Search Documents

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By S. N. Monteiro, J. Alexandre, L. G. Pedroti, D. P. Santos, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

The glass cutting industry is responsible for generating large quantities of waste, during the stages of cutting and polishing. The disposal of this material generates a cost to the company, thus looking for ways to repackage it, so there is the possibility of incorporating it into the adhesive mortar. The objective of this work is the characterization of waste and assessment of the properties of these mortars, fresh, and check the possibility of their use. As for the characterization, were carried out particle size testing, density and pozzolanic activity, for the fresh state were performed tests of air content, water retention consistency and entrained particular index. Were incorporated 0,10, 15 and 20% of the amount of sand. The results showed that the material on display ha spotential for use in adhesive mortar, with values within the limits stipulated by Brazilian standards.

Mar 1, 2017

By Dan A. Mackie

Continuous leaching of precious metals ores in a vat is possible using a jigging technique. This patented method promises to be competitive with heap leaching, particularly in northern climates, difficult terrain, high precipiptation regions, and environmentally sensitive areas. The paper discusses test work to date, plans for pilot plant testing and basic economics

Jan 1, 1990

By Wenjun Duan, Qingbo Yu, Qin Qin, Junxiang Liu

In the study, the coke-oven gas (COG)-steam reforming process using hot blast furnace slag (BFS) as the heat carrier is explored for producing hydrogen and recovering high-grade waste heat of hot BFS. The method of the Gibbs energy minimization approach through Lagrange multiplier is adopted in the thermodynamic analysis of reforming process. The simulation is carried out to study the operation pressure, temperature and steam to carbon ratio (S/C) based on the chemical equilibrium calculations. The optimal operation conditions are determined to improve the yield and fraction of hydrogen in the COG-steam reforming process. The results suggest that the preferential operation conditions for COG-steam reforming process to produce hydrogen are achieved at 600ºC, 1.5MPa and S/C (5.0). Due to the CaO and other melts in BFS, CH4, CO and CO2 in COG are converted and removed efficiently, especially CO2. The hydrogen fraction reaches to 86.7% and its production is about 1.22mol with 1mol of the COG.

Jan 1, 2016

By Dietrich Gross

This paper describes an advanced oxy-fuel combustion technology for re-melting aluminum that significantly reduces energy consumption and emissions. This oxy-fuel combustion technology developed by Jupiter Oxygen is a patented process for combustion of fossil fuels with pure oxygen while excluding air, thereby creating an undiluted high flame temperature and increased efficiency for process heating in industrial furnaces. This unique process has led to improved heat transfer and longer residence time while maintaining the same process temperatures as with air combustion. The energy efficient combustion process allows aluminum companies to operate at a substantially lower cost due to a dramatic fuel savings of up to 70% for natural gas and waste oil (1). The results of more than 10 years of day-to-day experience utilizing the Jupiter Oxygen Corporation oxy-fuel combustion technology licensed to Jupiter Aluminum Corporation in the aluminum re-melting business are discussed.

Jan 1, 2008

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Huimin Zheng, Jian Yang, Chun-ling Yao

"Mercury in flue gas of coal-fired plants was concerned as another serious pollution when sulfur dioxide pollution was controlled now. The adsorbent made from fly ash by thermal precipitation sulfur to remove mercury in fuel gas from coal combustion plant, SEM, BET, TGA and other measurement methods were used to characterize the effect on surface morphology, sulfur distribution and specific surface. High temperature deposition furnace was applied to increase sulfur content in fly ash based adsorbents produced in lab. The study found that sulfur attached to the adsorbent surface, mesopore and microporous structure, increasing its sulfur content of adsorbent. Sulfur was filled in interspace as small molecule S2, S5, increased their surface area and enhanced their adsorption capacity. The specific surface area increased by thermal precipitation sulfur, and specific surface area which increased with increasing temperature.1. IntroductionThe mercury emission caused by human activity has accounted for 10%-30% of total mercury emission all over the world[11, and the emission from coal-fired power plant have a huge proportion of these emission caused by human activity. Active carbon microstructure and surface morphology play an important role in its adsorption capability, which offers the potential for controlling environmental pollutant, such as sewage, fuel gas, atmosphere and et al [2,31, because it is a material with high specific surface area that long been considered as an excellent adsorbent. At present, include activated carbon, fly ash, calcium-based sorbents and other novel adsorbents. The adsorption capacity and production cost were very important in the process of mercury removal by adsorbents, so the mercury removal has focus on developing adsorbents of highly-efficient. In particular, the waste of metallurgical from coal combustion and the others have a significant advantage about the cost, and they have the highly-efficient in mercury removal after modified to enhance their adsorption capacity, such as fly ash of coal-fired. Apart from specific surface area, element content, pore structure, and surface morphology of activated carbon have great effect on its adsorption ability. Compared to adsorbents without modification, active carbon impregnated with other elements, such as chlorine, sulfur, bromine and et al. had more excellent characteristics to remove specific pollutants."

