Search Documents

By Erik K. Lauritzen, Jorgen Schneider, Niels Madsen

From 1986 to 1988 Kalaallit Tunisassiorfiat (KTU)/Gronlands Hjemmestyres Produktionsvirksomhed (the part of Greenland's own governing body which is in charge of production activities) has been responsible for blasting projects in the following 4 towns: Ilulissat/Jakobshavn, Qasigiannguit/ Christianshab, Qeqertarsuaq/Godhavn, Sisimiut/Holsteinsborg

Jan 1, 1989

By Jack Eloranta

This paper compares energy requirements for blasting, crushing and grinding. By tracking electrical consumption for various powder factors, a general trend has appeared. This study involves over 100 million tons of ore and powder factors ranging from .5 lbs/LT to .8 lbs/LT. Actual energy usage is compared to predicted energy based on the Bond equation.

Jan 1, 1997

Tracer blasting is commonly used in Canadian underground mines for overbreak control. It involves tracing a column of ANFO with a low strength detonating cord. In order to investigate the effectiveness of tracer blasting in perimeter control and to understand its mechanism, a field experimentation was conducted which involved drifting, benching and pipe tests.

Jan 1, 1994

By Rick W. Bellenie, Ronald L. Woolf

The Gregg River mine is located 40 kilometres (25 miles) south of Hinton, Alberta, approximately 330 kilometres (205 miles) west of Edmonton and lies against the Front Range of the Rocky Mountains.

Jan 1, 1994

By Michael E. Curtis

This paper outlines a study performed to analyze the advantages of utilizing a blasting agent with a velocity of detonation that is 1.3 to 1.4 times the P-wave velocity of sedimentary shales and sandstones at a major Midwest coal operation.

Jan 1, 1997

By Antonio S. Aldana Selders

With special designed explosive and a system to lower down a heavy load of Explosives through 8" pipe results are achieved, the stimulation of sulphur production takes place. Well # 18-1063 at 515 meters below ground is loaded with 802 units of explosives with total weight of 1820 kilos to fill up the column of 93 meters of limestone & sulphur strata.

Jan 1, 1995

By Edward Jr Walter

This paper discusses the problems that arise in the process of developing adequate explosives noise legislation. Case histories are used to illustrate how and where these problems arise and the course of action followed in overcoming them. It is imperative that those concerned keep informed as to possible legislation and be prepared to present solid facts that will insure fair and reasonable controls.

Jan 1, 1975

By James R. Kennedy

The recent drop in world gold prices is driving many northern Nevada underground gold mines to look for new ways to improve and enhance current mining operations. Continuous improvement programs at these mines are finding the means to increase mine productivity while reducing total production cost. This paper looks at developments in the drill and blast program at Independence Mining Company’s Murray mine.

Jan 1, 1999

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981

By Yves Lizotte, Malcom Scoble, Pierre Michaud

The concept of optimum fragmentation in surface mining operations, i.e. the degree of fragmentation to which corresponds the lowest overall associated costs of drilling, blasting, loading, haulage and crushing, was developed more than thirty years ago. Recent field investigations using novel technologies, which have been completed by ICI Explosives Canada and by others, indicate that this ultimate goal of optimum fragmentation is closer to becoming reality.

Jan 1, 1997

By T Michael LeBlanc

Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of this deviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (302 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution.

Jan 1, 1996

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Norman S. Smith, Troy D. Harris, Richard L. Ash

In open-cut bench blasting drilling boreholes below grade level is normally considered essential to insure toes do not remain. The extra drilling and use of explosive below floor level are not only expensive but on occasion cause serious problems including severe floor damage and excessive ground vibrations. It has been reported that under certain circumstances explosive in the subdrilling has been successfully substituted by broken rock with its associated benefits.

Jan 1, 1978

By Everett Clausen, Richard Walker

CIL/EVANinc and the Canadian Explosives Research Laboratory of the Government of Canada have evolved a concept developed by Research Energy of Ohio, into a landmine neutralization system that is the most innovative to date.

Jan 1, 1999

By Rodney C. Espley-Jones, John C. B Wilson

South Africa is well known for its shaft sinking exploits, and many of the world's biggest and deepest shafts are to be found there. Blasting practice differs in a number of respects from that followed elsewhere.

Jan 1, 1979

By C H. Ryu

This paper presents a simplified two-dimensional numerical model of block fragmentation in a Jointed rock mass during the late or throw stage of a blast after wave effects have subsided. The model is based on the distinct element method. Examples illustrate the approach and allow for a comparison of effects of Joint patterns on fragmentation and resulting block motion.

Jan 1, 1986

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Roger L. Keller

This paper examines the aspects of differing types of blasting cuts in underground headings with consideration to the reduction of number of holes and costs. At least one comparison study is related where costs per advance meter were significantly improved. The technical aspect of the paper covers a study of the effects of various blasthole delay intervals on resulting crater volume, ground vibration, and fragmentation for six hole V-cuts.

Jan 1, 1989

By He Guangyi

During rock blasting in extending deep cutting from Jiu Li Mountain to Dong Zhuang Village in Jiao Zhi Railway line, we have drilled deep hole with large scale diving drilling machine and successfully carried on controlled blasting. This has provided new experiences for rock blasting in extending existing cutting. The aim of this article is to provide an introduction to bench height, blast holes arrangement, powder charge calculation, and detonating technique during blasting.

Jan 1, 1997

By Jon Andrews

Purpose: To show how in managing risk in avalanche control blasting has changed throughout the years, and try to define the term “Acceptable Risk”. History: The history and the way we manage risk in avalanche control blasting to the avalanche control crews and public has change over the years dramatically. From the mid 1800s to about 1920 was the Risk vs. Rewards era, the Industrial Revolution. Now it is a Risk vs. Liability, the age of Liability.

Jan 1, 2009