Search Documents

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By W. F. Hazen

This paper describing the mining practices at a 100 per cent mechanized mine working the Pittsburgh or No. 8 coal bed in eastern Ohio is one of a series being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The purpose of assembling this data is to place before those interested in the mining industry the methods employed and the cost data on the items involved in the winning of the coal and its removal to the railroad car at the tipple. Mining costs are governed by the mining method used, which is selected for its adaptability to local natural physical conditions such as the nature and thickness of the coal, its dip, the character of the roof and floor, and the thickness of the overlying strata.

Jan 1, 1929

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emission in 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States hid daily methane emissions of 1 MMcfd or more. These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va., which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.3 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1977

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By Wilbert J. Huff

[This is the fifth of a series of annual reports of the explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with work done during the period July 1, 1939, to June 30, 1939. The writer and the respective unit leader to whom credit is indicated have directed the various studies outlined.]

Jan 1, 1940

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By Radford B. Langston, John A. Marjerison, Graham C. Howell, Hendrik A. D. Kirsten

Probabilistic design is gaining wider acceptance in the rock engineering community since it allows more rigorous determination of risk relating to ground fall or excavation instability. Risk analysis can be conducted by various means, but the basis is formed by either objectively or subjectively determining probability of occurrence of an event. In the case of rock engineering, this event is either instability or excavation failure. Rock mass classification systems provide objective analysis of data collected on a typically subjective basis that also relate closely to excavation stability. A probabilistic analysis technique is presented that uses statistical distributions of rock mass and material properties, ground support fixture specifications, stress conditions, opening geometry, and ground support installation quality to more rigorously determine probability of failure for an underground opening and the subsequent risk to personnel.

Jan 5, 2007

By M. A. Trevits

During the time period from 1990-2007, 1601 reportable fires occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires were flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The fact that mine fires continue to occur with an alarming regularity reinforces the importance of recognizing and eliminating the potential hazards and the overall need for improved fire control and suppression technology to ensure the best possible outcome during a mine fire. The National Institute for Occupational Safety and Health (NIOSH) is conducting an evolving comprehensive program of research that is addressing mine fire prevention, detection, management and suppression. This paper presents a summary of recent research accomplishments and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2008

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By C. E. Arrington, A. C. Rice

"Part 1. REDUCTION AND USE OF OXIDANTSSUMMARYA study has been made of the volumetric determination of molybdenum by reduction in the Jones reductor, receiving the reduced solution in a mixture of ferric alum and phosphoric acid, and titrating with standard oxidizing agents. In addition to potassium permanganate, which has long been utilized for this titration, potassium dichromate and ceric sulphate have been found to be applicable. The latter oxidants have been found to be especially useful in the form of dilute solutions for the determination of small amounts of molybdenum. The tests revealed that certain internal indicators give excellent results in these titrations.Reason for These ExperimentsThe following study was initiated with the hope of providing the mining and metallurgical industries with an accurate and rapid technical method for the determination of molybdenum in such low-grade materials as ores, rocks, tailings, steels, and alloys containing less than 0.3 percent molybdenum. Although the experimental work was designed with this purpose in mind, many of the results are applicable to material containing a higher percentage of molybdenum.While the Bureau of Mines had an experiment station in Colorado, considerable analytical work was done on what were then (up to about 1923) classed as rare metals. One of these was molybdenum; and in Bulletin 212, Bonardi's (1) 3/ 60-page chapter covered all methods for the analysis of molybdenum."

Apr 1, 1939

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By D. Harrington

"Coal—mine explosions are accidents that can and should be prevented. In former years hundreds of lives were lost each year in the United States as a result of such explosions, but after 1932 the numerous precautionary measures adopted had reduced their frequency and severity 75 percent or more until in 1940 several very disastrous explosions marred the good record. Unfortunately, both the number and severity of explosions seem to be tending to increase compared with the relatively good achievement from 1933 to 1940. The requisites for an explosion are ever present in all soft-coal and many hard-coal mines. A certain combination of circumstances, such as a flame or an arc in a cloud of dust or in a body of gas or both may start an explosion at any time. The fact that the frequency and severity of explosions were lowered for 6 or 7 years is no guarantee that such freedom from explosions will continue, as the bad record of 1940 has shown, and underground workers should feel honor bound to exercise the utmost care so that they will not help to bring about the circumstances that will cause an explosion.Although mine operators bear the main responsibility for preventing explosions, miners can do many things to help. As about 9 out of 10 explosions begin at a working face, it is largely within the power of workers to prevent them. All miners should do their part willingly and should not defend a fellow workman from punishment, even from discharge, for disobeying necessary rules, whose disregard may cause the death not only of the safety-rule breaker but also of many of his coworkers.When a miner is careless and is injured some other way than by an explosion he may be the only one to suffer, but if his carelessness causes an explosion he not only endangers his own life but also that of every other man in the mine and possibly the lives of persons outside the mine.Experiments have shown that ignition of as small a quantity as 150 cubic feet of an explosive mixture of methane and air under certain circumstances can start an explosion that will traverse an entire mine. Thus, ignition of an explosive mixture of gas 1 foot down from the roof and 13 feet back from the face of a 12-foot entry might cause a widespread explosion if the right quantity and kind of dust were present. Many persons have ignited much larger quantities of gas without being killed, but they survived only because dust, confinement, and other conditions were not exactly ""right."""

Nov 1, 1940

By D. Harrington

Before the present century there existed a fairly persistent demand for the establishment of a Federal Department of Mines, but relatively little was done about it until a considerable number of very serious coal-mine disasters in 1906, 1907, 1908, and 1909 created what might almost be termed a national scandal and virtually forces the Federal. Government to take action to try to solve the problem of the cruse and prevention of such disastrous occurrences. Instead of a Department of Mines, the mining people had to accept a bureau, which was created on July l, 1910; and while the Bureau of Mines was given numerous functions, unquestionably the promotion of safety in the mineral industries was and continues to be one of its main "jobs." The Bureau's organic act was approved in 1910 and amended in 1913. Both the original and amended acts indicated that promoting; the health and safety of the mine workers constituted the chief function of the Bureau, and that this was the construction placed on its activities by those put in charge in 1910 is shown very definitely by the fact that as soon as the Bureau came into existence on July 1, 1910, both health end safety activities were started in its Mine Accidents Division. Before the end of the first fiscal year (June 30, 1911) 6 mine safety stations had been established in various parts of the United States, add 6 nine safety cars had been put into the field; by October 1910 first-aid-training work was being done in mining regions. The Bureau eras able to function so promptly in its safety work largely because sections of the Geological Survey, which had been doing some coal-mine safety work since 1907 or 1905, were transferred into the Bureau when it began to operate in July 1910. On October 30, 1911, a national First-Aid Meet was held at Pittsburgh, Pa., at which first aid and mine rescue were demonstrated. During the fiscal year 1910-11, the first year of the Bureau's existence, 509 persons were given certificates indicating completion of the Bureau's training course in first aid.

Jan 1, 1939