Search Documents

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997

By Lee W. Abramson, William H. Hansmire

The H-3 Project is planning, design, and construction of a 10-mile (16 km)-long final segment of new highway that traverses the Koolau mountain range in Oahu. Interstate H-3 traverses North Halawa Valley on one side of the Koolau Mountains and Haiku Valley on the other side. The project includes a tunnel through the mountain range. The one-mile (1.6 km)-long twin-bore Trans-Koolau Tunnel will have two lanes in each direction. The total roadway width including shoulders in each bore will be 38 ft (11.6 m). The geologic and geohydrologic conditions along the alignment present a variety of tunneling problems. Geologic conditions consist of volcanic materials deposited generally in fairly thin basaltic layers. These volcanic materials generally weather down to "MH" soils which are compressible but relatively strong. Perched ground water that is recharged by heavy rainfall is present in the mountains. The paper presents results of initial geologic surveys and exploratory boring, and plans for exploratory tunneling and testing programs. A site specific classification method developed to characterize the weathered profile is presented.

Jan 1, 1989

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By Tim Brick, Peter Jewell, Stephen Thompson, Simon Morgan

The $980m (€750m) Dublin Port Tunnel, Europe’s biggest urban highway tunnel project, was opened in December 2006. The culmination of this immense scheme is set to transform the environment, mobility and road safety of Ireland’s capital city. This paper summarizes the key aspects of a project linking both sequential and parallel construction of individual tunnels and describes various approaches to bored, mined and pre-support cut-and-cover tunneling in a wide variety of ground types and depth of cover. Examples of innovative approaches to deal with structural and geotechnical problems while maintaining full operation of both road and rail traffic and the integrity of properties in a dense urban corridor are described.

Jan 1, 2007

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program's predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By R. W. Carn, D. Vincent

Environmental Considerations With significant increases in bulk coal movements through terminals, operators are under constant social and political pressure to reduce or remove environmental pollution problems incidental to their operations. To meet these requirements, both equipment manufacturers and terminal designers are endeavoring to design equipment and systems with stringent environmental controls. The most challenging environmental problems facing coal terminal designers and developers are terminal siting restrictions, dust control, and noise abatement. Terminal Siting Finding a suitable site can be a difficult problem because of public concern over coal dust or the impact of a terminal on the surrounding community or natural habitat of the area. Often the only suitable flat land available for terminal development is on a tidal estuary or salt water marsh with great environmental value. In many cases a period of four to six years of full environmental and social assessment has been needed. A recent example of such difficulties is the expansion at Roberts Bank, British Columbia, where environmental impact assessment studies and their public review took almost six years from initial expansion applications until the time of approval. Dust Control Modern coal terminal dust control techniques usually consist of water sprays at strategic locations to suppress dust. The application points include rail car or barge dumper, main conveyor transfers, perimeter sprays around stockpiles, stacker/reclaimer, ship-loader transfers, and loading spout. The water sprays may include a chemical wetting agent or surfactant to reduce the water requirement and increase effectiveness. Recently there have been advances with development of effective micro foam agglomerating agents. In these systems, a micro foam with very small bubble sizes is sprayed into the coal stream. The foam fills the interstices between coal particles and wets the coal fines. These systems have proven to be very effective and usually one application before stockpiling and one upon reclaiming will markedly reduce the coal dusting. Stockpile perimeter sprays can be operated either manually or at the sophisticated terminal, actuated by a computerized control system that senses key environmental conditions such as humidity, precipitation, and wind velocity. Most modern terminals collect the drainage from the stockpile area, remove the solids in settling basins, then recirculate the water to reduce water requirements and effluents from the site. Dusting of long-term storage stockpiles can be reduced by spraying the piles with chemical resin or latex binding compounds to seal the surface. These compounds also can minimize erosion of the pile by rainfall. Dust collection with air evacuation systems and cyclone or wet scrubbers can be used at key areas such as rail car dumpers, main conveyor transfers, and ship-loader spouts. The trend in dust control is away from dust collection since most dust collectors are high maintenance items requiring good operator supervision and servicing. Coal handling conveyors are usually open and uncovered. However, in areas requiring special attention they may be covered or even completely enclosed. Dust generation from terminal roads is often a significant amount of the total dust emitted from a terminal. To reduce this dusting, roadways where traffic is heavy can be paved or sprayed by water trucks. Speed limits can be enforced and use of tracked mobile equipment for stockpile handling rather than rubber-tired loaders is encouraged by authorities. Noise Abatement Terminals located close to residential areas are often faced with noise control problems. Noise can be one of the most difficult environmental problems to solve. Usually, use of electrically-powered equipment is encouraged to reduce noise levels. Rail car dumper houses can be totally enclosed to reduce both dust and noise emissions. Diesel locomotives can be fitted with special muffling devices. Green belts of trees surrounding a terminal or the ap-