Jan 1, 2011

By V. B. Telles, J. A. S. Tenorio, J. O. Alves, D. C. R. Espinosa

"The world production of crude steel in 2009 reached 1.2 billion tons. For each ton of steel produced, 150 kg of steelmaking slag and 20 kg of steelmaking dust are generated. These are wastes with considerable production and limited applications, therefore this work studied the recovery of these wastes into useful sub-products. The slag was used as raw material in the production of rock wool (a thermo-acoustic insulator) and the dust was inserted in the iron ore sintering process. Results showed that produced materials have exceptional proprieties, therefore the recovery of these wastes can contribute to decrease extraction of non-renewable resources, reduce the costs and impact of disposals, and aggregate value to the slag and dust.1. IntroductionSteel production using Eletric Arc Furnace (EAF) has grown over 119 million tones in the last years. In 2008 30.7% of all steel produced, was obtained through EAF. In United States of America (USA) the percentage of this process in the production of steel was about 58% in 2008, while in 2000 this percentage was only 47% [1]."

Jan 1, 2011

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By Run Huang, Xuewei Lv, Lei Lei, Guibao Qiu, Chenguang Bai

"The TiO2-rich slag and pig iron can be produced from ilmenite concentrate by the electric furnace process. In this study, ilmenite concentrate was reduced in a vertical furnace equipped with a weighting data acquisition system. The effects of reducing agent (carbon) amount on the iron reduction were studied. The phase transformation, morphology and chemical compositions of reduced samples were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. It was found that the reductive degree of ilmenite concentrate increased with the increase of reducing time. The phases of reduced samples were mostly iron, rutile, Ti3O5 and Fe2TiO5. The mass loss percentage increased with increasing the carbon amount from 8% to 12%. When the carbon amount exceeded 12%, the mass loss percentage decreased with the increasing of carbon amount.IntroductionIlmenite and rutile are the main raw materials for producing titania pigment and titanium metal. With the development of the titanium industry, huge amounts of titanium resources are needed. As sources of high-grade titania mineral decrease worldwide, more attention should be paid to the processes involving low grade mineral such as ilmenite ore. In ilmenite, MgO and CaO are the gangue parts. Therefore, the ilmenite refining becomes more and more popular. In the previous studies, the methods of ilmenite refining are electric furnace smelting, direct acid leaching, selective chlorination and thermal reduction [1]. Electric furnace smelting method is widely used in the titanium industry, however, which consumes a great deal of energies and has a high CO2 emission. Its essence is to remove iron oxides and obtain a high titania slag. So the thermal reduction of ilmenite concentrate is an important step in titanium industry, which can decrease carbon reagent consumption and save energy.Over the past several decades, many studies have been carried out on the mechanism and kinetics of the reduction of different ilmenite ores, which are as follows: The carbothermal reduction of Panzhihua ilmenite initiated at about 860 oC. In the temperatures ranging from 900 oC to 1400 oC, the reaction rate was changed like a shape of “M”. That was to say that the reaction rate increased with the growth of temperature at first, then decreased, afterward increased again and at last the reaction was arrested [2]. The Mohammad A.R group [3, 4] showed that the carbothermal reduction of primary ilmenite concentrate was faster in hydrogen and initiated at a lower reduced temperature than in argon and helium. The reduction in argon and helium had about the same rate and extent. Titanium oxycarbide started at 1000°C in hydrogen. The conversion of primary ilmenite concentrate to metallic iron and titanium oxycarbide at 1200 °C was completed in 300 minutes. Monoxide as the reductant to reduce ilmenite had been studied intensively by a few research groups [5, 6]. The rate and the degree of reduction depended on the formation of a metallic shell of iron which inhibited the transfer of CO to the reaction zones; titanium had a strong effect on the mechanism and rate of reduction of iron oxides. Wang and Yuan [7] studied the reductive kinetics of the reaction between a natural ilmenite and carbon. At temperature below 1100°C, chemical reaction was the rate controlling step, at 1100 to 1250°C mixed controlling was rate controlling step, above 1250°C diffusion through the product layer controlled the reaction. Zhang [8] investigated the reduction of natural, sintered and preoxidized ilmenite concentrates in hydrogen methane mixtures. Preoxidation and sintering of ilmenite concentrates changed their phase composition and caused a sharp decrease in specific surface area of raw materials and an increase in carburization temperature. Sintering also increased the metallization temperature of iron."

