Search Documents

By William J. Purdy

Successful design, operation and completion of a surface waste management facility for a diamond mine located in Canada?s northern environment requires careful planning to minimize short and long term environmental impacts. As part of the mine development application process, best practice standards were applied using conventional engineering to reduce the environmental effects of the mine waste facility at the Snap Lake Diamond Project. This paper presents the design criteria, site conditions, material characteristics and engineering management objectives considered for optimization of the development plan. Insight into the engineering analyses, development alternatives, monitoring program and reclamation strategy plan to be undertaken during mine operations to provide opportunity for adaptive management and to minimize environmental impacts is provided.

May 1, 2004

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By AIME AIME

TWO days of solid discussion, with barely time out for meals, characterized the Tulsa meeting of the Petroleum Division. It was preeminently an earnest gathering devoted to technical matters. Sessions were held in the Crystal room of the Mayo Hotel with luncheon served each day in the back of the same room so that talk of methods, while slightly less formal, extended right through the lunch hour. Thursday evening the Committee did provide a little relaxation in an informal dinner at the Tulsa Club where, after a brief musical program and an amusing skit by the local Herman the Great, brief addresses in non-technical vein were made by President Farish and Vice-president Rice of the Humble Company, Henry L. Doherty of Cities Service, Secretary. Bain of the Institute, and others. The presence of leading executives of a number of the oil companies at the dinner and the sessions, and the cordial approval they expressed of the work of the Division were especially gratifying. The total registration was 215 with 100 at the dinner and 70-to 80 lunching together each day.

Jan 1, 1930

By Hongfa Hu, Stavros A. Argyropoulos, Stephan Ferenczy

"Physical as well as mathematical modeling was carried out to investigate the exothermic mass transfer in liquid metal systems. In these systems, the exothermicity induces unique heat, mass and momentum transfer phenomena. Moreover, these phenomena are deeply coupled and they are further complicated by the presence of a moving boundary.In the physical model used, ice cylinders were immersed into sulfuric acid solutions, because the intermixing of ice with sulfuric acid is very exothermic. In this low temperature system, velocity and temperature measurements in the sulfuric acid were made as well as measurements of the ice melting in the sulfuric acid.The mathematical model developed solved simultaneously the heat, mass and momentum equations numerically, utilizing the control-volume finite difference approach. The enthalpy method was adopted to track the moving boundary. Predictions made by the mathematical model were in close agreement with the results obtained by the physical model.The results from the mathematical model were further validated with experiments involving high temperature liquid metals. Specifically, data were obtained in an experimental setup involving (a) dipping silicon cylinders into high carbon liquid iron and (b) dipping nickel cylinders into liquid aluminum. Results from these experimental studies supported the predictions of the mathematical model."

Jan 1, 1999

Research personnel from the Bureau of Mines, a representative of the Mine Safety and Health Administration, and research contractors for the Bureau of Mines met with other Government and industry representatives at three seminar locations in December 1980 to discuss the findings and products of Bureau research on mine safety training. The research program is aimed at providing assistance to the mining community in its efforts to reduce industrial-type, human-error accidents through research establishing performance based methods and media for employee training. Research emphasis is directed toward development of baseline materials and instructional models; development of methods for structuring and evaluating health and safety, supervisory, and occupational training; and the continued investigation and application of current learning and simulation technology that could significantly enhance the effectiveness of training opportunities.

Jan 1, 1981

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By W. M. Peirce

COAL'S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994

By S. Auger, S. McDonald, K. Ward

"This preliminary paper provides a summary of lab and mill flotation investigations into the copper collector at two Canadian operations. The orebodies illustrated in these studies both contain mainly copper and zinc with uneconomic quantities of lead. Silver is also present as a secondary precious metal.Each mill has advanced to the extended mill trial stage with Uniflot SP129 as the sole copper collector. The preliminary metallurgical results have indicated higher copper circuit zinc and lead rejection is possible as shown in Case Study #2. In Case Study #1, improved zinc circuit metallurgy has been realized during all the Uniflot copper circuit collector trials. A slight increase in silver recovery has also been observed in the extended trials at both operations. INTRODUCTIONThe Canadian base metal industry is presently going through a rationalization period in response to low metal prices and low grade ore bodies. The response from flotation mills has been to reduce costs by incorporating new technologies such as energy efficient large cells, low moisture pressure filters and low steel consumption SAG mills. Other optimization strategies have been incorporated to get better metallurgical performance such as improved process control and monitoring techniques.The newer flotation plants have embraced many of the latest equipment innovations but they continue to incorporate off-the shelf reagents like xanthate and methylisobutylcarbinol (MIBC) . New collector chemistries have been mostly unsuccessful. Our approach incorporates the best of the old and new chemistry into proprietary formulations that match the application. We have found most single chemical formulations cannot meet the demands of the optimized modern flotation plant."

Jan 1, 1992

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

Three main divisions of the Proterozoic are recognized in the North-West Division of Western Australia. These are referred to, in order of decreasing age, as the Mt. Bruce Supergroup, the Bresnahan Group, and theBangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed, and a brief geological history of the whole area is presented.

Jan 1, 1966

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities in and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years.

Jan 1, 1933