Search Documents

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By J. E. Scott, L. M. Heaman, R. A. Creaser, G. S. Salazar

"Schaft Creek is a calc-alkaline porphyry Cu-Mo-(Au) deposit located in northwestern British Columbia. The deposit formed in a volcanic arc setting, likely on a back-arc rifted continental fragment. It is hosted by Late Triassic basaltic to andesitic volcanic rocks of the Stuhini Group (Stikine Terrane), and is associated with porphyritic granodiorite dikes emanating from the nearby Hickman batholith. The age of the Hickman batholith is approximately constrained here by a composite U-Pb zircon date of 222.1 ± 9.6 Ma, which is in broad agreement with a well-constrained age for mineralization at Schaft Creek of 222.0 ± 0.8 Ma (Re-Os molybdenite). The deposit is in most respects typical of calc-alkaline porphyry systems, but displays silica-poor sericite-chlorite alteration in mafic country rocks in place of classic phyllic altera¬tion. The deposit comprises three distinct, but related, zones: the northern Paramount zone, the Main zone, and the West Breccia zone. Two phases of mineralization are observed. The first phase occurs as hydro-thermal veins and breccias, and minor disseminations. It consists of bornite, chalcopyrite, molybdenite, and pyrite with potassic and sericite-chlorite alteration. The second phase is minor and consists of veins of molybdenite ± specularite, as well as Cu-Pb-Zn sulfide veins without any significant corresponding alteration. Extensive structural modification has affected the deposit both during and after its formation.Schaft Creek est un gîte porphyrique de Cu-Mo-(Au) calco-alkalin situé dans le nord-ouest de la Colombie Britannique. Ce gîte s’est formé dans environnement d’arc volcanique, probablement situé sur un fragment continental bordé par un bassin d’arrière-arc. Le gîte est encaissé par les roches volcaniques basaltiques à andésitiques du Groupe de Stuhini (Terrane de Stikine) d’âge Triasique tardif, et est associé à des dykes de granodiorite porphyrique provenant du batholithe de Hickman avoisinant. L’âge du batholithe de Hickman est estimé par un âge U-Pb composite sur zircon de 222.1 ± 9.6 Ma, lequel est grossièrement en accord avec l’âge de la minéralisation de Schaft Creek, estimé a 222.0 ± 0.8 Ma (Re-Os sur molybdénite).Ce gisement, bien qu’à plusieurs égards typique des systèmes porphyriques calco-alcalins, présente une altération en séricite-chlorite pauvre en silice dans l’encaissant mafique a la place de l’altération phyllique classique. Ce gîte comprend trois zones distinctes bien que connexes : la zone Paramount au Nord, la zone Principale et la zone West Breccia. Deux phases de minéralisation sont observées. La première phase se présente sous forme de veines et de brèches hydrothermales ainsi qu’en disséminations mineures et consiste en bornite, en chalcopyrite, en molybdénite et en pyrite avec une altération potassique et en séricite-chlorite. La seconde phase est mineure et consiste en veines de molybdénite ± spécularite ainsi qu’en veines de sulfures de Cu-Pb-Zn sans association à une altération particulière. Le gisement a été profondément modifié par la déformation a la fois durant et après sa formation."

Jan 1, 2008

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By Tim Hughes, A. H. (Sandy) Gray, Jennifer Abols

"The selective recovery of gold and silver from solutions containing other metals such as copper is possible using AuRIX®100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated opening the possibility of producing high grade gold doré from high grade silver pregnant leach solutions. This paper reviews the AuRIX®100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX®100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX®100 is being tested.INTRODUCTIONGekko SystemsGekko Systems specializes in the design, development and distribution of innovative mineral processing equipment and systems with a particular focus on gravity separation for the gold and diamond industries. The company, which has been around since 1996, has five main products: the InLine Pressure Jig, the InLine Spinner, the InLine Leach Reactor (ILR), Gekko Resin Column and Modular Systems.The InLine Leach Reactor is an intensive cyanidation reactor that uses high cyanide (0.5 – 2 % NaCN) and high oxidant (20 ppm dissolved oxygen as O2 or hydrogen peroxide) to dissolve gold from medium and high-grade gravity or flotation concentrates. The ILR, which typically replaces a shaking table in the gold room, is available in both batch and continuous models. There are 42 installations worldwide. Further details on this technology can be found in papers written by Gray et al (2003) and Longley, McCallum and Katsikaros (2003). By replacing a shaking table with an ILR, the overall gravity and plant recoveries can be increased significantly. Other advantages include reduced security risks, lower operating costs, reduced operator involvement due to the automatic process and increased safety for gold room operators."

Jan 1, 2006

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara's original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara's concentrator and processing equipment was adequate to meet requirements;4. Tara's mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By G. Zhu

The straight Y-shaped silica nanorods have been synthesized on Si wafer by thermal chemical evaporation of mixed powders of silica and graphite at 1300_ and condensation on Si substrate without assistance of any catalyst. The synthesized samples were characterized by means of scanning electron microscopy, transmission electron microscopy. The results suggested that the straight Y-shaped silica nanorods have uniform diameter about 50-200nm and neat smooth surface. The growth of such silica nanorods may be a result of the fluctuation of external conditions and internal structure faults causing a change in the growth direction of silica nanorods developed.

May 1, 2008

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By L. D. Eccleston

Any man-made structure will eventually decay, but we are basically concerned with the prevention of corrosion within a fairly limited time span. How corrosion can be minimized by design, the removal of oxides and a careful choice of paint systems is discussed, and mention is made of the electrical nature of most anticorrosive systems. Also discussed are the characteristics of certain paint binders and how mechanical properties will differ for various environments. Corrosion of a substrate by acidic breakdown products of some paints is mentioned in conjunction with a discussion on convenience versus ultimate performance. A brief mention is made of the three main components of a paint system, and the principal types of paint are placed in broad categories, with the main strength and weaknesses of each type listed.

Jan 1, 1979

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By P. G. Claridge, R. A. Tenbergen

"Pipe Open Pit ore is delivered by rail to the Thompson Mill at a rate of 34,000 tons per week. Ore is milled at a rate of 220 tons per hour.Characteristics of the serpentinised peridotite host rock are such that significant deviations from hitherto experienced milling practice became a necessity because of coagulation of the gangue upon cominution.Extensive development work was done in the grinding and classification circuits to better understand the ore characteristics and optimize operating parameters and the use of available equipment. This work ultimately resulted in the change from 30 to 20-inch diameter cyclones.Coagulation of the ore slurry and the characterstics of the sulfide minerals necessitated an ""unconventional approach"" in processing as compared with the beneficiation of Thompson Mine ore.Recent changes in ore characteristics led to testing of antistatic agents to reduce tailing losses."

Jan 1, 1975