Search Documents

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

P.W.D. ROSTER OF CONSULTING ENGINEERS (Extract from a letter from the Secretary for Public Works) In recent years a large number of professional engineers has entered the consulting field. Although the names of most of these have been placed on the Department's roster of consulting engineers either as a result of representations made by the South African Association of Consulting Engineers or by applying direct to the Department there are still some who seem to think that canvassing through an influential person is necessary to obtain commissions from the Department. The Department's roster is open to all registered professional engineers who are suitably experienced to undertake consulting work and commissions are awarded strictly on merit. I shall appreciate it, therefore, if registered professional engineers who wish to be considered for commissions by the Department could be advised that they must apply, in the first instance, to be placed on the Department's roster. On receipt of such an application a questionnaire listing all the information required by the Department will be forwarded to the applicants for completion and returning to the Department for record purposes. All names which appear on the roster are taken into account when a commission has to be awarded, due consideration being given to factors such as geographical position, seniority, capability and compatibility. AMERICAN SOCIETY OF MINING ENGINEERS 1970 FALL MEETING AND EXHIBIT The Secretary for Commerce has passed to us a letter received from the American Society of Mining Engineers, reading as follows: "We would be delighted to have South Africa attend our meeting next year and to exhibit some of their mining equipment in our Technological Information Exchange. The 1970 SME Fall Meeting and Exhibit will be held in St. Louis, Mo., October 21-23, 1970, at the Kiel Auditorium. The AIME WorId Conference on Lead & Zinc Mining and Metallurgy will be an integral part of our meeting-and an added incentive to attend. It should be understood that we discourage the showing of actual mining equipment and encourage the manufacturers and suppliers to send their engineers to man the booths. We hope that the exhibits will endeavour to put across their story by means of photographs, drawings, models and literature, rather than by display of prototypes of the actual equipment. We will be happy to welcome manufacturerers from South Africa as well as the mining engineers who, from time to time, have registered at our meetings." For further particulars, interested parties may write to the Society of Mining Engineers, 345 East 47th Street, New York, N.Y. 10077, D.S.A.

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By R. C. J. Goode

"In my Presidential address last year `The Institute in Retrospect and Prospect', I briefly reviewed the past activities of our Institute, I commented on the dynamic growth of the mineral activity of this country and of the great contribution towards this growth made by members of this Institute. I maintained that there was still further growth to come, pointing out that our future would be very much dependent on the availability and skills of our mining and metallurgical men. This Institute had, therefore, a most important task ahead to ensure that this country would have the necessary skilled engineers to develop our mineral industry so that we would be able to compete successfully in the wide world. In my address I highlighted many of the major achievements of our members and of our Institute. In today's review, I have no wish to repeat myself and I would, therefore, ask members and visitors to regard this review as complementary to my presidential address. I must also refer you to the very full resume of our affairs written for a special brochure in March, 1944, by E. H. Johnson, a founder member, on the occasion of our 50th Anniversary. There is no need to repeat what was given there, rather I will attempt to bring that history up to date. Our Institute was founded under the name of Chemical and Metallurgical Society of South Africa on 24th March, 1894, by a group of chemists and metallurgists The name was changed to Chemical, Metallurgical and Mining Society of South Africa early in 1903, and in July, 1956 became The South African Institute of Mining and Metallurgy. We were not the first technical organisation in South Africa, the S.A. Association of Engineers and Architects having been formed in 1892. In that year also the British Institution of Mining and Metallurgy started in London. A chronological table of some of the more important societies is as follows: British Societies: Society of Apothecaries 1617 Royal Society 1660 Geological Society 1807 Institution of Civil Engineers 1818 Institution of Mechanical Engineers 1847 Institution of Chemistry 1877 Institution of Mining Engineers 1889 Institution of Mining and Metallurgy 1892 Other Societies: Mining Society of Nova Scotia 1887 S.A. Association of Engineers and Architects-later the S.A. Association of Engineers which amalgamated with the Transvaal Institute of Mechanical Engineers 1892 Australasian Institute of Mining and Metallurgy 1893 Geological Society of South Africa 1895 South African Society of Electrical Engineers-disbanded 1904 1897 Mechanical Engineers' Association of the Witwatersrand-later, the

