Search Documents

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By P. J. Morgan, E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising’s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Yan Germain, Université Laval, Bernard Dallaire, Jocelyn Bouchard, Peter Radziszewski, Gilles LeBlanc, Michelle Levesque, Nicolas Tremblay

"The comminution process is estimated to be only 1% efficient, resulting in waste energy dissipated as heat, noise, and vibration. Energy recovery from grinding circuits has not been implemented mainly because recovering heat from the surface of the grinding mill or from mill slurry can impede operation, increase maintenance requirements, and prolong plant shutdown time (and production). However, currently very little information is available in the public domain regarding the amount of waste energy and that potentially recoverable in the grinding circuit of a mineral processing plant. Availability of such information could drive innovation and improve decision-making regarding opportunities for waste energy recovery. The Canadian Mining Innovation Council (CMIC) has initiated a study with CanmetMINING and mining industry partners to develop a model to map the energy flows in grinding circuits and to quantify the potential for energy recovery. The paper outlines the underlying fundamentals and data requirements for use in the model and then focuses on quantifying the energy recovery potential of the semi-autogenous grinding and ball mill circuits at the Agnico Eagle Goldex Division. Results show that most of the electrical energy (over 75%) is used to heat the slurry, leaving only a relatively small amount of it to achieve mechanical work (~9%). INTRODUCTIONCanmetMINING commissioned a study in 2013 to better understand the barriers for adoption of new technologies in the mining industry (MNP, 2013). The conclusions highlighted the importance of enhancing industry/regulator engagement and communication to raise awareness and improve the industry’s comfort level with new technologies.In November 2014, the Green Mining Innovation Advisory Committee (GMIAC) held a workshop to explore the possibility of accelerating the uptake of green mining technologies by bringing together key stakeholders among the mining value chain to address industry priorities. Participants included representatives from mining companies and associations, academia, provincial governments and federal departments and organizations. Two key priority areas emerged at the workshop: i) energy saving, and ii) water management."

Jan 1, 2016

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By Kazutoshi Haga, Ariunbolor Narankhuu, Ariuntuya Battsengel, Yasushi Watanabe, Altansukh Batnasan, Akita University

"Rare earth minerals are usually concentrated by flotation, magnetic or gravity separation methods to produce concentrates that are subsequently leached with hydrochloric (HCl), sulfuric acid (H2SO4) or nitric acid (HNO3). About 75 % REEs are lost in gypsum by-product when apatite is dissolved in H2SO4, whereas more than 80% of REE can be extracted from the apatite using HCl and HNO3 leaching processes, respectively. Therefore, the main aim of this study was to find an efficient process of dissolution of rare earth elements (REEs) from apatite ore by sulfuric acid solution due to its lower cost. In order to optimize the dissolution process, effects of different parameters, namely, concentration of H2SO4 (0.05 – 6 M), solid/liquid phase ratio (1:50 – 1:100), temperature (20 – 80 ºC), agitation speed (300 – 900 rpm), and leaching time (0.5 - 6 h) on the dissolution of REEs from apatite ore were examined in various intervals. The contents of main REEs in the apatite ore used in this study were (as % wt): 3 % La, 6 % Ce, 0.6 % Pr, 2.1 % Nd, 0.2 % Sm and 0.3 % Y. X-ray diffraction (XRD) analysis identified fluorapatite and phlogopite as main minerals in the ore. The results obtained from leaching experiments showed that more than 85% of REEs were dissolved from the apatite ore under the optimized conditions, which were: 1 M H2SO4, particle size of -150 + 100 µm, S:L phase ratio of 1:50, agitation speed of 500 rpm at 20 ºC for 1h. The XRD analysis revealed that main mineral compositions of the residues from 1M and 6 M H2SO4 leaching are gypsum (CaSO42H2O) and hemigypsum (CaSO40.5H2O), respectively.INTRODUCTIONThe term rare earth elements (REEs) denote the group of 17 chemically similar metallic elements consisting of the 15 lanthanides, plus yttrium (Y) and scandium (Sc) in the periodic table. These metallic elements are generally divided into two sub-groups; (1) the cerium sub-group, which is called “light rare earth elements” (LREEs), includes the elements from lanthanum (La) to europium (Eu), and (2) the yttrium (Y) sub-group elements, which are known as “heavy rare earth elements” (HREEs), are the remaining lanthanides from gadolinium (Gd) to lutetium (Lu) plus yttrium (Gupta and Krishnamurthy, 2005). The REEs occur together in the minerals due to their chemical and physical similarities, which cause problems of separating them from one another (Abreu and Morais, 2014). Although REEs are relatively abundant in the earth’s crust, they are typically dispersed and rarely occur in concentrated forms, making them economically challenging to obtain. There are a wide variety of rare earth minerals, however economic deposits of REEs in mining are bastnasite (La, Ce) FCO3, monazite (Ce, La, Y, Th) PO4, and xenotime YPO4 (Binnemans, 2013; Xie, et al, 2014). Due to the unique physical, chemical, catalytic, electrical, magnetic and optical properties of REEs, demand of these elements has increased dramatically with the advent of new technologies in electronics, communication, construction, energy and medicine (Jordens, et al, 2013). Since 1990, China has provided about 90 % of REEs worldwide. Japan and United States are the largest consumers of China’s REEs. In 2010, China announced to reduce REEs exports to Japan, as it tended to increase prices of REEs and to reduce a stable supply of REEs in the world market (Humphries, 2013). Therefore, there has been an increase in recent exploration activities intended to reveal new commercial sources of REEs and to bring them into production (Antico, et al, 1996). Apatite is an important host mineral for REEs in igneous and metamorphic rocks and can be used as an ore for those metals (Kanazawa and Kamitani, 2006). Apatite is also the main source of phosphate fertilizers and phosphoric acid (Habashi, 2013; Emsbo, 2015)."

