Search Documents

By M. Adnan Göksel

Pyrite cinder is generated by roasting pyrite for sulfur dioxide production. It contains up to 62% iron, but also may contain other hazardous or toxic materials such as Zn, Pb, As, T1, Cd, Cu, Sn and S. Furthermore, the physical characteristics are not properly suited for conventional sintering. As a result pyrite cinder is considered to be unsuitable for iron and steelmaking or for outside storage because of its potential for causing environmental problems. In recent years industrialized nations have put increasing pressure on the manufacturers to either use such waste products or properly dispose of them. In this study, solutions to both the iron recovery and disposal problem were attempted by pelletizing the pyrite fines with internal carbon. The pellets, after hydrothermal hardening, were reduced and melted in a furnace for hot metal production. Hot metal of usuable quality was produced and the hazardous materials were either collected with the fumes or in the slag.

Jan 1, 1984

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By A. Bhattacherjee

Industries in general and the mining industry in particular have become more safe than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction through job design, work procedures, and worker training. Mine accident and hazard control has to be practiced in a manner which is consistent with the overall objectives of the mine management, among which are the optimum allocation and effective utilization of the resources. The purposes of this paper are to (i) review the role risk analysis in safety management with references from mining and other industries; (ii) discuss the risk measures appropriate for injury analysis; (iii) present a set of analytical tools to injury experience data in under-ground coal mines; (i v) apply these tools on case study example; (v) discuss the results of the case study; and (vi) amplify the application limitations and the future research needs.

Jan 1, 1991

By T. B. Thompson

The Leadville District has been a prominent metal producer since its discovery in 1860. Veins and replacement bodies both have contributed to district production. The latter have been the major metal sources and are hosted within the Paleozoic Leadville, Dyer, and Manitou Dolomites. Igneous bodies representing eight separate events cut the sedimentary section. The main intrusive complex within the district occurs in the Breece Hill area and was the thermal center about which the vein and replacement ores exhibit mineralogical zoning. Precious metal-pyrite-quartz veins (quartz Th= 422 to 469°C; salinity < 4.2 wt. percent eNaCI) occur within or peripheral to the Breece Hill Intrusive Complex, whereas base metal veins and replacement bodies extend from the complex margins outward as much as 2 mi. Pre-ore and post-ore igneous bodies occur, but Fragmental Porphyry dikes immediately post-date the ore event. The Fragmental Porphyry grades downward from a heterolithic breccia with rock-flour matrix to one with a dark, glassy, sulfide- and phenocryst-bearing matrix, commonly with quartz-feldspar porphyry selvages on the dike. Two types of replacement bodies are recognized in the district: 1) the Leadville-type (LTM), massive sulfide (> 60% sulfides) bodies with recoverable Zn, Pb, Ag, and Au, and 2) the Sherman-type (STM), sulfide bodies (low total sulfide) with barite, galena, sphalerite, argentian tetra.hedrite, and minor pyrite. The latter type occurs only within the Leadville Dolomite and is found throughout the Mosquito Range and extending into the Alma District. The Leadville-type replacement bodies are zoned with a pyritic margin and base metal core. Wallrock alteration and trace Pb-Zn dispersion are strongly developed in igneous wallrocks but are weakly developed in carbonate wallrocks. Cu:Zn, Ag:Zn, and Au:Fe ratios increase outward from the center to the margins of LTM. Some of the sulfide bodies are localized on earlier-formed magnetite skarns. Pyrrhotite, pyrite, and marcasite are the earliest formed sulfide phases while chalcopyrite, marmatite, and galena developed later. Tetrahedrite and electrum occur in vugs and fine veinlets cutting the sulfides. Late-stage barite, dolomite, and fluorite occur as minor phases. Pressure-corrected Th for quartz (375-410°C), sphalerite (374-387°C), barite (320-360°C), and dolomite (310-314°C) fluid inclusions with salinities < 5.2 wt. percent eNaCI characterize the fluid responsible for the formation of the Leadville-type orebodies. These values clearly demonstrate the high temperature and low salinity of the ore fluids. Sulfur isotope analyses for galena and barite from LTM are - 1.9 to + 0.9%o and 7.8%o, respectively. Proximity to feeder veins and favorable dolomite hosts are the principal controls on ore localization. The Sherman-type bodies are not internally zoned but commonly have host rock silicification near the orebody margin or in the footwall rocks adjacent to fluid flowpaths along faults. Early quartz, pyrite, dolomite, and white barite precede base metal-silver minerals which are followed by late quartz and golden barite. It is not clear whether the early quartz and the late quartz and barite are part of the STM-forming process. Fluid inclusion analyses yield trapping temperatures as follows: early quartz, 316-341 °C; barite, 264-347°C; low-iron sphalerite, 215-265°C; and late quartz, 260-278°C. All inclusion fluids have salinities < 8.1 wt. percent eNaCI. Sulfur isotope values for barite and galena from STM range from 13.2 to 24.00/00 (avg: 18.4%o) and -6.8 to -3.8%o (avg: -5.5o/00), respectively. A hydrothermal fluid d34SSS of about 15%o is needed in order for galena and barite in equilibrium to exhibit the observed sulfur isotope compositions. Equilibrium sulfur isotope fractionation between barite and galena indicates a 300°C temperature of deposition. Two separate hydrothermal events appear to have taken place to form the distinctive Leadville-type orebodies and those of the Sherman-type assemblage. The STM is known to be older than the LTM. The latter is likely mid-Tertiary in age, post-dating emplacement of the Johnson Gulch Porphyry. LTM is clearly related to meteoric leaching of sulfur and lead (and other metals) from the upper portions of the Breece Hill Stock. Fluids were transmitted along faults, bedding planes, and contacts, and cooled away from the intrusive complex. Early ore fluids were weakly acidic and developed argillic assemblages in the igneous rocks adjacent to the fluid conduits. Reaction/replacement of carbonate rocks occurred where fluids encountered dolomite, but rapid neutralization prevented any wide-spread alteration beyond the ore-carbonate host contact. Pressures based on sphalerite geobarometry and stratigraphic reconstruction were 1.0-1.2 Kb. The high temperatures of vein and replacement ore fluids indicate that chloride complexing was more effective in metal transport than bisulfide complexes. Cooling, dilution of ore fluids, and reaction with carbonate rocks were the major factors in LTM ore deposition. STM formed over wide expanses of the Leadville Dolomite terrain adjacent to (and possibly capping) the Sawatch uplift. Sedimentary sulfur was derived from Pennsylvanian evaporite-bearing sequences adjacent to the uplift. Ore leads are strongly radiogenic (J-type) and are compatible with a crustal-leaching model. Temperatures of ore formation are higher, and ore-fluid salinities are lower than Mississippi Valley-type ore fluids. Superimposed upon dark-gray, diagenetic Leadville Dolomite are several stages of hydrothermal dolomite regionally distributed astride intrusive centers of the Colorado Mineral Belt. The presence of these later dolomites argues for dolomitization and later ore deposition in response to an abnormal thermal gradient caused by emplacement of Laramide batholiths and their generation of convective flow of meteoric fluids.

