Search Documents

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

By B. Samanta

Abstract - Ore reserve estimation, based on sparse drill hole data, was conducted for a placer gold property in Nome, Alaska. A problem with sparse data is that random subdivision of the data into modelling and evaluation subsets (as is commonly done) becomes a problem, as random selection may result in biased/skewed subsets. Therefore, a technique that combined data segmentation with genetic algorithms (GA) was applied to divide the samples into three equivalent subsets: training, validation and testing. Data segmentation was done on the basis of the distribution of gold values. Neural network and a variety of kriging techniques were used to estimate gold grades. A multi-layer feed forward neural network along with "early/quick stop" training was used for neural network modelling. A comparative evaluation of kriging and neural network methods was then performed. The results revealed that neural network was generally superior to the kriging techniques for gold grade estimation in the Nome deposit.

Jan 1, 2002

By V. “Ram” Ramachandran

"In view of the increasing number of environmental regulations that have been promulgated all over the world in the last thirty years, non-ferrous smelters and refineries have had to learn and adapt to treating process bleed waste streams containing heavy metals. The result of such treatment invariably yields a gypsum-saturated solution containing salts such as alkali metal sulfates, chlorides and fluorides. Presence of anions such as sulfates, chlorides and fluorides in the discharge streams – presently not a major problem- are coming under increasing scrutiny and will have to be addressed in the near future. It is envisaged that discharge limits for sulfate ions will be in place in the near future. Treatment of brackish water to produce drinking water also results in brine streams containing alkali salts that have to be addressed for proper disposal. This paper reviews treatment options for such streams containing high levels of total dissolved solids with emphasis on sulfate removal. Areas covered would be: a) chemical treatment for removal of various constituents that make up the total dissolved solids b) processes for sulfate removal processes –thermal and non-thermal-to recover and reuse of treated water and c) brine use and treatment options.INTRODUCTIONThe rising cost of water and meeting the ever-changing stringent environmental discharge regulations make water recycling and reuse essential. The metallurgical industry has used water as a medium for dissolving and/or rejecting metals and chemicals in addition to removing thermal energy. Any excess process effluent is collected and sent to end-of-pipeline treatment and ultimately discharged to surface water for disposal under a permit. The conventional- and probably the cheapest way -of treating metal-bearing process effluent streams is lime neutralization followed by sulfide polishing for elimination of heavy metals to produce a stream that meets NPDES discharge limits. This results in a stream containing dissolved solids.These dissolved solids normally comprises of inorganic salts. The possible constituents are cations calcium, magnesium, sodium and potassium. The anions are sulfate, chloride, fluoride, nitrate, carbonate and bicarbonate. In addition to these constituents, the treated effluent streams contain very small amounts of heavy metals, oxyanions such as arsenites, arsenates, selenites and selenates. Process streams from gold operations contain residual cyanide. Small amounts of ammonium ions are also present in these streams based on the pH of the solution."

Jan 1, 2012

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By W. J. Wright

Summary This paper describes the general situation of the mining industry in New Brunswick, and gives a detailed description of the recent developments in the antimony deposits at Lake George and the copper deposits in the vicinity of New Horton. At the end are lists of the most interesting geological literature relating to the Province and of the geological and topographic maps that have been published. Introduction In presenting this paper to the Institute, I apologize for the small amount of scientific data which it contains. Recent investigations in the Province of New Brunswick have been carried on largely by outside interests, and at present we ourselves are in the position .of taking stock. However, I am glad of the opportunity of giving you a general idea of the situation. The Province is making an honest effort to learn the truth concerning her mineral deposits and in time hopes to collect data which should be of interest to the mining community.

Jan 1, 1931

By S. Hoskins, S. Chiovelli

"The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd. is in excess of $450 million. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trials where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trials will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work. IntroductionSyncrude Canada Ltd, located in northern Alberta, Canada, operates a mining, extraction, and upgrading facility that removes bitumen from oil sand to produce synthetic crude oil. Oil sand is mined from the orebody using conventional open pit mining techniques. Recently, the mining scheme has changed from a dragline/bucketwheel/conveyor system to a shovel/truck/crusher/hydrotransport operation as depicted in Figure 1. Since the start of production in 1978, the identification, development and application of wear protection has been an ongoing challenge due to the abrasive nature of the oil sands and the massive volumes of materials that are moved. The use of various materials and application processes along with component design modifications has resulted in significant improvements in both productivity and reliability (Adamic et al., 1995; Llewellyn, 1996, 1997; Anderson et al., 1998; Chiovelli et al., 1998).In an effort to continuously improve the operation, Syncrude has been quick to adopt new wear technologies. As seen in Figure 2, since the start of operation, a variety of materials have been used to increase wear performance and ultimately equipment reliability and availability. Although Figure 2 does not show a time axis, the bottom axis may also be used to represent a time progression for the predominate use of these materials at Syncrude. Tungsten carbide metal matrix composite (WC-MMC) overlays are currently the materials of choice for most of Syncrude’s critical production applications. Metal matrix composite overlay technology has potential for significant improvements and Syncrude is actively working with powder consumable manufacturers to advance this technology."