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters' and boilermakers' workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By Z. Weisheng

The lift system is the main part in manganese nodule mining on the ocean bed. It connects the nodule collection system (miner) with the surface platform (mining vessel) and transports the nodules from the ocean bed to the surface. China started the research on lift technology in deep ocean mining in 1991, and a slurry pump hydraulic lift method has been developed for the nodule mining system. The detailed slurry pump hydraulic lift experiments have been undertaken with crushed nodules in the vertical pipe. The lift parameters to lift coarse particles in the lift pipeline have been discussed, including the pressure drop, the solid concentration, and the mixture velocity. The author of this paper not only took part in all these studies on the lifting technology, but was also responsible for some of this research. This paper will present the component parts of the lift system and the research results of coarse particle mixture flow in the vertical lift pipeline. Keywords: deep sea mining, slurry pump lift, lifting parameters.

Jan 1, 2007

By N. C. Gay

During the past two to three years, there have been some significant Improvements to the quality of the support systems being used on South African gold mines, and the Implementation of these new developments, together with more worker awareness has been instrumental in reducing rock-related accidents, particularly in deep mines. This paper provides guidelines to mine and group personnel on how to monitor the ongoing Implementation of new technologies and so ensure the benefits that will accrue in terms of mine safety and profitability. Particular attention is given to the establishment of auditing procedures that will enable management to assess the benefits obtained from new technologies, as well as providing Improved maintenance procedures and procedures for the optimum utilization of seismic data. The areas that receive most attention include support systems for stopes and tunnels, such as hydraulic props, backfill, and rockburst-resistant tunnel support; stope and regional support layouts; mine standards; and staffing of the rock-engineering department. The paper includes a draft audit form and a hypothetical example of an audit report

Jan 1, 1997

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By R. Van Rijswick

Crankshaft driven piston and piston diaphragm pumps inherently generate a varying flow each crankshaft revolution. Depending on the system connected, this flow variation results in a pressure pulsation. This pressure pulsation may, depending on the structural design, result in structural vibrations. In order to limit the level of pressure pulsations, volume absorbing devices, mostly gas filled vessels, are used. The standard selection of these so-called dampeners is based on the flow variation of the pump but does not incorporate the interaction with the connected system. The paper discusses the application of a pulsation analysis tool developed by WEIR Minerals Netherlands, manufacturer of GEHO positive displacement slurry pumps. The paper first discusses the basics of pressure pulsation analysis, such as flow variation generated by crankshaft driven pumps, and hydraulic effects such as capacitance, inductance and resistance and their influence on the hydraulic response of a system. Furthermore, the relation between pressure pulsations and structural vibrations, known as fluid structure interaction, will be discussed. Additionally, the capabilities of the pump pulsation analysis tool are presented, illustrated by examples of simulation results and experimental verification.

Jan 1, 2007

By S. M. Spottiswoode, Linzer. L. M.