Jan 1, 2016

By V. S. Gischig, G. Preisig

Hydraulic stimulation of deep reservoirs is an essential procedure for developing engineered/enhanced geothermal systems (EGS), but also in other Geo-energy contexts. The goal is enhancing permeability to such a degree that fluid flow rates within the reservoir are sufficiently high for an economically productive reservoir. Two fracture stimulation mechanisms are distinguished that may occur concurrently during the hydraulic treatment: 1) During hydro-fracturing (HF) new tensile fractures are propagated from the borehole by means of a fluid pressure overcoming the minimal principle stress d3 plus the tensile strength T0 of intact rock. In case of a pre-existing fracture oriented normal to d 3 , the fracture can be opened by exceeding d 3 only. Fluid injection is performed via small packed intervals for creating a stack of hydraulic fractures. 2) During hydro-shearing (HS), over-pressure induces slip along pre-existing fractures that are favourably oriented in the stress field for reactivation in shear. Such stimulation is usually performed in a large packed interval or in an open borehole. Which mechanism occurs predominantly during stimulation depends on the rock mass structure and in-situ stress field, but also on the orientation of discontinuities intersecting the open-hole section and thus being pressurized. Both mechanisms also differ in how they affect fracture permeability. While permeability gained by HS is mostly irreversible due to rearrangement of asperity contacts accompanied with shear dilation, permeability enhanced during HF reduces nearly reversible after pressurization unless proppant is used to ensure permanent apertures. In this contribution, we critically discuss the pros and cons of both mechanisms regarding efficiency of enhancing permeability and the associated hazard of induced earthquakes based on literature review and numerical modelling. We review literature that reports on how much permeability required for productive EGS reservoirs and how much permanent permeability can be gained by stimulation. We also compile information regarding the degree of seismicity induced during HFor HS-dominated stimulation procedures, together with conceptual studies that reveal characteristics of seismicity associated with the two mechanisms. Many observations and models indicate that HF may have a higher tendency of being aseismic, while felt seismic events are usually associated with HS. Further, we present a hydro-mechanically coupled fracture flow model that investigates, if and to what degree the stimulation strategy can be designed such that one of the two mechanisms is evoked and dominates over the other. It shows that HS may dominate in presence of larger persistent fractures nearly optimallyoriented in the stress field, even if HF is attempted in short packed intervals. The model further demonstrates that stress transfer during HS promotes the development of permeability across an anisotropic layer of the stimulated rock instead of a large volume. Hence, the study sheds light onto the feasibility of creating productive EGS reservoirs in crystalline rock at several kilometres depths.

