Search Documents

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Jeff Peterson, Alastair Grogan

During the winter of 2001/2002, a number of seismic exploration projects were carried out in the Mackenzie River Delta area of the Northwest Territories, in Canada. The purpose of the seismic projects was to identify potential drilling targets for subsequent drilling programs, using explosives as a seismic source. Recent changes to fisheries regulations meant that blasting under lakes, the Mackenzie River and offshore from the delta, was not allowed to induce water overpressures in excess of 100 kPa in these water bodies, and that a water overpressure monitoring program had to be conducted to confirm that this requirement was being met. This paper describes the water overpressure monitoring program on one of the exploration projects, presents the results of the monitoring, and discusses the challenges of carrying out this work in the middle of an arctic winter.

Jan 1, 2003

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By Greg Parker

"As the Explosives Industry continues to evolve and condense, those involved, such as Blasters,Contractors, Distributors and Consultants, continue to be challenged by both internal and externalforces. Increased pressure by government agencies, higher safety standards, new levels of technology and mandatory certification programs, are forcing us to expand our awareness and increase our levels of efficiency. These higher standards require increased awareness. Increased awareness requires better training programs and better supervision with emphasis on production and the employee. This means the desire to improve must be instilled from the top down. this paper will explore the current impediments to this goal and discuss the possible solutions for achieving greater safety awareness, increased production and higher levels of personal achievement. Through the use of audio/visual aids, I will attempt to show the discrepancies as well as the solutions."

Jan 1, 1999

By N. Powell, P. Hunt, A. Wetherelt

This paper considers the current methods of analysis employed, the validity of assumptions made and the reliability of results and predictions derived; where appropriate, alternative methods are proposed which are more accurate and can be applied with greater confidence. In regard to data collection, new local blasting data has been analysed and conclusions drawn but, due to the restricted amount of space available, reference to data set A only has been made in the text. The problem of mathematical model choice is considered and results for two and three parameter power laws are compared. The very important matter of parameter determination is discussed fully, with major emphasis being placed on the comparative merits of log-log linear, log-log planar and direct power law regression. Supporting data analysis examples are included. Assumptions regarding the normality of ‘best-fit’ regression model residual distributions are questioned and the reliability of associated safety limit determinations is discussed.

Jan 1, 2003

With the ever increasing problems of narrowing profit margins, and increased liability, a solution/option to SEE members is needed. It is essential that all members understand the benefits of utilizing explosives in combination with other methods of achieving the required result on difficult rock or concrete removal projects.

Jan 1, 1995

By Ankit Jha, RICHARD AMOAKO

In this paper, we examine the challenges associated with the use of empirical rock fragmentation models. We highlight key parameters omitted by these models, and propose a machine learning approach that incorporates these parameters, leading to a simple, yet more accurate approach to blast design.

Feb 1, 2020

By Lyall Workman

"Many new technologies, useful to the mining and quarrying have recently come to market. Some are applicable to drilling and blasting operations. Others apply to subsequent mining unit operations and can generate data for objective assessment of blasting results. These new technologies can accurately capture the information component of blasthole drilling, andindeed of each unit operation. Knowledge can be extracted from this information and passed forward and back through the mining system to improve operations and factually assess results. This leads to an evolving and improving system."

Jan 1, 2001

By Norm Tienkamp, Normand Martineau

Through the normal course of operation, mine operators are living situations where blast results need to be measured. It becomes the supervisory group responsibility to select evaluation parameters with appropriated and available technics. In Mine Selbaie's case, we have retain the following parameters: rock fragmentation, oversize fragments, rock pile movement, grade rupture.

Jan 1, 1996

By Brian W. Stump, David P. Anderson

Identification of seismic events detected under a Comprehensive Test Ban Treaty requires a clear physical understanding of the different types of seismic sources including mining explosions, rock bursts, mine collapse and small, shallow earthquakes. Constraint of the operative physical processes in the source region and linkage to the generation of seismic waveforms with particular emphasis on regional seismograms is needed. In order to properly address the multi-dimensional aspect of data sets designed to constrain these sources, we are investigating a number of modern visualization tools that have only recently become available with new, highspeed graphical computers that can utilize relatively large data sets. The results of this study will provide a basis for identifying important physical processes in the source region that contribute to regional seismograms.