Jan 1, 2004

By W. Pawlak, J. Janiak, C. Rodkiewicz, B. Ignasiak

"There is a general consensus that, in order to widen the utilization of Western Canadian coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques. It is postulated that the concept studied extensively over the last four years at Alberta Research Council (ARC), and based on a combination of hydraulic mining, selective agglomeration with bitumen and/ or heavy oil, pipeline transportation and oil recovery from agglomerates, offers a particularly attractive solution to the problems associated with extraction, beneficiation, transportation and utilization of Western bituminous and subbituminous coals. Results of preliminary experimental work on the feasibility of pipeline agglomeration of metallurgical coal and hydraulic transportation of agglomerates are presented and discussed in the context of conventional agglomeration techniques in stirred tanks. IntroductionAlberta is endowed with enormous reserves of low-sulphur coals which could attract considerable attention of potential customers, but the remote location of this province handicaps its competitiveness on the world market. It is known that Alberta's Cretaceous, particularly metallurgical, coals differ significantly from their Carboniferous counterparts; current R&D work on indigenous coals should continue to expand in order to encourage overseas client s to use these coals more extensively.There is a genera l consensus that, in order to widen the utilization of Western coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques."

Jan 1, 1986

By Peter L. Sheehan, David A. Fawcett, Dennis C. Martin

"Smoky River Coal Limited has successfully completed a major program involving the pattern rock anchoring of a high, steeply dipping footwall slope. The slope dips at approximately 65 to 70 degrees to the north, is benched for the upper 200 feet, is supported with rock anchors for another 240feet, and is unsupported at the pit bottom. In addition to the height and steepness, several structural features including shears, rolls and stratigraphic pinch- outs complicate footwall stability.This paper presents an overview of the project with descriptions of the engineering geology and footwall design, anchor installation, instrumentation and monitoring and a cost summary.IntroductionSmoky River Coal's mines are located in the foothills of the Rocky Mountains near Grande Cache, Alberta, approximately 200 miles west of Edmonton. The Smoky River coal leases were initially developed in the late 1960s and, except for minor shutdowns, have been in continuous operation since 1969 producing a low volatile metallurgical coal, mainly for the export market. Initial coal production was from underground mines; sur face mining started in 1971, and a large surface mine, No.9 Mine, was opened in 1974. Since that time, a number of open pits have been mined within the No.9 Mine area. Surface mining is by conventional shovel-truck method s with the use of a backhoe for mining the narrow pit bottoms.Coal recovery is mainly from the No.4 seam, which has a typical unstructured thickness of 20 feet. The most attractive opportunities for open-pit mining exist in areas of over thickening of the coal seam in the hinge zones of synclines and anticlines and in dip-slope situations. The mining of the more structurally complex pits and steeply-dipping footwall slopes requires that consideration be given to footwall stability."

Jan 1, 1988

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By Michael G. Nelson

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modelling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing, allowing optimization of the mill processes on an almost realtime basis. This is not happening because mill feed it is often treated as a uniform material, when in reality it varies in composition and characteristics. The University of Utah is investigating the use of odor sensors for maintaining traceability in ore production and processing. Odor sensors now used in food processing, environmental monitoring, and other applications can detect the presence of very small amounts (0.1 - 500 ppm) of some molecules. An assortment of such molecules could be used to ?tag? blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ?electronic noses? could be used to assess its characteristics in real time.

May 1, 2004

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By P. Scinto, A. Festa

"Orway Mineral Consultants Ltd (OMC) as a consultancy has specialized in comminution circuit design for over 30 years. The OMC Power Model is OMC’s in-house software for specific grinding energy power-based circuit calculations. The model uses ore hardness parameters from testwork, circuit configuration, equipment geometry and operating conditions as inputs. The model combines proprietary and published power models to predict the total specific energy and the specific energy for each of the components of the comminution circuit. This makes the software a valuable tool for the design and validation of JKSimMet modelling or actual plant performance. Proprietary calculations have been developed and reconciled with over 100 plant benchmark projects encompassing a variety of comminution circuit configurations.This paper describes the OMC approach for determining power requirements for the design of grinding circuits. The accuracy of the OMC Power Model software is confirmed through plant survey benchmark performance and comparisons are made with other power modelling techniques. Practical examples are presented, showing applications for single stage SAG (SS-SAG), SAB and SABC circuit configurations.IntroductionConventional low throughput grinding options, consisting of multi-stage crushing followed by rod and ball mills, have almost become obsolete in the move to higher milling rates required to process lower metal grades. Grinding circuits with fully autogenous (AG) or semi-autogenous (SAG) mills, often combined with ball mills are now the standard to meet the high capacity requirement for processing ores with lower metal grades. Simulation software and power-based equation methodologies have been established for designing AG/SAG based grinding circuits and predicting their energy requirements.Presently, power-based equations remain the principal method for designers to size mills and estimate the power requirement for comminution circuits. The technique is simple and it relies on the design to specify a feed and product size plus a hardness index to produce a specific energy value (kWh/t). The desired throughput of the mill is multiplied by the specific energy to give the mill power requirement, which is used in turn to size a mill for dimensions, internal geometry and loading conditions to match the power draw."

Jan 1, 2015