Search Documents

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By Glan Dale Coe, Will H. Coghill

"INTRODUCTION Characteristics of the mineral products that are to be contrasted herein are net energy consumed in grinding to a definite top limiting size and size distribution of the ground products. Through contrasts of these grinding characteristics this paper to differences in related mineral products and in unlike products. For,example, in anticipation of the data to follow, although Joplin chert and Babeitt taconits are running mates in defying the best crushing machinery, taconite is one of the more docile and Joplin chert one of the most refractory mineral products ordinarily fed to a grinding Routine grinding tests on a great variety of ores and tabulation of the findings have been covered amply by Lennox 4/ and by Maxon 5/ and associates. In contrast to that work, the present paper is a record of random tests made over a long period, and each answered an urgent question at the moment. The work was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama. The pressure of war work prevented an organized investigation."

Apr 1, 1943

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By James R. Kerr

Although metallurgical benefits of processing metals in a vacuum or reduced atmosphere have been realized for a hundred years, the problem of creating a vacuum in the range from 10-0 to 10-4 mm. of mercury in a moderately sized furnace chamber has been difficult to solve. The demand for these and lower pressures, with the advent of World War II, for separating the fission-able uranium isotope from its stable twin by the electromagnetic process, gave impetus to developing pumps capable of delivering extremely low pressures. With the release of data by the Atomic Energy Commission on methods of securing high vacuum in large equipment, steel companies took the initiative, and the growth of the vacuum-melting industry was assured. Vacuum-induction melting of steel in the United States began on a small scale in early 1945 and in 10 years grew to 60,000 pounds per month or 720,000 pounds per year. The years following 1954 showed tremendous expansion, culminating in 1958 in a capacity of more than 36 million pounds.

Jan 1, 1962

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By Clarence A. Wright, JAMES T. NORTON, JAMES G. PARMELEE

The object of this paper is to give to mining companies and to all others who are interested some idea of the possibilities in the treatment, by differential flotation, of lead-zinc ores of the Coeur d'Alene region and other districts. The purpose of these investiga.. tions is not to evolve a differential flotation process that would replace present methods of gravity concentration but rather one that could be applied to the relatively fine material and slime produced in the mills and treated unsuc_pessfully by gravity methods or by flotation. It is expected, of course, that the products to be obtained by differential flotation would be of much better grade than those now produced by flotation in the Coeur d'Alene mills. In view of the fact that it has been difficult to obtain representative samples of flotation feed from the mills, owing to the necessity of shipping the material wet and free from oil or other foreign matter that might be deleterious to the differential separation of the sulphides, the writers have felt justified in running flotation tests with the mill feeds in order to ascertain whether a differential separation of the sulphides could be effected. However, two different lots of flotation feed were tested for differential flotation, and the results of tests of one of these are given in this report. It is hoped that it will be possible later to test out the flotation feed for differential flotation on a large scale in some of the mills. This paper covers part of the investigations carried on by the United States Bureau of Mines in cooperation with the Idaho Bureau of Mines, the University of Idaho, and certain mining companies of the Coeur d'Alene region. Although the results of the tests included in this report are not to be considered final, they indicate possibilities and may suggest others leading to a solution of the problem of separating lead and zinc sulphides by differential flotation in the treatment of certain ores.

Jan 1, 1921

The coal reserve base is defined for coalbeds having sufficient thickness for underground mining within a depth range compatible with economic recovery. The reserve data are compiled by the Federal Bureau of Mines by updating and reevaluating previous estimates of the U.S. Geological Survey, State geological surveys, and others. Through the application of computer techniques, the tonnages are compiled by State, county, coalbed, and rank. Coal reserve base is allotted to sulfur categories by a statistical apportionment of data from available Bureau of Mines reports and records. The coal reserve base in those States east of the Mississippi River, minable by underground methods, is estimated to be 169 billion tons in coalbeds greater than 28 inches in thickness to a maximum depth of 1,000 feet. Excluding those coals in reliability categories other than measured and indicated, the underground reserve base includes 162 billion tons of bituminous coal and 7 billion tons of anthracite. Of the total, 27 billion tons contains 1.0 percent or less sulfur. Most of this low-sulfur coal is in the southern Appalachian area. Approximately 16 percent of the underground reserve base is without available analyses. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves. The purpose of this system is to provide a common yardstick for determining coal resources and reserves.

Jan 1, 1974

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in rescent years. The tenative ball-mill grindability method D408-35T4/ was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity.

Jan 1, 1938

By Albert L. Toenges, Louis A. Turnbull, Henry E. Dekay, James N. Scudder

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of Solid Fuels Coordinator and under the auspices of the Coke Production Committee indicated that a very appreciable increase in pig-iron production would be obtained if pres- ent blast furnaces were supplied with a more uniform coke. Control of the sulfur and ash content of coal used for making coke is an important factor in producing uniform coke and thus increasing blast- furnace efficiency. In some mines producing metallurgical coal, the analysis of the coal bed shows a wide range of sulfur and ash content. To obtain production of coal with minimum deviation in sulfur content sampling, grading, selective mining, blending, and surface preparation are practiced at some mines with satisfactory results. The mines selected for this study have developed these methods and are successfully producing coal of uniform sulfur and ash content. The systems employed at different mines vary according to the physical character- istics of the coal bed, the manner of occurrence of impuritites in the coal, the development plan and mining system, surface preparation and the acceptable impurity content of the prepared coal. The ash content of the coal can be controlled by face preparation and in the cleaning plant. The introduction of some method or practice at other mines might make possible the use of coal for inetallurgical purposes that otherwise could not be used for making coke because of the wide variation of sulfur and ash content.

Dec 1, 1943

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with detachable bits.]

Jan 1, 1941

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By E. P. Youngman

The basic mining law of Esthonia is the law that was passed by the Parliament (Riigikogu), or State Assembly, on March 17, 1927 (effective Avril 1, 1927), superseding the Russian Mining Law Book VII of the Code) issued in 1912. References in this digest are only to articles of the Law of Merch 17, 1927. However, the law concerning all industrial enterprises (Riigi Teataja No. 28, 1920, Law No. 106) governs not only mills and refineries but also mining operations themselves (arts. 2 and 3). No access was ad to that law. Esthonia is not well supplied with minerals; its industries are primari- ly agriculture and dairy farming. Natural gas, prites, lead, zinc, iron ore, salt, and mineral waters have been found but never as yet in deposits of commer cial size. The production of oil shale is of some importance; and peat, which covers as much as 5 per cent of the total area of the country, is mined in sub- stantial quantities. Cement rock, gypsum, fire clay, and phosphate rock likewise are produced, though only on a small scale.

May 1, 1930

"Status of the Mineral Industries" provides a written and graphic view of the Nation's mineral position and its mineral industries. The report, issued annually by the Bureau of Mines, U.S. Department of the Interior, describes recent activities in mineral production, consumption, imports, exports, and uses of significant minerals and mineral raw materials. Charts profile trends for the past 28 years in supplies and uses of iron, steel, major nonferrous metals, primary nonmetallic construction raw materials, fertilizers, and plastics. Also included are current and historical financial data on the mineral industries, such as debt-equity ratios, asset-to-liability ratios, and plant and equipment expenditures.

Jan 1, 1979

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By R. L. Marek

The number of Persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By R. L. Marek

The number of persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from, comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be. available, the Bureau has established schedules of minimum requirements for oxygen breathing apparatus,3/ gas masks,/ supplied-air respirators (hose masks, air-line, respirators, and abrasive blasting helmets, hoods, or masks),5/ and dispersoid (dust, fume, and mist)

Jan 1, 1943

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992