Search Documents

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

1. The following recommendations should apply to all mines, tunnels and underground quarries, but to opencast quarries only in so far as persons can be exposed to dust injurious to health. General In the present state of knowledge, all duets liberated in mining, tunneling and quarrying operations should be considered potentially injurious to health if breathed in sufficient quantity; dusts containing free silica should be considered specially injurious to health, the injurious particles being below 7 microns in diameter.

Jan 1, 1954

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966

By L. R. Burdick

Anthracite barley is considerably cheaper than rice. Its use, therefore, is attractive from a cost standpoint, - but its smaller size (through 3/16 inch over 3/32 inch round-mesh screen) makes it more difficult to use on some equipment when fairly high combustion rates are necessary to carry plant loads. Tests wore made in one plant to determine the performance of rice and various types of barley on a chain-grate stoker in a two-arch refractory furnace. In general, the efficiency and capacity increased with increased fuel size and volatile content. This performance is presented in tabular and curve form, together with a short review of the ignition and burning process on chain-grate stokers and a discussion of the operating procedures and limitations during the tests. In this particular installation, higher combustion rates and efficiencies could have been obtained with barley if the grate links had been designed for more uniform air flow through the grate surface. Careful maintenance and operation are particularly necessary for satisfactory results with barley on equipment not especially designed for its use.

Jan 1, 1950

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By Worthen Bradley

This paper describing the metallurgical practice and costs at the reduction plant of the. Sulphur Bank Syndicate, Clearlake, Calif., is one of a series of papers on the treatment of ores being prepared by the Bureau f Mines. The reduction plant and mine of the Sulphur Bank Syndicate are on the eastern shore of Clear Lake, in Lake County, Calif., 4 miles from the town of Clearlake and 125 miles north of San Francisco.

Jan 1, 1931

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1968-69. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By James R. Boyle

The value of mineral production increased 6.2% in 1976. With the exception of coal, practically all commodities registered an increase in production and value; most had an increase in unit value. Total value exceeded $1 billion for the first time. The increase in nearly all nonmetallic mineral production was a complete reversal of the 1975 experience. Alabama led the Nation in the production of crushed marble and was second in bauxite and scrap mica, third in oystershell, third in kaolin, and fifth in dimension limes-tone and dimension marble. International Trade.-The international trade passing through the Mobile customs district was valued at $2,524 minion in fiscal year 1976, up 20% from that of the previous year. Of the total value of trade passing through the district, 52% of the value of experts and 89% of the value of imports were handled through the port at Mobile. The major export Commodity was coal through McDuffie Coal Terminal which amounted to nearly 2.9 million tons, up from 2.4 million tons in 1975. Coal exports were to Japan, Italy, Turkey, the United Kingdom, and Brazil. Other exports were cement (114,000 tons) and [ ]

Jan 1, 1979

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By Steven J. Schatzel

Large-scale methane releases in dual salt mines have resulted in ignitions and mine fatalities as recently as 1979. Several past studies have implied that hazardous methane occurrences in U.S. salt domes are distributed neither uniformly nor randomly, but are geologically controlled and potentially predictable. A first step by the Bureau of Mines in addressing the problem of methane in deal salt mines required development of a new test to determine volumes of gases in solid salt samples. This report considers the results achieved when 80 deal salt samples were tested for gas content by dissolution in a controlled atmosphere chamber. Criteria were organized to delineate salt types based on geological occurrence. Outburst samples range from 0.014 to 7.4 cm3 CH4/100 g NaCl, anomalous salt samples from 0.0027 to 2.6 cm3 CH4/100 g NaCl, and normal salts from less than 0.0003 to 0.31 cm3 CH4/100 g NaCl. The presence of higher hydrocarbons was most common in samples containing larger quan¬tities of methane. The presence of higher hydrocarbons appears to be useful in detecting methane hazards where some methane may be lost before gas content testing. An exploratory rotary and/or core drilling program, dissolution testing for gas content, and up-to-date geologic mine napping could allow a mine operator to assess methane hazards in dual salt.

Jan 1, 1984

By Liane L. M. Kacinuck

This U.S. Bureau of Mines publication is intended to provide mining industry representatives and regulatory authorities with a reference package dealing with studies on hydrology and underground mine subsidence. An annotated bibliography and a list of additional sources are given and represent references published prior to June 1993. Ninety-two references ware identified and 72 obtained for assessment. Annotating the references included evaluating the study methodology and summarizing the basic results. The references are also compiled based on geographic location to aid the user in identifying articles of particular interest.

Jan 1, 1994

By K. K. Kelley

Despite the wide interest in titanium and its compounds, no heat and free-energy-of-formation values for titanates (that is, compounds formed from titania and other metal oxides) have been available heretofore except for ilmenite (FeTi03). Such data are needed for understanding and developing processes for producing titania and titanium tetrachloride from ores (and possibly slags) and in connection with ceramic usage of titania. This paper reports experimental measurements of the heats of formation at ordinary temperature of 11 titanates-ilmenite, perovskite, barium metatinate, strontium metatitanate, barium-strontium metatitanate, barium orthotitanate, strontium orthotitanate, barium-strontium othotitanate, geikielite, magnesium-titanium spinel, and magnesium dititanate. The experimental method was solution calorimetry. The solution calorimeter was operated at 73.7°C. and used a strong hydrofluoric-hydrochloric acid mixture as the calorimetric fluid and reaction medium.

Jan 1, 1954

By F. E. Walker, S. J. Aresco, J. B. Janus

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal , expressed in British thermal units , and the composition as shown by proximate analyses . To these , when required , are added the ash- softening temperature , the free - swelling index , and the Hardgrove grindability index . Under most of these specification contracts the bidders guarantee the quality of the coal , and that guaranteed by the successful bidder becomes the standard of his contract . The deliveries are sampled in accordance with instructions 4/ issued by the Bureau of Mines ; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and , if it is not , a price adjustment is made . Analyses of the delivered coal and tipple samples ( samples collected at mine tipples as coal is being loaded into railroad cars or trucks ) provide valuable data for use in evaluating future bids . In addition , the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal . The Government purchased approximately 5 million tons of coal in fiscal year 1962. In connection with these purchases , the Bureau analyzed 7,114 samples . These are published ( table 1 ) for the use of Government officials and the public . A series of publications has been completed on coal analyses by States or , where production is small in any one State , by groups of adjacent States . In addition to analytical data showing composition and quality of coals of the States , the publications contain brief descriptions

Jan 1, 1963

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By John Nagy

The Bureau of Mines adapted thermal theories explaining combustion of gases to correlate parameters affecting ignition of dust dispersions. The dust dispersions were ignited in a Godbert-Greenwald furnace at atmospheric pressure. Ignition temperature and the concentrations of fuel, admixed inert powder, and atmospheric oxygen were related mathematically. Values for these parameters obtained in laboratory experiments for cornstarch agreed with theory. The developed equation permits extrapolation; the predicted upper igni-tion limits correspond with limited experimental data from laboratory and large-scale tests. Explanation of the effect of fineness of dust on ignition parameters is attempted by introducing a surface-area constant to modify the activation energy. Arguments are presented to show that the ignition process is a solid-gas phase reaction rather than an ignition of prevolatilized gases.

Jan 1, 1966