Jan 1, 1995

By Ian R. Firth

For the majority of open pit precious metal mines in the western United States, grade control practices have evolved as a direct result of the variable geology of the ore body and the lack of a clear visual or geologic distinction between ore and waste material. These practices often include the extensive use of buffer or choke blasting, in an attempt to minimize lateral movement of the muckpile. The Mackay School of Mines is conducting ongoing research, which aims to develop a practical method of measuring the movement of discrete “targets” placed within the body of the blast. The movement experienced by these targets can then be used to interpolate the movement of the blast as a whole. Typically, the boundaries between different material types are known as digging limits or polygons and are marked using colored flagging on the muckpile. If material movement can be measured using targets placed in the blast, these digging limits can be altered to reflect the blast-induced rock movement, reducing dilution and improving value recovery.

Jan 1, 2002

By Roberto Golchi

This article describes the method used to quantify the Environmental Impact for the mining, by drilling and blasting, of a borrow pit for a gravity-dam. The affected environment was broken down into a number of components, such as public health and safety, social relationship, air and water quality, flora and fauna. The effect of the various impacting factors from the mining activities, both directly and indirectly, was then calculated for each environmental component. To do this, each impacting factor was first given a magnitude, a number based solely on the range of scenarios possible for the impacting factor. A matrix of weighting factors was then derived to systematically quantify, and normalise, the effects of each impacting factor on each environmental component. The overall impact upon each individual environmental component was then calculated by summing the weighted magnitudes for all the impacting factors.

Jan 1, 2003

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Paulo Couceiro, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper describes a new methodology to assess rock mass-quality to guide blasting in open pit operations. A developed Structural Block Model and Strength-Grade factor have been combined in a Rock Factor, that, exclusively obtained from drilling data, can provide an automatic assessment of rock structure, strength, and waste/ore identification.

Feb 1, 2020

By Duan Baofu, Wang Xuguang, Song Jinquan

In this paper, the model of optimizing selection on preparation of Powdery Emulsion Explosives(PEE) is established by the Neural Net Theory(NNT). On the basis of some data in the study of PEE, the training, prediction and optimizing selection of the Neural Net (NN) model are finished by a compiling procedure. The results indicate that the model is helpful to the preparation of PEE and worthy to extend and apply broadly. KTYWORDS Neural Net Powdery Emulsion Explosives Preparation Optimizing Selection

Jan 1, 2003

By David R. Ziegler

The concept and facts concerning "threshold blast damage" are not considered "general knowledge". Perhaps because of a lack of knowledge, understanding, and experience of blasting effects, property owners and lay-persons may attribute a wide range of common cosmetic conditions to "blasting damage".

Jan 1, 1997

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By Matthew Hirsch, Jason Connot, Nathan Rouse, Srivatsan Jayaraman, Akash Adhikari, Brent Meins, Purushotham Tukkaraja

The Deep Underground Neutrino Experiment (DUNE) is a world-class particle physics research project currently being constructed 4,850 ft, 1,478 m underground at the Sanford Underground Research Facility (SURF), former site of the historic Homestake Gold Mine in Lead, SD. Construction for the project involves drill and blast excavation of 800,000 tons of rock to house neutrino detecting cryostats adjacent to on-going particle research and sensitive lab areas. To protect nearby labs during the planned 4 years of blasting operations, project specs required installation of six steel, heavily reinforced blast doors designed to withstand 20 psi blast loads. This research aimed to quantify the pressure reduction across the blast doors and more accurately model underground blast wave propagation. 827 blasts to date have been monitored at eight locations on the 4850 level of SURF with some locations behind blast doors and some in front. Additionally, pressure measurements directly in front of and behind one blast door were taken during 94 blasts.

Feb 6, 2023

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By Douglas A. Bartley, Davey Bickford, Raphael Trousselle

The long awaited arrival of a high accuracy detonator to reach the explosives end user will provide new opportunities the blasting community to become better equipped and able to improve upon the current approaches and methodologies used in blast design as they apply to the mitigation of adverse effects from blasting. This paper will detail the approach and findings throughout a several month research project to quantify the high accuracy detonator benefits and to mitigate a long standing vibration problem at a hard rock stone quarry in the state of New York. The tests conducted in this study were designed to provide important information as to the relationship between the use of high accuracy detonators and overall blast performance in terms of ground vibration prediction, control and improved rock fragmentation.

Jan 1, 1998

By P Geddes, K Grohs, C K. McKenzie, M Morrish

Low grade surface gold mining at the Acacia Resources, Union Reefs Gold Mine in Australia's Northern Territory, involves the excavation of benches in three slices after blasting. Blast patterns span zones of high and low grade ore, as well as zones of waste, and selective excavation is required in order to maintain economical head grades for the carbon-in-leach processing plant.

Jan 1, 1998