Search Documents

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By Ludger Suarez-Burgoa

At the Porce III Underground Powerhouse Complex in Colombia, the observational method (Peck, 1969), was used to provide information to an underground wedge and a 2D Finite Element Method numerical models, both used to estimate the mechanical behavior of the hoisting rock mass. The observation process consisted in collecting fault events in the field and in interpreting Multiple Point Borehole Extensometers and Surface Convergence Displacement Points readings. The calibrated models were employed to predict the behavior of the pillars formed between the machine and transformer caverns. The observational method is an important activity during excavation of large openings and provides arguments to understand the rock mass mechanical behavior.

Jan 1, 2008

The area (330 sq. miles) shown on the map of the Brocks Creek District (Fig. 1), was mapped by the Northern Territory geological party of the Aerial, Geological and Geophysical Survey of Northern Australia. This work was done in two stages:-(i) In 1935, an area of 30 sq. miles around the Golden Dyke mine was mapped by P. S. Hossfeld, Senior Geologist, and A. H. Voisey, Assistant Geologist. The results were described in a detailed report (10).(ii) In 1939, an area of 300 sq. miles in the Brocks Creek district was mapped by C. J. Sullivan (Senior Assistant Geologist), and V. M. Cottle and S. N. Kiek (Assistant Geologists) under the general supervision of P. S. Hossfeld (Senior Geologist).An outline structural map, together with some geological notes was published (1), but that map does not show the amphibolites, and the relationship between ore occurrence and general geology is not emphasised. The publication of the detailed maps and reportwas postponed indefinitely as a result of war. The original mapping was based on air photographs with a scale of approximately 1 in. to 1,200 ft., and all detail which could be shown at that scale was mapped. Features recorded included rock types, details of structure, mineralisation, and surface workings, creeks and soil boundaries. Underground mapping was also carried out. The present map is much simplified from the original, but it is hoped that it shows sufficient information to reveal close relationship between structure, granite, sills of amphibolite and gold occurrence. About 50 per cent. of the area is covered by deep soil or alluvium, and in these portions the geology of the underlying rocks was not determined with accuracy, though in many places strike trends could be deduced from air photographs.Because the A.G. & G.S.N.A. had published the geological notes and map referred to above, and because the publication of the detailed report and maps is still postponed indefinitely, approval has been given by the Bureau of Mineral Resources, Geology and Geophysics (which took over the affairs of the A.G. & G.S.N.A. at the termination of its operations) to the preparation of the present paper so that information would be available to the public.The views expressed in this report are those of author. The results of the investigation suggest that in areas where granites are predominantly concordant with bedding, ore deposits may be found at approximately the same stratigraphic horizon. It is thus important to correlate beds even though their relationship may have been obscured by faulting and folding.

Jan 1, 1950

By Milner A, Brockway D, Hodges S

The combustion of brown coals in Latrobe Valley power stations produces approximately 500 000 tonnes of solid wastes each year. This material, which includes precipitator ash, char and furnace ash, is hydraulically sluiced to large ashing ponds and the supernatant solution is ultimately discharged to the sea. There are significant operational and capital costs associated with the current ashing system. The ash produced from the Latrobe Valley coals is unique and has a wide variety of potential applications including soil conditioning, concrete and cement extenders, fillers in non-metallic materials, components of building products. In addition, with the application of appropriate technology, it is possible to extract char, sodium sulphate, calcium carbonate and magnesium metal (as the chloride) in substantial quantities from the ash. Research has been carried out to explore the prospects of these various options for ash utilisation. The research has focused on detailed characterisation of the ash material and the potential extraction efficiency for various species under various conditions. From this work a conceptual process has been developed and subsequent studies have been directed towards understanding variables and optimising operating regimes for product extraction. Currently, the work is concentrating on the separation of char, the development of high-grade carbon products and the extraction of sodium sulphate.

