 1880 by driving over 2000 wooden piles of 13 m on which foundation-beams out of wood and brickwork were made. During construction the design was changed. This was due to the latest German developments, requiring double walls instead of single, so that the space in between could be used for ventilation and heating. Therefore the pile load, originally designed at approximately 100 kN, increased even to 170 kN for some piles, causing settlements and unacceptable cracks in the brickwork. Settlements of up to 18 cm were measured. In 1985/1986 around 400 vibration-free Tubex-displacement-piles were installed under the Concert Hall, with a shaft of 0355 mm, a pile shoe of 0560 mm and a pile length of approximately 18 m. After these Tubex piles had been installed they took over the complete weight of the whole building, thus eliminating further settlements and damage. 95% of all the construction activities took place while the concerts went on. The chosen solution also made it possible to create a new basement under the Concert Hall as an extension for dressing-rooms etc.

Jan 1, 1987

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By L. B. Pankratz

Thermodynamic data on carbides, nitrides, and other selected substances were reviewed, evaluated, and compiled at the U.S. Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, -(G° - H298)/T, ?Hf, ?Gf, and log Kf are given in tabular form. Cp°, H° - H°248, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1994

By Xu H.

In recent years, the mineral applications dealing with more complex data in distributed environment have grown rapidly. Many mineral and mining organizations have to organize internally and globally distributed manufacturing and experiment sites, which share the roles of databases and other multi-services like software programs. Thus, there are commercial and technical pressures pushing the mineral software vendors to move their current service toward Web service. XML has gained wide acceptance for representing, storing and transferring structured data and documents of many kinds, especially in scientific communities. However, so far there is no such a Markup Language in mineral industry. A XML-based uniform encoding, which is called MineML(Mineral Markup Language), is proposed and developed in this project. The framework of the MineML specification is created. MineML will play the role as shared protocols within mineral domain for archiving, transferring the multi-nature data between the software packages on the desktop over the Internet and sharing the services between users at different sites. Inspired by MLA’s (Mineral Liberation Analyser, JKMRC, University of Queensland, Australia) Mineralogical Data Presentation Program, a proof-of-concept prototype of Web Service is developed here to validate and demonstrate the MineML specification. Certain strategies, specific technologies and tools are adopted to create such an environment. To accomplish that, a set of experimental MineML documents including correlated XML, XSD (schemas) and XSL(stylesheets) documents have been elaborated for archiving, presenting and transferring the mineralogical data information, with the persistence on flexibility and extensibility for generic mineral and mining data handling.

Jan 1, 2003

By E Rojas, C Pardo

The exploitation of primary ores using cave mining caused new challenges at the El Teniente mine that required changes to a number of conventional cave mining practices. For example, in the 1970s and 1980s, panel caving was introduced to manage certain geotechnical and operational conditions. Today, El Teniente mine is facing new challenges associated with deep cave mining and establishing its New Mine Level (NML) project, which is located 240 m below the Esmeralda operating cave.The engineering and development phases for this new project have been largely based on experience and lessons learned throughout the history of primary ore exploitation at El Teniente mine, particularly knowledge about seismicity control, the management of collapses and operational practices. For example, previous experience demonstrated that seismicity could be managed by preconditioning using large-scale hydraulic fracturing (HF). HF has been systematically applied in the column of ore above the undercut planned for the NML project and below the production or extraction level, where the main ventilation and haulage infrastructure are to be located.This paper discusses how this has been achieved and is based on previous experience of preconditioning using HF, which has been applied in the selection and management of exploitation techniques and associated planning strategies and design parameters for the NML project.CITATION:Pardo, C and Rojas, E, 2016. Selection of exploitation method based on the experience of hydraulic fracture techniques at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By Gary R. Peterson

In order to determine the potential availability of alumina to feed U.S. aluminum smellers, the Bureau of Mines evaluated 39 domestic mines and deposits of bauxite, alunite, and high-alumina clays and found that substantial increases in alumina prices would be necessary before nonbauxitic deposits could become competitive with bauxite. As part of the study, a price-tonnage relationship was developed indicating the quantity of alumina that could be produced from known deposits at various alumina prices and at a 15-pct discounted cash flow rate of return on the required capital investment. All capital and operating costs were calculated in August 1980 dollars. The domestic bauxite reserve base comprises three operating bauxite mines in Arkansas containing some 15.6 million metric tons of recoverable alumina (A1203). Ferruginous bauxites, clays, and alunites fall into the subeconomic category of identified aluminum resources, which, at the demonstrated level, contain over 4,000 million metric tons of alumina that are estimated to be recoverable. Analyses indicate that, at the demonstrated resource level, a total of some 15.6 million metric tons of alumina, all from three active Arkansas bauxite mines, is recoverable at a 1980 price of $0.12 per pound ($264 per metric ton) of alumina. A price of approximately $0.26 per pound ($573 per metric ton) of alumina would be required for production of the total U.S. resource. Thus, unless new technological breakthroughs occur that could make alternate sources of alumina competitive with bauxite, U.S. dependence upon imported bauxite will continue to increase.

Jan 1, 1981