Search Documents

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

By Jack Wasserman, Don Wasserman, Logan Mullinix, Shekhar Khanal, Kelly Neal

This paper presents current finding on truck driver average exposure to acceleration for several different manufacturer’s cab-over trucks on a variety of roads in different countries. The predominant time, for this aspect of the study has been spent in the area around London, England and Warsaw, Poland. The ECE directive 2002/44/EC has provided specific guidelines for vehicle operators 8 hour average acceleration exposure. The primary considerations have been on truck design including the air-ride driver’s seat. The truck manufacturers have produced truck cabs that have some separate suspension from the truck frame. The truck seat manufacturers have been producing air-ride suspension seats for the cab. Both of these designs have had the objective of meeting the ECE directive and providing the vehicle drivers with some degrees of comfort. This paper will provide some information on the ability of the vehicles to operate on a variety of roads and meet the objectives. Method The primary method for evaluation of the driver’s exposure has been the use of a seat pad attached to the driver’s seat. Although this sensor system provides the critical information for the driver, an understanding of the reasons for the values requires additional measurements. The initial study in England used both driver and passenger seat pads, as shown in Figure 1, as well as triaxial accelerometers mounted on the base of the seat. The latest studies used significantly more transducers to better understand the relative rotations and translations on the truck frame, the cab, and the driver. [ ]

Jan 6, 2006

This project was started 8 June 1971. As set forth in our Proposal of 28 April 1970, responding to the RFP of 30 March 1970, the plan was twofold: 1) choose fluids and develop techniques for measuring coat porosity, and 2) construct a porosimeter for making such measurements, By the time plans for the porosimeter had been drawn up, the picture had changed; and it was found more advisable to do further researches on porosity rather than build the equipment. This development arose from a meeting with Dr. Fred N. Kissell on 14, 15 October 1971, annotated in our letter of 19 October 1971, and was contracted for 6 December 1971. The technical effort of the project was completed 7 May 1972. From the beginning it was realized that the ratio of 'hole volume to the whole volume' might be too simplistic a definition for coat porosity and that its measurement might be confounded by complications which were not yet known, We were hopeful that an exploration of fluids and techniques would provide early feedback on both these points which could be used in subsequent developments. This turned out to be the case.

Jan 1, 1972

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

This publication summarizes the in-house and contract research and development projects programed for fiscal year 1981 by the Bureau of Mines under its Minerals Environmental Technology activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau?s environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. The environmental research and demonstration activities of the Bureau were consolidate in 1979 with the formation of the Minerals Environmental Technology program, which is directed toward the elimination or reduction of environmental problems associated with the extraction and processing of minerals. Among the efforts underway are development of data and technology for assessing the potential environmental impact of minerals development, for monitoring minerals extraction operations, and for establishing viable reclamation requirements on abandoned mine lands; development and demonstration of technology 'or control of environmental disturbances during minerals extraction operations; development and demonstration of land reclamation and mine closure techniques to restore or enhance the productive use of mined lands; development of engineering techniques that incorporate state-of-the-art mining environmental technology in the design and planning of minerals extraction operations; development and demonstration of new mining systems that greatly reduce or eliminate the adverse environmental impacts of minerals extraction; and providing the technologic base for Federal, State, and local establishment of environmental standards for mining operations. Included in the minerals-processing-related work are projects to clean mineral-processing waters: demonstrate a Bureau process for scrubbing SO from powerplant stack :;as; recover dissolved minerals from process streams; stabilize discarded dusts, slags, and tailings: remove hazardous contaminates from byproduct wastes; reduce generation of waste solids; and improve metallurgical process engineering to eliminate pollution. Approximately $21 million was appropriated for this work in fiscal year 1981.

Jan 1, 1981

By F. A. Rutledge, H. Marstraander, J. H. Hulbert, G. A. Apell

"INTRODUCTION The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska caused the Coal Procurement Section of the Alaska Department, U. S. Army, to be established. It proposed to investigate the coal deposits and to expedite production of coal. The Bureau of Mines has closely cooperated in this program and was in direct charge of exploration. As to develop and equip an underground coal mine would have taken time and the need for coal was acute, a deposit that could be prepared for mining quickly was desirable. Several such deposits of stripping coal were known to occur in the Nenana field and were examined by the Bureau. One of these, the Diamond strip mine 4 miles west of Healy, was brought into production late in the fall of 1943. This mine was operated for the Army Coal Procurement Section by the C. F. Lytle Co. and the Green Construction Co.The Roth property, or Leasing Block No. 28, in the Healy Creek Valley offered the largest available tonnage of both stripping coal and total reserves. A program of exploration by the Bureau of Mines was inaugurated in 1943 and completed in 1944. Field parties of the Federal Geological Survey mapped the area had correlated the coal beds during the 1944 and 1945 summer seasons."

Nov 1, 1946

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By Joseph Daniels

[Adequate supplies of suitable coal and coke are prime requisites in many industries, particularly those dealing with the utilization of mineral resources, recently interest has been focused on the possibilities of using electricity produced at Bonneville and Grand Coulee, Wash., in many electrochemical and electrometallurgical processes, in which core or some form of carbon is necessary in addition, discussion has been revived on the possibility of making iron and steel by the conventional methods employed in blast and open-hearth furnaces. The subject also is important at this time because of its relationship to industrial preparedness for national defense. A supply of coke from local sources on the Pacific coast is necessary in any program of production for strategic sufficiency of certain materials. An anal trio involving tae establishment of such industries should include detailed data on available supplies of coal, the quality and properties of the coke produced, and the technologic and economic factors involved in manufacture of echo and disposal of byproducts.]

Jan 1, 1941

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department?s Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987