Search Documents

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

Production implications of the introduct- ion of electric L.H.D. units in sublevel open stoping and pillar recovery at Rosebery are covered by Faulkner (1982) and Carlton (1982). The following engineering aspects associated with the decision to introduce electric L.H.D.'s are considered here: - Initial requirements for commissioning, including power reticulation at an adequate level to all operating areas. - Conversion of a manual system to radio remote control. - Maintenance backup requirement to ensure that the production potential is realised.

Jan 1, 1982

By Bedford D. J

The post pillar cut and fill stoping method has been adopted by King Island Scheelite for the extraction of the main Dolphin orebody. The orebody is a massive, tabular deposit varying from 10 to 50 metres in thickness, and dipping at approximately 30¦ towards and under the sea bed. The mining method was selected for 1. maintenance of hangingwall support under the sea bed; 2. maximisation of first stage ore extraction; 3. flexibility of mining, allowing maintenance of grade and selective mining around waste bands within the orebody, and 4. compatibility of existing equipment both with stoping and the on-going underground mine development programme. Stope parameters were established on the basis of initial rock stress analyses, and since the undercut phase of mining the stoping programme has been monitored with various types of deformation measuring devices installed in a series of large diameter boreholes.

Jan 1, 1977

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Stewart A. M, Price D

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings are based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations.

Jan 1, 1992

By F Faraj, M Pal, M Haest, M Bradshaw, H Lang, K Hume

MineSense Technologies Ltd. is revolutionising grade control at mining operations by installing ShovelSense® sensors on buckets that measure the grade of every load before it is dumped in the truck. This allows the mine to exploit grade variations at a resolution that was not available before, reducing the amount of ore loss to the waste stream and removing waste from material destined for processing. These changes dramatically improve the profitability and sustainability of mining operations. ShovelSense relies on X-ray fluorescence analysis of the rocks as they flow in the bucket and is integrated with fleet management to direct the trucks to the right destination. Lab simulations of ShovelSense measurements on porphyry copper ores show correlations between predictions and lab measurements at 0.98 r-squared with a coefficient of variation of 10 per cent. Visualisation of copper grade predictions in three dimensions shows a reasonable match with the dig plan, but with local changes in the ore-waste contact due to more accurate contact identification, related to blast movement and other mining factors. Correct delineation of these contacts ensures ore trucks are not sent to the waste dump and waste trucks are diverted from the crusher, creating enormous value for the operation and the environment.

Mar 22, 2022

To the layman or the casual in- vestor, the critical problems in the mining industry appear to rest on the questions of finding and developing an orebody. The high cost of finding a major orebody suggests that the search is the only matter of real concern. However, the resulting operations which hopefully will provide a profit- able return, depend very heavily on the quality of the servicing that the particular industry receives. Once the mining venture has been established with the necessary plant, equipment and infrastructure, the routine servicing becomes an important function of the operations.

Jan 1, 1975

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

By Christie AB, Bull VH

The geological environments of gold deposits are reviewed in relation to the strong resurgence in exploration for gold since 1979. The resurgence is due mainly to New Zealand's geological endowment with gold and its history as a gold producer. Major past production was from Cenozoic placers of Otago and Westland, late Cenozoic epithermal deposits of the Hauraki Goldfield, and the respective Paleozoic and Mesozoic lode deposits of the Reefton and Otago Goldfields. These same geological environments are the targets of current exploration, mainly in extensions of previously mined deposits. On the Westland and Otago Goldfields alluvial and fluvioglacial gravel placers, mainly representing lateral and depth extensions of previously worked ground, are being mined and prospected. Gold production in 1984 was exclusively from these deposits, and the development of mobile concentration plants has resulted in a great increase in mining activity. Mineralised zones adjacent to previously mined lodes in the Hauraki Goldfield, Reefton Goldfield, and at Macraes Flat (Otago Goldfield) are being intensively explored. At Waihi (Hauraki), an open-pittable resource of about 10 million tonnes of ore has recently been delineated. Some new deposit types and little explored environments are also receiving attention. They include: gold-sulphide quartz veins hosted in an alkaline granite dike in west Nelson; hot spring type gold deposits in fossil geothermal (epithermal) systems of Northland, the Hauraki Goldfield and the Taupo Volcanic Zone; and marine placers off the West Coast where an area of auriferous gravels has been outlined near Hokitika. There is potential in known deposits and prospects currently being evaluated for a large increase in gold production by the early 1990s.

Jan 1, 1986

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

The calibrated thermal IR data of part of Cambay Basin is used to determine surface temperatures and to detect the heat flow. Applying the conductive heat flow continuation technique, the three dimensional configuration of the hydrocarbon bearing reservoir was defined. The zone delineated by the present study coincides with the oil-bearing structures inferred by seismic survey. The results indicate the possibility of the technique as an effective tool in hydrocarbon exploration.

Jan 1, 1986

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

General design of pillars to ensure a continuing roof support during ex- traction is discussed. Practical problems associated with pillar extraction are Outlined.

Jan 1, 1974

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

By Jones IO

Although small units have been in use formany years, particularly in opal mining at shallow depths, there has been little effort in the past to explore the potential of the vacuum lift system in other more demanding applications. Recent developments in Western Australia by a small number of mining companies, contractors and manufacturers have seen the design and construction of several larger, more powerful units for use in winzing, shaft sinking, hoisting and spillage removal. Some of these units have proved very successful and suggest that they could be developed for a wider range of applications and duties in future.

Jan 1, 1984

A simple production technique has been initiated and implemented at Oaky Creek open cut coal mine to optimise recovery of coal from the relatively thin geological seams. The production technique is based upon minimising coal dilution through careful dragline operation and the selective use of mine mobile equipment to clean the top of coal. In addition, recovery of coal from the pits has been increased by refining blasting and dragline methods.The implementation of the recovery optimisation programme at Oaky Creek has provided significant economic benefits from increased yield through the preparation plant by the reduction in dilution, and from increased raw coal tonnage through improved pit recovery methods.

Jan 1, 1990

It is no longer adequate in running mines and quarries to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency. This requires efficient production and commercial processes together with systematic involvement of people in continuous improvement of processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. Unfortunately, even though these principles are proven in all industry sectors worldwide, they have not always been used correctly. This paper describes basic methodology for correct use of these principles to successfully improve the productivity of rock breakage production processes.

Jan 1, 1995

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

By Barnett DW

Financial risk analysis provides the tools to examine the uncertainty of capital decisions in new mining ventures. This paper explores the methodology by which financial risks can be studied and quantified. The most commonly used risk evaluation methods, such as sensitivity analysis and discount rate adjustment, are presented as an introduction to a more comprehensive discussion of stochastic methods of discounted cash flow analysis using Monte Carlo sampling. The discussion is illustrated with examples of a stochastic discounted cash flow. The advantages of Monte Carlo sampling in risk analysis are discussed together with its problems, particularly those originating from the correlation amongst the variables that determine the economic output of a mining venture, and the difficulties created by insufficient data, imperfect knowledge and complexity. The paper also surveys the most commonly used software used in risk analysis.

Jan 1, 1994