Jan 7, 1983

By Elisa Comis, Jeffrey Peterson, Yama Ebrahimi

Construction of the Northeast Boundary Tunnel (NEBT), the last leg of the Anacostia River Tunnel System on DC Water’s Clean Rivers Project, started in September 2018 and was completed in April 2021. The 26-foot-bore earth pressure balance (EPB) tunnel boring machine (TBM) mined 26,737 feet at elevations between 80 to 160 feet belowground. Approximately 55% of the tunnel was cut through lower predominantly coarse-grained facies identified as the Cretaceous Patuxent Formation (undifferentiated) (PTX), and the remainder was cut through upper predominantly overconsolidated fine-grained plastic material facies identified as the Cretaceous Patapsco/Arundel Formation (P/A). Mixed face conditions were encountered in the transition from the P/A to the PTX and vice versa. This paper reviews the performance of the TBM that mined the NEBT through several unique challenges, including 8,000 feet of tunneling under the heavily developed Rhode Island Avenue corridor, major sensitive structures, cast iron water distribution mains, and other sensitive utilities.

Dec 1, 2022

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By G. Récoché, A. Chamaret, M. O’Connor

Building indicators that respond to all stakeholders&apos; needs is a time-consuming and complex exercise, with certain questions still unsolved. The aim of the current three-year research project, carried out in partnership between BRGM’s Mineral Resources Division and C3ED, is to propose a top-down / bottom-up indicators building methodology that combines conception and coordination methods and a participative approach. The tool-design phase is based partly on a comparative analysis of existing international initiatives according to different criteria (objective, observation scale, framework, etc.). The study of two African mining projects will provide the opportunity to confront the conceptual aspects with reality in the field. Careful consideration of the participants’ suggestions will result in a set of indicators that can be easily understood and adopted by all stakeholders. The final objective is to measure the impact of a mining site on a local, regional and national sustainable development frame, throughout the full life cycle of a mine.

Jan 1, 2005

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The depletion of good-quality phosphate resources, coupled by a need to supply acceptable products at a rapid rate, while meeting the specifications of fertilizer chemical plants, is of significant concern to the phosphate industry, particularly the production of concentrates with tolerable dolomite content. Tremendous efforts have been made in the past to develop an efficient and economical process that can effectively reject dolomite. However, dolomite removal continues to plague the phosphate industry due to several process-specific challenges being encountered with various beneficiation technologies. In this regard, detailed characterization of phosphate reserves is crucial to understand textural limitations and help design appropriate strategies to achieve quality products. In this paper, the development of procedures to establish dolomite rejection/francolite recovery curves for gravity preconcentration of pebble phosphate from Central Florida is described using high-speed X-ray computed tomography (HSXCT). The developed procedure is illustrated with the analysis of high MgO pebble phosphate samples (10.39 mm × 1 mm) received from South Pasture and Four Corners locations operated by the Mosaic company. The rejection/recovery curves were calculated for each sample for five different particle size classes to observe the trend in rejection/recovery with variation in particle size. In order to evaluate the reliability of the HSXCT data, analysis using the high-resolution X-ray computed tomography (HRXCT) technique was performed on one particular sample (FC-3-1). Finally, to assess the separation efficiency, the HSXCT and HRXCT rejection/recovery curves obtained were compared to experimental gravity preconcentration results reported in the literature. In this way, liberation limitations for gravity preconcentration in the processing of pebble phosphate have been established based on X-ray computed tomography analysis.