Search Documents

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By F. D. Wang

This report presents a structural-mesh-generating computer program for the two-dimensional finite-clement method of mine structural analysis of single and multiple openings in nonhomogeneous rock mass. This program greatly reduces the amount of input data required and the chances of error which otherwise are large owing to the large amounts of data and the complex mesh involved. The program description, a user's guide, example problems, and program listing are included.

Jan 1, 1971

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

This report is the 21st in a series summarizing research and technologic work on coal and related investigations by the Federal Bureau of Mines - the Chard of the series published on a calendar-year basis 2/ Subject publica¬tions of the Bureau during 1956 are cited, and pertinent Bureau work is described briefly. The most effective method of conserving our important coal reserves is through improved technology of production and utilization. Associated problems form the program of the Bureau.3 4 5 6/ Potential production is depend¬ent on a knowledge of the quantity and quality of the reserves, and the Bureau continues to contribute information on this subject. Many problems are being studied that relate to improvements in current production, including mining methods and health and safety measures. Preparation of mined coal is necessary for its most efficient utilization. Preparation by conventional methods is being studied, as well as the development or new methods. Fundamental studies on the structure and properties of coal are necessary to insure full advantage of the special qualities of different coals. Controlling factors in the efficient use of coal in combustion, carbonization, gasification, and direct and indirect hydrogenation of coal are being studied continuously, and new processes are being investigated. The many advances in all these fields are discussed.

Jan 1, 1959

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By Emory Smith

The Victorville cement plant of the Southwestern Portland Cement Co. is located about 1 mile from the city of Victorville, Calif. Two transcontinental railway systems, the Atchison, Topeka & Santa Fe, and the Southern Pacific Railroad, afford shipped facilities. The plant is modern and well kept, as the officials, especially the higher operating officials, take pride in the appearance of the place. Dust has been practically eliminated by the installation of dust collectors and wet grinding. The plant has a rated capacity of 5,000 barrels of cement daily.

Jan 1, 1929

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By David A. Hill, James R. Wait

This report contains a summary of analytical research on electromagnetic methods of nondestructive testing of cylindrical conductors. The principal objective is to provide theoretical insight to the operation of electromagnetic sensing of the internal properties of wire ropes that are used extensively in mine hoists. An overall review of past work is also included.