Search Documents

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By Z. D. Hora

The major fluorite producer in British Columbia was the Rock Candy Mine, inactive since 1942. Other deposits of economic interest include the Rexspar deposit, in which fluorite is associated with uranium and rare earth mineralization, and the Eaglet and Liard River occurrences. THE former Rock Candy fluorite mine, located 26 km north of Grand Forks, is the only major past producer of fluorite in British Columbia. The deposit was in production from 1918 to 1929 and again in 1942; total output was about 36,000 tonnes with average grade between 22 and 32 per cent CaF2. The fluorite body occupies a steeply-dipping vein structure, approximately 175 m long and up to 12 m wide, in porphyritic syenite. The chief vein-filling minerals are quartz and fluorite with local small len ses of barite. Fluorite content decreases with depth and the deposit becomes silicified. The Rexspar (or Birch Island) fluorite deposit is located 130 km north of Kamloops. The deposit is complex with rare earth elements and high uranium values, but !1uorite mineralization forms an independent zone adjacent to the uranium orebodies. Fluorite is present as fine-grained impregnations and as breccia cement in strongly schistose or brecciated alkali feld spar porphyry. Reported reserves are 1,088,000 tonnes of 22 per cent CaF2 or 450,000 tonnes of 29 per cent CaF2. 268 Another potential deposit of fluorite is Eaglet, situated on the north side of Quesnel Lake. Fluorite occurs as a stock work with scattered veins and irregular lenses up to 20 centimetres wide and as impregnations in altered Proterozoic Kaza Group feld spathic gneiss over an area of 1,500 metres by 500 metres. To date (1983) approximately $2 million have been spent on the exploration of this property and reserves of 18.8 mimon tonnes grading 11.59 per cent CaF2 have been outlined . A group of significant occurrences is known from north of Liard River Hot Springs Park , where fluorite occurs in small zones up to 17 m thick along the interface between Middle Devonian Dunedin Formation limestone and Middle Devonian to Mississippian Besa River Formation argillite. Fluorite, associated with witherite, barytocalcite and barite, is present as replacement bodies, breccia fillings and minor veins.

Jan 1, 1984

By H. R. Butler, R. N. Browne

"The International Nickel Company of Canada Limited consumes some 33 ½ millions of gallons of fresh water and reuses more than 100 millions of gallons of water daily. The continuing search for suitable recycle methodology has enabled the Company to put one 25,000 TPD mill on line utilizing recycled water entirely and a second 35,000 TPD mill is under construction which will likewise employ the concept of recycled water. Future milling plans are aimed at the replacement of all fresh water with recycled water, including sewage effluent and mine waste water.WATER REUSE AT INCO’s SUDBURY MILLSAs man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive -- W A T E R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the United States was over 300 billion GPD (l) or more than 1,700 GPD per person(5) The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the United States by the year 2000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then can we continue to wreak such havoc on that life-sustaining substance - WATER?"

Jan 1, 1970

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

By K. D. Hester

This paper will review the metallurgical aspects of the completed expansion program at Quirke, and the current rehabilitation and refurbishing program at Panel. During the Quirke program, completed at the end of 1977, the plant capacity was increased from a nominal 4,500 to 7,000 short tons per milling day. The expansion of crushing, grinding, neutral thickening and filtering, leaching, partial neutralization, sand-slime separation, sand washing, C.C.D., clarification, ion exchange, mine water treatment, and tailings neutralization and pumping will be considered. The application of Enviro-Clear thickeners in the mine water treatment circuit and in the C.C.D. will be briefly reviewed. An automatic grinding and classification circuit for limestone will also be covered. The refurbishing program underway at Panel will be discussed. The Quirke and Panel plants will be contrasted and compared. In particular, reference will be made to environmental considerations. The innovative system for producing yellow cake at Panel, LAMIX, will be considered as well as the proposed treatment system for Panel tailings.

Jan 1, 1979

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011

By A. del Campo A.

The roast segregation process, which was patented in 1974, makes use of a set of chemical reactions that are different from the traditional sequential oxidation of iron and copper sulfides used by all modem pyrometallurgical processes to treat copper concentrates. It allows metallic copper to be obtained via sublimation of copper chloride at temperatures in the range of 700-800 OC. In addition it avoids melting the concentrate, doesn't require transferring molten materials, doesn't need flux addition and allows nearly all of the sulphur to be removed in one stage as a high-S02 gas stream. Most importantly, it allows a decrease in the use of energy to approximately 6 million BTU/ton of anodes. This represents a saving of approximately 40%, compared to the potential of the most advanced processes presently used. Such a promising process has been waiting for its first industrial application for more than 30 years. This article examines the technical difficulties that have delayed application of the roast segregation process to beneficiate copper concentrates. Special emphasis is made on material handling aspects, discussing the possibility of using a well designed mass flow silo as the main processing vessel to carry out the segregation stage. Cu2007

Jan 1, 2007

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By G. G. Bowser

Introduction Flame shots are of very infrequent occurrence in the coal mines of Nova Scotia. Probably not more than one is recorded in three months. Many shot-firers have never experienced one, and many never will. As a consequence, although all such occurrences are very carefully investigated, information concerning the cause of flame shots is somewhat meagre. In the course of the years, however, something has been learned of the practices and conditions that are responsible for them. During the past ten? years, over seventeen million shots were fired in the coal mines of Nova Scotia and only fifty-two faulty shots were reported or investigated during that time. In thirty-nine of these, flames were reported; in five, sparks only; and in eight, smoke only. In eight of these occurrences, unburned explosive was found after firing. In one of these eight, flame was seen in the back part of the hole, and an accompanying hissing sound pointed to burning explosive. In four of them, there was no evidence that gas was not ignited. All samples of explosives from these faulty shots which were submitted for analysis were found to be normal, except two, in 1937, which contained excessive moisture. These two samples were from two following shots in the same room on the same day. The initial cause of trouble with all eight shots was one or several of the following: explosives in poor condition, separation of cartridges, incorrect priming, shot hole in poor condition or not properly cleaned. In the case of sixteen or seventeen of the thirty-nine shots which flamed, data are insufficient for conclusions to be drawn as to the cause of the flame.

Jan 1, 1947

By F. Dubuc

"The Adams Mine of Jones & Laughlin Steel Corporation is situated on the Boston Township iron range near Kirkland Lake, Ontario. Eight different orebodies have been outlined, with a total open-pit crude tonnage of. about 100,000,000 tons or the equivalent of 30,000,000 tons of concentrate. The ore consists of fine-grained, well-bedded Early Precambrian iron-formation composed essentially of alternating layers of chert and magnetite. Grade averages about 22 per cent magnetic Fe.The iron range varies in width from 3,000 to 4,000 feet and is made up of several horizons of iron-formation, cherty ""quartzite"" and volcanic rocks. The latter consist mostly of basic lava flows and minor amounts of tuff. Dips are rarely Jess than 50 degrees, and the range is believed to represent an overturned limb of a major synclinal structure. Dykes of syenite and lam prophyre, along with local younger diabase, intrude the rocks of the iron range."

Jan 1, 1966

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015