Search Documents

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

Today computers are accepted as a standard item in industry and they perform a variety of tasks over a wide spectrum of activities from mine planning and CAD to data processing and spreadsheet work. However many problems particularly in the. area of decision making where there are no clear mathematical models available and usually the output or answer is dependent to some extent on a heuristic approach, don't lend themselves to conventional solutions using standard procedural algorithms. Recently a number of techniques have evolved primarily from the enhanced capabilities of modem equipment, which are capable of solving these problems. This paper is a brief overview of these rather unconventional developments of computer technology in the area of artificial intelligence with reference to their application in mining.

Jan 1, 1993

Rational decision making is generally perceived by managers of operations to be a delicate process of committing large sums of money and putting other people's life at risk. Consequently most managers may argue that the decision process requires good judgement, intuition and extreme caution; and not one easily made through the use of fancy mathematical algorithms and computer programs. The advent of artificial intelligence and expert systems in the computer industry combined with recent technological innovations in mathematical and economic problem solving is sure to change this perception. PARETO OPTIMALITY is an economic and a mathematical optimisation concept applied to solving real life operational problems; and one that the current volatile economic forces would require managers to employ because it is virtually real. REALISMM is a computer software package developed using the principles of Pareto optimality, dynamic programming, optimal clustering of information and decision maker interaction to generate decision maker preferred solutions. REALISMM has scope for artificial intelligence and expert systems application for cases where the decision maker is unsure about his objective preferences.

Jan 1, 1993

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By William H. Hamilton

INTRODUCTION It was not very many years ago that tunneling machine manufacturers spent considerable time trying to convince contractors and mine operators of the advantages of mechanical tunnel boring over conventional drill and blast methods. Today there are few doubters left. There is universal agreement that, not only are tunneling machines here to stay, but the ratio of bored rock tunnels to blasted rock tunnels is increasing at an accelerated pace, and within the next twenty years I predict almost all tunnels will be bored by machine. I believe we are today at a very important mile-post in the development of tunnel boring systems. Felix Gaye stated in his recent article (1) "It is important to disseminate between the efficiency of cutting tools and the overall efficiency of the boring operation". Mechanized tunnel boring in the past placed almost total emphasis on the rock cutting and boring ability of the tunneling machine. With advancements in technology and better solutions to the problems of rock fracture, steering control, and structural design, the emphasis today can be placed on the total-system concept. Tunneling machine design, as one of the key elements in the overall system, presents many problems that are not totally solved today. These design problems are, in the most part, not related with rock fracture, but rather with criteria associated with the over-all operation.

Jan 1, 1997

THE nature of the ore deposit of the Broken Hill line of lode is such that it can be broadly divided into two the calcitic and siliceous ore bodies. The principal minerals occurring in these ores are: Galena, sphalerite, pyrite, arsenopyrite, chalcopyrite, pyrrhotite, calcite, rhodonite, garnets, feldspar, fluospar, quartz.Whilst these minerals persist in both classes of ore, the following typical analyses of Broken Hill South Limited ore bodies will give some indication of the disposition with regard to each:

Jan 1, 1928

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit&apos;s new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

The Rosebery and Hercules mines, situated in the Rosebery-Williamsford district in western Tasmania, have a history of production dating back to 1896-7, although full scale production did not commence until 1936, following the development of a satisfactory process of selective flotation (Hall, Cottle, Rosenhain and McGhie, 1953). The mineral composition of the Rosebery zinc-lead ores was first described in detail by Stillwell (1934). The Hercules ore is generally similar, but as yet no descriptions of it have beenpublished.Since Dr. Stillwell&apos;s paper appeared, the management of the Rosebery and Hercules mines has from time to time submitted a number of interesting mineral specimens to C.S.I.R.O. Mineragraphie Investigations. Examination of these specimens brought to light eight minerals, some relatively uncommon, not previously recognized in these ores.They are cassiterite, molybdenite, stannite, electrum, meneghinite, boulangerite, pyrargyrite and pyrrhotite. Some of the specimens are also rich in tetrahedrite and gold. In addition each of the other ore minerals described by Stillwell, viz. pyrite, sphalerite, galena, bournonite, chaleopyrite and arsenopyrite, was detected in one or more of the specimens examined during the present study. The principal gangue minerals were found to be quartz, manganiferous carbonate, sericite and barite, agreeing closely with the observations of Stillwell.The present study was based on the examination of the following eight specimens.

Jan 1, 1960

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0&#183;5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By VAN. H. MANNING

Probably no year in the history of the United States showed greater progress in the mineral industries than 1916. Although this progress was undoubtedly stimulated by the war in Europe, which caused extremely high prices for some of the metals, yet the fact remains that mining is being regarded more as a business and less as a speculation, and the benefits of business methods are becoming evident. Practices that were almost universal a few years ago have been largely abolished, the mining public has been brought to recognize the folly of wasteful and dangerous methods, and there is a gratifying unanimity of opinion in regard to the conservation of life and health, as well as of our mineral resources. The people of the United States realize more fully than ever before the extent and value of the country's mineral resources and the possibilities that await intelligent and well-directed efforts at utilization. In the past, economic reasons caused deposits of valuable metals and industrial materials to lie idle; commercial reasons, many of them not truly economic, led to the waste of valuable constituents in many ores; the recovery of minerals from the ground was too often incomplete and accompanied by uncalculated loss; and the treatment of ores in mills and smelters saved altogether too Iowa proportion of the metals sought. Now better methods are being tried on every hand, and the unparalleled record of the year is largely due to the success of these efforts. According to the preliminary estimates of the United States Geological Survey the output of metals and minerals in this country in the calendar year 1916 had a total gross value of slightly more than $3,000,000,000. For many metals and minerals the figures broke all previous records, the new records of some products, as compared with 1915 figures, being as follows:

Jan 1, 1917