We report on further progress in improving seismic locations by using the so-called double-difference method (Spottiswoode and Milev, 1998 and Waldhauser et al., 1999). Double-differences are obtained either using picked arrival times or various measures of time differences obtained from waveform pairs. The double-difference method provides for much improved relative locations by reducing the effect of the errors in the wave velocity of ray paths between each event and each geophone. Further improvements are obtained by using known locations, such as blasts. One of the difficult problems that we have overcome is that of finding the best “weights” for the time corrections. Experience obtained in relative moment tensor inversions by Andersen (2001) suggests that use of median corrections is both more stable and more accurate, even while the locations of the individual events is based on weighted least-squares minimization. A hybrid location program with known reference events has been developed. Tests on a synthetic data set gave relative locations that were much less widely spread than the absolute locations. The use of known event coordinates (blasts) moved the relative locations back towards the real locations. These results are confirmed in preliminary analysis of data from a mine. The absolute locations are adjusted using blast events restricted to the line of tunnel development. Inter-event distances are distributed in a power-law fashion that suggests that the relative location accuracies are improved by a factor of three or more. Nous rendons compte des progrès faits dans l’amélioration des locations de séismes en utilisant la méthode appelée de double- différence (Spottiswoode and Milev, 1998 et Waldhauser et al., 1999). On obtient les double-différences soit en utilisant des temps d’arrivée choisis soit des mesures variées de différences de temps obtenues de doublets de forme d’onde. La méthode de double-différence fournit des locations relatives très améliorées en réduisant l’effet des erreurs dans la vitesse d’onde des trajectoires de rayon entre chaque évènement et chaque géophone. D’autres améliorations sont obtenues en utilisant des locations connues, telles que les coups de mine. Un des problèmes difficiles que nous avons surmontés est celui de trouver les meilleurs coefficients de pondération pour les corrections de temps. L’expérience obtenue dans des inversions de phases tensorielles relatives par Andersen (2001) suggère que l’utilisation de corrections médianes est à la fois plus stable et plus exacte, même lorsque la location des évènements individuels est basée sur minimisation pondérée de moindres carrés. Nous avons développé un programme hybride de location avec des évènements connus pour référence. Des tests sur des données artificielles ont donné des locations relatives qui étaient beaucoup moins étendues que les locations absolues. L’utilisation de coordonnées d’évènements connus (coups de mine) a ramené les locations relatives vers les locations réelles. L’analyse préliminaire des données d’une mine a confirmé ces résultats. Les locations absolues sont ajustées en utilisant des évènements de coup de mine restreints à la ligne du développement du tunnel. Les distances entre chaque évènement sont distribuées comme par loi exponentielle ce qui suggère que les degrés d’exactitude des locations relatives sont améliorés par un facteur de trois ou plus. Wir berichten über einen weiteren Fortschritt, die seismische Positionen unter Verwendung der zu sogenannten Doppel-Unterschied-Methode (Spottiswoode und Milev, 1998 und Waldhauser et al.,1999) zu verbessern. Doppel-Unterschiede werden entweder mit ausgewählten Ankunftszeiten oder verschiedenen Messungen von Zeitunterschieden erreicht, die von den Wellenformpaaren erhalten werden. Die Doppel-Unterschied-Methode liefert viel verbesserte relative Positionen unter Verringerung der Auswirkung von Fehlern in der Wellengeschwindigkeit von Strahlengängen zwischen jedem Fall und jedem Geophon. Weitere Verbesserungen werden erreicht, indem man bekannte Positionen, wie Sprengungen verwendet. Eines der schwierigen Probleme, die wir überwunden haben, ist jenes des Findens der besten "Gewichte" für die Zeitkorrekturen. Die Erfahrung, die in den relativen Momentspannerumkehrungen von Andersen (2001) gewonnen werden bietet den Schluß an, daß der Gebrauch von mittleren Korrekturen beständiger und genauer ist, sogar wenn die Positionen der einzelnen Fälle auf der bewerteten Reduzierung der Methode der kleinsten Quadrate basiert. Ein hybrides Positionsprogramm mit bekannten Bezugsfällen ist entwickelt worden. Tests auf einem synthetischen Dataset gaben relative Positionen, die viel weniger weit gestreut waren als die absoluten Positionen. Der Gebrauch von bekannten Fallkoordinaten (Sprengungen) schob die