Jan 1, 1992

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind. limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By J. C. Loretto

"OPENING REMARKS Yesterday and today we have heard some very interesting papers on operating matters and some of you are probably wondering what we are now doing talking about Communications in Plant Design. Let me tell you! Before the techniques we have heard being discussed can be used, there has to be a properly operating plant. It is certainly a fact that many mineral processing plants achieve only limited success and a number of them can even be said to be failures. Some of you sitting here are probably living with operating problems that are clue to errors in the design.If the histories of these problem plants are examined, it will be found that in many cases, the necessary skills were available during the period of the plant design. There was extensive operating know¬ledge together with a full range of project expertise. Why then the failures? In a substantial number of cases it can be traced to the old, old problem of communications. As plants get bigger, money costs more and smooth startups become more important, it becomes less and less economic to fix up any design errors during plant operations.During our careers in mineral processing, nearly all of us will be involved in at least one plant design and I feel that it is as well if we understand some of these communication difficulties that can lead to a problem plant. There is little point in us being experts in mineral processing if the knowledge we have acquired doesn't somehow get incorporated into the plant.I would, therefore, like to present this short paper that mentions a few of the significant communication problems that can occur during the design of mining and mineral processing plants, together with some thoughts on answers to these problems."

Jan 1, 1973

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world's production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999

Copper mineralization associated with minor molybdenum, silver, and gold occurs in a hydrothermally altered brecda within a granodiorite mass of Upper Permian age. A dyke system of rhyolite, dacite, and andesite forms plug-like bulges near the breccia and probably caused mineralization as a late stage effect.Base metal sulphides occur as disseminations, fracture and cavity fillings in the breccia. A pyritic halo in hydrothermally altered granodiorite surrounds the breccia and grades into unaltered granodiorite. Drilling during 1969 indicated the grade is subeconomic.

Jan 1, 1972

By A. Berry, N. R. Banerjee, C. S. Finnigan, M. Fayek, N. J. Bridge

Lac Cinquante is a mineralogically simple, vein-hosted uranium deposit in Archean basement rocks (Angikuni greenstone belt) that originally were unconformably overlain by Proterozoic sedimentary and volcanic rocks of the Baker Lake Group (BLG). Basement rocks are mainly pillowed and massive tholeiitic lavas (N-MORB) with interbedded tuff; overlying sedimentary rocks comprise a basal talus/fault breccia that grades upward into fluvial sedimentary rocks and subaerial, trachytic volcanic rocks; granite and porphyry dikes (Hudson and/or Nueltin granitoids) intrude the basement rocks. A typical section through the Main Zone comprises 1) laminated ‘tuff’, 2) altered (carbonate-hematite-chlorite) schistose ‘tuff’, 3) a pitchblende-bearing, breccia-vein, 4) altered ‘tuff’, and 5) laminated ‘tuff’. The vein comprises brecciated chlorite, hematite, and pitchblende with carbonate cementing the breccia. Graphitic ‘tuff’ with sulfide-stringer veinlets locally overlies or underlies the vein. Pitchblende also occurs in the altered rocks and in gash veins that cut basement rocks. U-Pb ages on pitchblende fall into two groups: one at 1828 } 29 Ma reflects primary uranium mineralization, and a second at 1437 } 31 Ma represents resetting. Pb-Pb chemical ages show other resetting events at 1260-1321Ma, 895 Ma, 741-813 Ma, and 660-706 Ma. One possible genetic model for the Lac Cinquante deposit involves leaching of uranium from granitoids and the BLG by basinal brines that migrated to depositional sites where graphitic rocks acted as a reductant. A second model requires that uranium was sole-sourced from the BLG and that granitoid rocks provided heat to drive the hydrothermal system, which leached and ultimately precipitated uranium. The deposit has characteristics similar to vein-type uranium deposits in the Beaverlodge District of Saskatchewan

Jan 1, 2013

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By L Teixeira, C J. Greet, P Karageorgos

Pyrite is ubiquitous within copper ores, and presents significant challenges to most operations in terms of its impact on copper sulfide concentrate grade and recovery.Samples of ore containing from 3 to 47 percent pyrite, with nominally the same chalcopyrite feed grade, were collected from a copper mine in eastern Australia for testing. The ores were ground under standard conditions using forged steel grinding media in the Magotteaux Mill® to determine the impact of increasing pyrite feed grade on the pulp chemistry of the system and subsequent rougher flotation response. Attempts were made to correlate the pulp chemical parameters (oxygen demand and EDTA extractable metal ions) with flotation behaviour to determine if one (or more) could be used as a metric to infer metallurgical behaviour.The observations made were then tested under different grinding environments (obtained using more electrochemically inert high chromium) grinding media to determine if they hold true.CITATION:Greet, C J, Karageorgos, P and Teixeira, L, 2015. The influence of pyrite on the pulp chemistry and copper flotation response of a chalcopyrite ore, in Proceedings MetPlant 2015, pp 175–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015