Search Documents

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932

By K. C. Marsden, B. Pesic

"Interest in the efficient production and recycling of rare earth elements has increased in recent years along with the prices of these elements. The molten LiCl-KCl eutectic is one ionic solvent which can be utilized for these purposes. The LiCl-KCl eutectic has also been selected as the electrolyte for focused research for advanced pyrochemical recycling processes for used nuclear fuel in several nations. Rare earth elements are fission products with notable neutron absorption characteristics, and thorough understanding of the properties and behavior of these elements is critical to their successful partition from the electrochemically-similar actinide elements. The number of research papers investigating individual rare earth elements has greatly expanded in the approximately 35 years since the last review. These research papers are presented in a variety of languages and technical formats, making data difficult to compare, and are sometimes contradictory. A review and summary of diffusion properties of rare earths in LiCl-KCl eutectic was performed, and the data translated to a common format for evaluation. INTRODUCTIONThe rare earth elements have experienced growing importance in recent decades due to their application in high technology, including optical lenses, lasers, high-temperature superconductors, improved alloys, high energy-density batteries, and powerful magnets for compact electronic devices. Their historic production methods and uses are detailed in several texts (Hampel 1971; Bautista &Jackson 1992; Gupta & Krishnamurthy 2005). A s the p rice o f these e lements has r isen in r ecent years, so has interest in their efficient production and possible recycling options. Rare earth oxides are concentrated through hydrometallurgical techniques, but the high thermochemical stability of their oxides precludes production of rare earth metals in aqueous systems. However, the wide electrochemical window and better control of pO2- in fused salt systems allows the production of these reactive metals from their halides or oxides. The high ionic conductivity and diffusivity of the molten ionic electrolyte allow high currents with limited resistive losses (Fray 1980). Electrolytic methods in fused salts are commonly adopted for the production of bulk rare earths in a variety of molten salt systems. Fluorides are sometimes proposed for oxide electrowinning processes due to ability to dissolve the rare earth oxide, reduced hygroscopic behavior, and the wider electrochemical separation between O2 and halide gas evolution (Mohan Das, Damodaran et al. 1988; Gibilaro, Pivato et al. 2011). However, in most electrolytic production processes, such as that for mischmetal, the rare earth oxides are converted to chloride prior to electrolysis in a chloride bath (Gschneidner Jr. & Eyring 1978; Sharma 1987). Of the chlorides, the LiCl-KCl eutectic is one specific medium in which metal production and production-related investigations have been conducted (Gschneidner J r. & Eyring 1978; Driscoll & Fray 1993). L iCl-KCl eutectic has the advantages o f h igh conductivity, but relatively low viscosity and operating temperature. The low operating temperature allows simpler design, with reduced energy consumption, salt volatility and cell corrosion."

Jan 1, 2012

By Sazol Das, Hany Ahmed, Ganesh Bhaskaran, Zhuoru Wu

"Friction stir welding (FSW) process in lap configuration for dissimilar materials has been developed and tested for steel to aluminum joining. A novel cylindrical tool was designed for improved material flow. The joining of steel to high strength 5xxx and 6xxx aluminum was carried out by FSW technique using optimized process parameters. The microstructure, micro-hardness, joint strength and corrosion properties at the weld interface have been investigated. Optical and scanning electron microscopy reveled a well layered structure at the interface and lap shear tests of the welds showed excellent fracture resistance. Neutral salt spray tests for up to 500 hours (ASTM B117) were carried out on the bare steel to aluminum FSW joints, which did not show neither evidence of corrosion at the weld interface, nor any degradation of the weld strength. The FSW lap configuration was applied to prototype commercial vehicle structural component whereby a steel stiffener insert was friction stir welded to high strength 6xxx aluminum alloy. The interface microstructure showed layered root without any steel shattering in aluminum side. A finite element study was carried out to quantify the benefits where it was found that the stiffness increases by 76% under bending loads and 36% in torsion loads.INTRODUCTION Energy preservation and environmental issues, namely carbon footprint and legislation around emission in transportation industries has led to a growing need to use of lightweight materials such as aluminum and magnesium alloys along with various grades of steel in structural application, while still maintaining their strength and crashworthiness. Assembling dissimilar materials within integrated structure is thus a stringent requirement related to optimum performance. In order to achieve an efficient technology of joining dissimilar materials such as aluminum to steel, it remains difficult to select an effective welding process for a given joint configuration. The use of aluminum in transportation industries for structural component is not exclusive in a design and is almost always used along with various steel grades for a mixed materials solution, thus dissimilar aluminum/steel lap joining is of great interest since this is widely used in the assembly of parts (e.g. pillar, frame rails, chassis, body in white (BIW), CAB, etc.)."

Jan 1, 2018

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ?Mine to mill? strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

"The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle.When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice. INTRODUCTIONThere are a lot of joints and fractures in surrounding rock mass of deep-lying in the Jinping-II hydropower station, which has a great influence on the physical and mechanical properties of rocks and effects the acoustic wave propagation and attenuation law in rock. Many previous research and project examples has proved that sound propagation parameters are closely related to crack and stress condition. Thus, it has certain theoretical significance and practical application value to carry out researches on sound propagation characteristics and establish damage constitutive model of fractured rock mass which is related to sound propagation parameters."

Jan 1, 2015

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By Bruno Bussière

Acid Mine Drainage (AMD) from mine wastes is one of the most environmental challenge currently facing the mining industry. AMD is the result of the natural oxidation of sulphides exposed to air and water. When mining wastes have the potential to produce AMD, these reactive wastes have to be managed to meet existing environmental regulations. The LTA site (property of Barrick Gold Corp.) contains sulphide tailings that have the potential to generate AMD. The closure option Barrick selected was to construct a multilayered cover with capillary barrier effects (CCBE). The main objective of this CCBE is to prevent the production of Acid Mine Drainage (AMD) from the tailings stack covering an area of approximately 60 ha. Since its construction in 1996, the cover has been monitored to evaluate its performance. Two of the measured parameters are volumetric water content and matrix suction. This paper presents some of the main results from the monitoring program that started seven years ago. The results show that the cover is largely able to maintain a high degree of saturation (greater than 85%) in the moisture-retaining layer. The actual performance of the CCBE on the flat surface of the 60 ha site is even better than expected at the design stage. The area that requires more specific attention with the LTA cover is the influence of slopes that can reduce the performance of the CCBE during dry periods. However, these effects seems to be local and do not significantly affect the overall performance of the CCBE to mitigate the production of AMD at the LTA site.

May 1, 2003

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda's ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946