Jan 1, 2015

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Mehmet F. Taner

"The East Sullivan Stock (ESS) is a small, composite felsic alkaline pluton of presumedlate Archean age in the Val d’Or mining district. Three main facies have been distinguished: mon-zonite sensu stricto, porphyritic monzonite, and green trachytic porphyry. This monzonitic group ofrocks is of relatively homogeneous composition with high abundances of Na2O, K2O, Ba, Sr, Rb, Zr,Mo and LREE. The alkaline ESS is distinguished from other igneous units in the Val d’Or miningdistrict, such as the Bourlamaque Batholith, by relatively high concentrations of Ba, Sr, Rb, Mo, Cuand Au. The ESS hosts many base (Cu, Mo) and precious (Au) metal occurrences, including: (1)porphyry style Cu-Au-Mo disseminated sulfde deposits, (2) Cu-Au deposits in volcanic rocks near the ESS contact, and (3) pyritic gold mineralization in east-west trending shear zones. The ESS is well defined by concentrical zoning on the aeromagnetic vertical gradient color map, and displays four linear trends, which are assumed to be structural lineaments, at 035°-055°, 320°-300°, east-west, and north-south. The main mineral occurrences related to the stock display a preferred spatial association with the east-west linear magnetic trends.The ESS is preferentially located along a major structure and was emplaced late in the evolutionof the Abitibi subprovince like other felsic alkaline plutons. This stock is similar to late-tectonic min-eralized felsic alkaline intrusions of the Kirkland Lake and Larder Lake mining districts in Ontario, and to the Allard stock in the U.S.A. which is associated with gold and base metal mineralization. Similarities also exist with younger alkaline plutons associated with Cu-Mo-Au porphyry deposits in the Canadian Cordillera, which formed in tensional tectonic environments. The felsic alkaline magmamay have formed by partial melting of deeply buried supracrustal rocks, concomitant with the development of deep fractures such as the Cadillac Fault. In such an environment, hydrothermal solutions carrying remobilized metals from deep supracrustal rocks may have deposited gold and base metals in structural traps. Plutons similar to the ESS should be good targets for mineral exploration. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum."

Jan 1, 1996

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By H. Y. Sun, Q. Y. Tan, X. P. Niu, L. Li, Y. Jia, R. M. Ruan

During bioleaching processes of sulfide minerals, the sulfide minerals act as the natural habitats for acidophiles, of which, most are autotrophic iron and sulfur oxidizing microbes. These microbes acquire energy by oxidation of sulfide minerals, and play crucial role in bioleaching processes. In the industrial bioleaching heaps, microbial community and their activity are highly related to engineering configurations, while the optimized industrial operation can help to fast dissolution of aim minerals and acid/iron balance under optimized microbial condition. Microbial community succession and activity formation, the function of microbes to mineral dissolution, the mechanisms to promotion and inhibition of sulfide minerals oxidation, and the industrial instances for microbial community regulation were reviewed. For these instances, promoted microbial activity helped to fast pyrite oxidation for sulfuric acid generation, which realized zero sulfur acid addition to the irrigation solution in the initiation of a bioleaching heaps. High microbial activity by optimized operation parameters improved Cu leaching efficiency during the heap bioleaching process. And also by inhibition of microbial activity, especially the iron oxidizing microbes, the excessive pyrite oxidation can be inhibited, which helped to the acid/iron balance during heap bioleaching. INTRODUCTION Around the world, high grade copper ore are exploited, while barely new high-grade deposits are succeeded, the copper grade of ore deposit is constantly decreasing. The increasing copper demands worldwide requests to process these low-grade ore deposits. Processing of low-grade ores are not economical by usual extraction processes. Heap leaching is a cheaper process for recovery of low-grade ores, and has been applied to extract valuable metals from sulfide minerals worldwide, such as copper, gold, uranium and nickel (Gericke et al., 2009). Heap leaching process has greatly decreased the economic grade and expanded the recoverable ore reserve worldwide (Brierley, 2008). It is usually carried out in the open environments, and could process huge amount of ore (usually in millions of tonnes in one reactor) in the heap reactor (Gericke et al., 2009). For copper sulfide, especially the secondary copper sulfides, heap (dump) bioleaching is successfully applied. Heap bioleaching process is cost saving, and sometimes can be achieved without adding chemical into heaps, by microbial fixing of the atmospheric N2 and CO2, and generating oxidant Fe3+ and sulfuric acid in heaps from oxidation of sulfide minerals. Also heap bioleaching is environment friendly by cycling use of the leaching solution, and without exhaust emission.

Jan 1, 2019

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005