Jan 1, 2013

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

The North Singhbhum Mobile Belt (NSMB) lies between two crustal-scale shear zones, the South Purulia Shear Zone (SPSZ) at the north, and the Singhbhum Shear Zone (SSZ) at the south. The Babaikundi-Birgaon Axis (BBA) is an east-west trending secondary shear zone in the NSMB lying south of SPSZ, which is known for the occurrence of gold along with other sulfide minerals within the quartz reefs. The present study has been carried out at north of Ichadih village, which lies on the BBA. The present study attempts combined electrical resistivity tomography (ERT) and self-potential methods along a profile of 470-m length in the Ichadih area to map the potential mineralized zones. Initially, ERT sections generated by Wenner, Wenner- Schlumberger, dipole-dipole, and joint inversion of the combined array have been analyzed, and results are validated through the analysis of model resolution. A prominent low resistivity (10–100 Ωm) associated with quartz reef/limonitic quartz reef at a depth of approximately 30–85 m, encircled by a high resistive (more than 10,000 Ωm) formation associated with metasedimentary rock, has been delineated using joint inversion of the combined array. Further, analysis of self-potential (SP) anomaly using particle swarm optimization inversion also confirms the prominent low SP anomaly at a depth of 77.3 m, which is analogous to the low resistivity anomaly identified in the joint inversion of the combined geo-electric array. Subsequent analysis of a complex synthetic geo-electrical model analogous to the present field situation proves the efficacy of the joint inversion of combined arrays. As a whole, joint inversion of multi-array data is established as an efficient technique for better subsurface imaging in case of the complex subsurface structure. In-depth analyses confirm the possibility of sulfide mineral-rich deposit (quartz reef/limonitic quartz reef) which requires further geological drilling and lithogeochemical sample analysis, for possible future exploration.

Oct 26, 2020

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By J. Starwood

Post-super-cycle mining executives must exploit every aspect of the value chain to deliver continued value to stakeholders. Integrating enterprise-wide information technology with value-chain-wide operational technology, known as IT-OT integration, is essential to extracting optimal results from the value chain. Mining companies trail other industries with respect to IT-OT integration across the value chain. Manual data consolidation and value chain optimization using spreadsheets and human intelligence are widespread practices within the industry. Increasing automation with smart devices and controllers means the volume and velocity of data will soon increase beyond human abilities. Enterprise Architecture provides a method for aligning information technology with the business operating model to successfully implement IT-OT integration. A Value Realization Framework (VRF) provides a means for predictable traceable value realization from IT investments and assets. With these principles, frameworks, models, methods, and techniques, mining organizations can accomplish IT-OT integration that provides their executives with a strategic value-chain-aligned platform for sustained value realization over the long term.