Jan 1, 2011

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Brian Patrick, Norman Bell, Mark Schoenfield, Thomas Weber, Dietrich Gross

"The reduction of carbon dioxide emissions and the resultant greenhouse gas affect is hampered by the fact that all fossil fuels contain copious quantities of carbon. Process tweaking can keep the amount of carbon dioxide to a minimum but cannot significantly reduce the amount of carbon dioxide generated. The very nature of utilizing fuels requires that they be burned to release the heat required for the various processes. Reduction of metal oxides to manufacture or modify pure metals, generation of power, transportation and many other forms of fuel usage result in much of the generation of man made carbon dioxide. Oxyfuel is a unique contributor to carbon dioxide emissions. While creating higher concentrations of carbon dioxide the total volume of carbon dioxide generated is reduced. This paper will examine the unique characteristics and potential of oxyfuel that make the generation of lower volumes of carbon dioxide possible.Nearly ten years ago a commercial application of oxy-fuel was installed at Jupiter Aluminum Company in Hammond, Indiana. This process was funded and developed by Dietrich Gross CEO. This aluminum remelt facility now runs completely on oxy-fuel and has continuously for over ten years. This has reduced the melt rates to as low as 750 BTU per pound in continuous melting periods."

Jan 1, 2009

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By M. X. Huang, Y. Z. Li

The titanium diboride (TiB2)-reinforced steel composite, designed for automotive applications, exhibits a combination of high isotropic Young’s modulus and low density as compared to existing advanced high strength steels (AHSS). The steel-based composite is produced by in situ precipitation of TiB2 particles during eutectic solidification followed by hot rolling, and its microstructure displays a homogeneous distribution of both large primary TiB2 and small eutectic TiB2 particles in the ferrite matrix. Instead of interfacial debonding, particle cracking is the primary mode of damage, revealing very high interfacial strength. To investigate the intrinsic interfacial strength, a hybrid method combining both nanoindentation and finite element analysis (FEA) was used. A micron-sized sample containing a single crystal TiB2 attached to the ferrite matrix was fabricated by focused iron beam (FIB), and was compressed using nanoindentation with a flat indentation tip. By combining the compression and FEA results, the interfacial strength was therefore determined.

Mar 1, 2017

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By Thomas Niehoff, Yin Qing, Wei Zhongling, Liu Yongguo, Zhang Deliang, Tang Le

The gold ore of Shandong Gold Mining (Xinhui) was a refractory ore, which contained multi metallic sulfides (ZnS and PbS etc.) and carbonaceous. The gold ore concentrate came into leaching process and thickener and zinc replacement to recover gold. In order to improve gold recovery, the GOLDOX™ hydrometallurgy process was studied in Shandong Gold (Xinhui) by bench scale and 6 month plant scale test supported by Linde Gas. It was shown that the process promoted the leaching kinetics and improved gold recovery. The residue grade reduced 0.22 g/t in average after oxygen was applied. This indicates an operating profit increase 850,000 yuan/a in the plant. It was setting a good example for similar gold mine plant and would promote the oxygen application in Chinese gold mining industry.

Jan 1, 2015