Jan 1, 2003

By Franz E. Pawlek

Synopsis This is a summary of investigations in the field of pressure leaching carried out at the Institute for Extractive Metallurgy of the Technical University of Berlin-West during the last seven years. The efficient dispersion of gas in a liquid and its dissolutions as well as the events at the phase boundary when leaching ZnS are reported. At the end two examples are given for the use of pressure leaching in the processing of smelter by-products. INTRODUCTION About 20 years ago, experiments were independently started in Canada and in Berlin on the subject of dissolving sulfidic ores without preliminary treatment by means of leaching under increased oxygen pressure. In Canada ammoniacal solutions were mainly employed, and F. A. Forward and his co-workers were successful in applying this process on a large industrial scale1, 2. This process is used in Fort Saskatchewan to produce about 15,000 tons of Ni per year. In Berlin, investigations were started on leaching with acid solutions3, 4. This process had also been used on a large industrial scale in the D.S.A., but the choice of unfavourable working conditions led to great difficulties, and to giving up this process for industrial use. Later on in Berlin work was carried out especially on the kinetics of pressure leaching 5, 6, 7, 8, 9 and its applications to the processing of smelter by-products, in particular of mattes and speisses10, 11, 12, 13, 14. The dissolution of ores and by-products can be subdivided into four steps: 1. the efficient dispersion of the gas, so that its dissolution occurs over as great a surface area as possible, since only the dissolved oxygen reacts with the solid, 2. the suspension of the solid, so that the entire surface can take part in the reaction, 3. the phase boundary reaction, 4. the removal of the reaction products. The first two steps belong to the field of process engineering and will be discussed from this point of view. The aim of these experiments15 was to find out first of all the limits of efficiency of self-sucking stirrers in solutions of low viscosity with regard to the mass transfer. In addition, the effect of ultrasonics in the same reaction system was studied. The experiments were carried out in a lucite container as shown in Fig. 1. Four baffles of 0.1 d width were in the stirring vessel. The height of these baffles was adjustable. For every experiment one litre of liquid was used. An infinitely variable direct current motor, which was fixed with a hollow shaft, served as the driving power for the stirrer.

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By Pieter de Waal

The beneficiation equipment under the control of plant metallurgists exploits the differences in the physical properties between valuable and waste mineral components. In many cases, laboratory results are too late for process control and can only serve the purpose of "post" reports, the calculation of a mass balance and the issue of a quality certificate. As a result, experienced operators regularly adjust separation equipment based on the colour and texture of the various product streams in the beneficiation plant. Metallurgists quickly learn to recognise the different minerals in their ore body. The stereo microscope has been a valuable tool used by operators to quantify known mineral species. For many years it was the only practical method available for the purpose of process control and even for quality contro1. The modem spectroscope is far superior to the human eye and can rapidly detect a change in mineral composition. New generation optical scanners and digital signal processors can provide useful signals, related to mineral composition that can readily be applied for the purpose of process control. Successful case studies, covering dry in-line and slurry applications as well as in-plant fast spot analysers are presented.

Jan 1, 2014

By P. N. Harris

On 23rd November, 1982, a party of 80 members of The South African Institute of Mining and Metallurgy left the Wanderers Club grounds at 07hOO, and were driven in two luxury coaches to the stainless-steel mill of Southern Cross at Middelburg. Southern Cross is a trade name adopted by MS & A (Middelburg Steel and Alloys), who operate two Alloy Divisions (at Middelburg and Krugersdorp) and one Steel Division (at Middelburg). METAL '83 The International Precious Metals Institute has scheduled a seminar on the platinum -group metals for Williamsburg, DB.A., on 10th to 13th April, 1983, and has announced its keynote speakers for each of the seminar's five sessions. Metee '83 METEC - the International Exhibition for Metallurgical Technology and Equipment with Congress - which was to have been held in Dusseldorf from 14th to 20th May, 1983, has been cancelled, and will probably take place in June 1984. Sampling Sampling and sample preparation are crucial activities in many areas of chemical engineering, in the energy and food industries, in metallurgical processes, and in mining and mineral engineering.

Jan 1, 1983

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007