Feb 23, 2014

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By I. Douni

The aim of this study is to synthesize hydrated compounds of calcium silicate (tobermorite) using as siliceous source perlite milling process wastes, containing more than 70% of SiO2. Calcium silicate hydrates are mainly used for construction of lightweight building materials, plasters, tiles and filters. The effect of temperature, time and particle size of perlite on the quality and composition of the solid product was studied. The solid products were characterized by X-ray Diffractometry, Differential Thermal Analysis and the amount of Acid Insoluble Residue. The synthesis of tobermorite was per-formed by the hydrothermal treatment of perlite waste with a saturated calcium hydroxide solution at a molar ratio CaO/SiO2 of 1, liquid to solid ratio 10 mL/g and 1% w.t. NaOH addition. Three experimental sets were performed. In the first series of experiments the synthesis temperature was kept constant at 205°C while the synthesis time varied from 0.5 h to 24 h. In the second experimental series the synthesis time was kept constant at 2 h while the temperature varied between 150°C and 245°C. In the third experimental set the temperature was 205°C and the reaction time was 2 hours and two perlite waste size fractions were used, a coarse (d50=18 µm) and a fine grained one (d50=8 µm). Reaction products consisted of semicrystalline calcium silicate hydrate (I) and crystalline Al-substituted tobermorite or a mixture of both. An isomorphic Si4+ ions substitution with Al3+ ions in the hydrated calcium silicate lattice was detected by thermal analysis. The experimental results show that good quality crystalline Al-tobermorite can be produced after 6 hours of autoclaving at 205°C or after 2 hours of hydro-thermal treatment at 225°C. Generally, the in-crease of synthesis temperature or time favors the crystallization of calcium silicate phases and enriches them in aluminum. The use of fine grain size perlite is more efficient for the hydrothermal synthesis of calcium silicate hydrates.

Jan 1, 2006

By Gang Yang, Manchao He, Chengzhang Gao, Jun Zhang, Yayun Li, Jun Yang, Shilin Hou, Ben Liu, Yajun Wang, Jianning Liu

To explore the mechanism of roof directional breaking in gob-side entry formed automatically without coal pillars, the numerical simulation was used to study the deformation movement of roof, the deformation evolution of roadway, and the stress distribution of roadway under roof directional breaking and non-roof directional breaking. Based on the results, the deformation movement of roof is divided into three stages: the goaf roof collapse stage, the basic roof deformation stage, and the basic roof stability stage. The goaf is filled with gangue due to the broken expansion characteristics of the collapsed rock under the roof directional breaking. Due to the supporting force of gangue, the deformation of the basic roof under the roof directional breaking is smaller than that under the non-roof directional breaking, which reduces the influence of the deformation of the basic roof on the deformation of the roadway roof and improves the integrity of the roadway. At the same time, roof directional breaking cuts off the stress transfer path of partial roof, which weakens the peak stress convergence on the arc side, transfers the peak stress convergence to deeper, and improves the stability of roadway. Finally, a field test was carried out to further verify the accuracy of the numerical simulation. The field test results are in good agreement with the numerical simulation results. The roadway deformation is small and meets the requirements of safety production. It is proved that roof directional breaking plays a positive role in improving the stability of the roadway.

Dec 22, 2022

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By M. P. Smith, C. Hughes-Narborough, Y. T. Man

"Money and reputations can be lost in bad projects. Causes of bad mineral processing projects include poor contract definition and purchase of equipment without adequate test work. However, the root cause of many of the problems that can lead to bad projects is not any inanimate object, bad weather or catastrophic natural event but the people working on the projects. Because the people are so critical to the success of a mineral processing project, one must have suitably qualified and experienced people (SQEP) in all key positions. Characteristics that define SQEP include people who have successfully executed projects of similar size before; have undertaken projects treating the same minerals and producing the same valuable products and people who are familiar with designing, operating and implementing the required technologies and unit operations.To minimize the likelihood of future bad mineral processing projects, five recommendations are put forward in relation to the people aspect of a project.1. Attempt to retain SQEP during any down turn in the mining economic cycle so thatthe knowledge and experience can be kept within the industry.2. Increase the effort in attracting young people into the industry and retaining them.3. Set up robust training program to give young professionals a firm foundation of what real life projects and operations are like.4. Provide mentoring and continuous training for people after they have completed their formal graduate training program. Their career progression should be appropriately monitored and controlled.5. People working in projects must be exposed to as many detailed design and other finer issues as possible so that they can comprehend the amount of work required to deliver a project successfully."

Aug 1, 2016

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T &apos;1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981