Search Documents

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

By Xinquan Zhou, Rudolf E. Greuer

MFIRE, written in Fortran 77, is a computer program for ventilation state simulation in the steady state or transient state condition. It can be applied for the calculation of normal ventilation system planning or the analysis of the dynamic state variation in a ventilation system under thermal or mechanical disturbance. The state simulator MFIRE is a useful tool for mine fire fighting. In the case of a mine fire, mine ventilation engineers want to get some help to obtain more information, such as what is happening in the underground mine and how to control the mine fire, for correct decision making. By use of program MF'IRE, forecasts can be made on the variation of airflow, temperature, and contaminant distribution in a ventilation system during a mine fire. The paths which the contaminant takes at each time interval can be traced. The program MFIRE can be of assistance in the preplanning of escape routes. It can also be helpful during a mine fire emergency and mine recovery operation. Besides of offering the information of state simulation during a mine fire, MFIRE can be applied for state control by pretesting the suitability of the selected state control measures. It is to simulate the effects of the state control measures on the airflow distribution of a dynamic ventilation system. The testing result can be used for fire fighting in a similar real case of a mine fire. By employing empirical methods or a qualitative analysis like Budryk approach, ventilation engineers can choose different combinations of locations and sizes of control devices as samples of state control for an underground mine fire. Program MFIRE can simulate the different combination samples, that consist of a certain mine fue, the corresponding different control measures, and obtain the control effects. After the different control results are compared, the state control measure, which creates the best effect among the different state control measures, will be chosen for that fire case. When a mine fire, which is similar to one of the pretested cases, breaks out, the corresponding choice of the state control measure is applied to the ventilation system. It means that the simulator MFIRE has the function of indirect state control [10]. To achieve the above two functions, state simulation and state control, the mine ventilation system condition, sometimes, should be changed in a wide range to meet the requirement of the fire fighting. These wide system condition changes, such as adding operating fans, stopping or reversing fans, changing fan characteristics, adding regulators and making airflow shortcuts are represented in the time table of the input data set When the data files are changed in a wide range, however, an iteration divergence and some other computing errors in the distribution of airflow, temperature, and contaminant may occur. More serious logical programming and flexible selection on the algorithms are wanted to meet the request of the different data sets, to achieve correct state distribution simulation and improve the iteration convergence. To enhance the reliability and common suitability of program MFIRE, it is necessary to make investigation, analysis, and modification for the formal versions of MFIRE. The version 1.29, permitting dry .calculation, and versions 2.01/v2.0, permitting dry and humidity calculation, are widely applied

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By Chas. F. Jackson

This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the United States Bureau of Mines and made possible through the cooperation f many mining companies in the United States and foreign countries. The preparation of this paper follows a field study of top-slice mining during which the author visited and discussed with operating officials a large number of iron mines in the Lake Superior region. During this study special note was made of changes in top-slicing practice during the past decade, prior to which the author had acquired several years experience with the method through active connection with a number of mines employing top slicing.

Jan 1, 1931

By E. D. Gardner

This is one of a series of paper's being published by the Bureau of Mines on placer mining; it is written as a supplement to Information Circular 6788, "Placer Mining in the Western United States, Part III", by E. D. Gardner and C. H. Johnson which was published in February 1935. Since Information Circular 6788 was written (1933), considerable advance has been made in the technique of mining placer gravels with power shovels and draglines. Although new washing plants continue to be built in accordance with untried designs the trend of new installations is toward proved equipment. A substantial number of plants are now being operated successfully (1937).

Jan 1, 1938

By J. S. Miller

This report presents a complete coverage of results from Bureau of Mines preliminary research and the field application of explosive fracturing techniques to prepare oil shale for in situ recovery of shale oil. Small-scale surface tests were conducted to determine the feasibility of using a nitroglycerin-base explosive for creating rock fractures. Prior to underground testing, surface and near-surface tests with liquid explosives showed that explosions in sheetlike layers simulating underground fractures would propagate effectively. Successful surface experiments were conducted using layers of explosive placed between glass plates and explosive-saturated sand confined in small-diameter metal tubes. The tests in glass-plate reservoirs and metal tubes demonstrated that nitroglycerin would detonate and the explosion would propagate in cracks as thin as 1/32 inch and through distances up to 12 feet. In a shallow field test, nitroglycerin was detonated in a vertical crack in limestone and produced extensive fracturing. Explosive fracturing tests were performed in oil shale formations on seven sites near Rock Springs, Wyo. The procedures included (1) displacing and detonating nitroglycerin in natural or hydraulically induced fracture systems; (2) detonating nitroglycerin in wellbore shots; (3) displacing and detonating nitroglycerin in induced fractures followed by wellbore shots using pelletized TNT; and (4) detonating wellbore charges using pelletized TNT. The research on oil shale formations demonstrated that nitroglycerin displaced in a natural or hydraulically induced fracture would detonate, and the explosion would propagate through the explosive-filled fracture. Shooting a pattern of wells in oil shale at 100-foot depth with wellbore charges of pelletized TNT developed a satisfactory interwell fragmented zone. Tests performed on other sites at depths to 385 feet caused fragmentation of rock around the wellbore and provided interwell communication. Fourteen methods used to evaluate the extent and degree of fragmentation in the explosive fractured oil shale are discussed.

Jan 1, 1974

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946

By Lorraine B. Burgin

This study by the Bureau of Mines documents the leadtime required for preliminary and detailed exploration, development of the mine, and construction of beneficiation and support facilities for selected copper deposits in Arizona. The time for major exploration ranged from 1 to 15 years, time for open pit development (or construction) was 1 to 4 years, and time for under- ground development was 4 to 8 years; one underground mine presently being developed may require 12 years to achieve production. Construction of the beneficiation plants required 8 months to just over 2 years. The data are supported by historical facts for each deposit during the leadtime stages from location of claims through exploration, construction, expansion, and leaching. The sequence of development and factors contributing to differences in the time spans are discussed. Histories are detailed for the Miami, Castle Dome, Copper Cities, San Manuel-Kalamazoo, and Twin Buttes properties; briefly summarized are the Pinto Valley, Miami East, Esperanza-Sierrita, Pima, and Mineral Park Properties. Each mining operation had its own pattern of development, and together they present a source of planning information for the development of other properties.

Jan 1, 1976