Search Documents

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By W A. James

The use of spectrographic semi-quantitative analysis has recently been of considerable value in establishing the geological relationships in a complicated orebody. The principal minerals found in the Mount Pleasant orebody are cassiterite, stannite, sphalerite, molybdenite, wolframite, chalcopyrite and galena, associated with arsenopyrite, pyrite and fluorite. In addition to the large number of minerals, a further com-plication is the non-uniform distribution of the economic minerals, with one mineral being the only one present in major amounts in one area and another mineral being predominant in another area. At the same time, all minerals are present to a minor extent throughout the deposit. This heterogeneity made it advisable to analyse all exploration samples thoroughly. Analysis by conventional means would have resulted in prohibitive costs. By the use of emission spectroscopy, however, it was possible to obtain, quickly and relatively inexpensively, a reasonably comprehensive picture of the orebody un-der investigation.

Jan 1, 1963

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By Michael T. G. Brown

Syncrude Canada Ltd. has recently completed construction of its ambitious tar-sand mining and processing facilities at Mildred Lake, Alberta. The Syncrude site is approximately 48 km (30 miles) north of Fort McMurray near the west shore of the Athabasca River. The Syncrude operation involves the open-pit mining of approximately 270,000 tonnes (300,000 tons) of tar sand daily using draglines and a conveyor system. Bitumen is extracted from the tar sand, upgraded to oil-gas and transported to refineries in Edmonton and other locations for final processing . The Beaver Creek Dam forms part of the mining facilities for the Syncrude tar-sand mining operation. Water from Beaver Creek is diverted from the open-pit mine site south to the Athabasca River via Ruth Lake and the Poplar Creek Dam. General site layout is shown on Figure I . Design of the dam was completed by R. M. Hardy and Associates Ltd. of Edmonton, Alberta (now Hardy Associates (1978) Ltd) . Construction was undertaken during the summers of 1974 and 1975 under the direction of Canadian Bechtel Limited, managing contractors for Syncrude Canada Ltd. Total length of the dam is approximately 2.8 km (1.7 miles), with a maximum height in the order of 16 m (50 ft) The Beaver Creek Dam is located in a broad, flat, poorly drained valley. About 50 per cent of the site is covered with treeless peat deposits, which ranged in thickness from in excess of 5 m (15 ft) at the east end of the dam to less than 1 m (3 ft) at the central portion. The peat deposits overlie Pleistocene meltwater sediments on top of clay/clay shales of the Clearwater Formation and the tar sands of the McMurray Formation. The peat deposits and high groundwater levels at the site combine to make the excavation and construction of a conventional rolled clay cutoff impractical. For these reasons, the slurry cutoff trench technique was utilized to produce an efficient and effective seepage cutoff under various sections of the Beaver Creek Dam .

Jan 1, 1979

By Robert Boutilier

For more information on what the social licence means, see the following: Joyce, S. and Thomson, I. 2000. Earning a social licence to operate: Social acceptability and resource development in Latin America. The Canadian Mining and Metallurgical Bulletin, 93(1037) Nelson, J. and Scoble, M. 2006. Social License to Operate: Issues of Situational Analysis and Process. Vancouver, BC: Department of Mining Engineering, University of British Colombia. Thomson, I. and Boutilier, R.G. 2010. The Social License to Operate In P.Darling, (Ed.), SME Mining Engineering Handbook: Littleton, CO: Society for Mining, Metallurgy and Exploration. Much of what has been written and said about the social license to operate focuses on what the company has to do or not do. But the social license is a two-sided relationship. We also need to look at what the community has to do, or not do, in order to be capable of issuing a social license that is meaningful.

May 1, 2010

By J. H. Fulton

Summary Considerable test work has been done with the detachable type of carbide bit. In general, these bits improved drilling operations, but at a bit cost .greater than was compensated for by the reduction in man-hours of labour. Too few bits continued in service for the possible drilling life of the carbide inserts, and technical improvements or lowered first cost, preferably .both, are indicated ?in order that the bits can be generally acceptable as an economical drilling tool. In ?preliminary test work, the drill rods .with ?one insert of the chisel-bit type appear to be more trouble-free, to have a longer life, and to give a somewhat lower bit cost per foot drilled, than other types. INTRODUCTION The object of this paper is to outline briefly the 'methods used and the results obtained in test work with tungsten carbide bits used in combination with the smaller bore, lighter weight rock drills. As various articles have appeared in the past few years giving the historical background ?and early development of carbide ?bits, this information will not be repeated. Table I lists the equipment used in the test work. The stopers weigh about 95 pounds and the jackhammers with airleg from 97 to 110pounds. The smaller rock drills are stated to deliver about 2,200 blows per minute at 1 to 30 rotation and to require 85 to 95 cubic feet of air at around 100 pounds pressure.

Jan 1, 1950

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation's entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By L. L. Bolton

The Department of Mines as at present constituted has evolved from the organization which came into existence following the passage of the Geology and Mines Act by the Dominion Parliament in 1907. At the outset, it may be said that it is not a function of the Department of Mines, nor of any of its branches, to administer the mining rights vested in the Crown. The title to Crown lands in the provinces of Nova Scotia, Prince Edward Island, New Brunswick, Quebec, Ontario, and British Columbia ( with the exception of certain specified areas, such as Indian Reserves, Ordnance Lands, the Railway Belt of British Columbia, and the Peace River Black) is vested in the respective provincial governments ; the title to Crown Lands in the provinces of Manitoba, Saskatchewan, and Alberta, the Yukon and Northwest Territories, and in the Canadian Arctic, is vested in the Dominion Government, and matters pertaining thereto are (with a few exceptions) administered by the Department of the Interior, Ottawa. Nor are statistics of mineral production at present collected and published by the Department of Mines. This function did belong to the Geological Survey from 1886 to 1906, and to the Mines Branch from 1907 to 1920; but commencing with 192l this duty was transferred to the Dominion Bureau of Statistics, consequent upon the decision of Government to place the collection of all statistics under the direction of one officer.

Jan 1, 1929

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By G. G. W. Thom, A. A. F. Schuldt

At The Steel Company of Canada, Limited, iron oxide dust from the basic oxygen open hearths is being collected by means of electrostatic precipitators. The utilization of this dust, which has been hampered by the presence of zinc and lead oxides and sulphur compounds, is made possible by direct reduction in a rotary kiln. The description of the dust collection system and the results of kiln tests are presented.

Jan 1, 1966