Search Documents

By T. A. Rickard

The Cripple Creek district occupies a cluster of foot-hills on the south side of Pike's Peak and is a portion of an extensive, though uneven, plateau which unites the eastern range of the Rocky mountains with the Sangre de Cristo. It is essentially a small volcanic area, of about 20 square miles, amid the granite of the Front range. But though, when regarded as a rich mining district, it may be considered as an isolated area,* yet, geologically, it is, as Whitman Cross has pointed out, only an outlying portion of a much larger volcanic region, which stretches to the south and west, around Silver Cliff and the Rosita hills, forming the picturesque country cut by the deep cañons of the Arkansas river and its tributaries. The mines are situated amid a volcanic complex, consisting of tuffs and breccias which have been penetrated by an extensive system of dikes and other intrusive masses. The prevailing formation is an andesite breccia, which lies upon the worn surface of the granite and fills the deep basin around a volcanic vent. The breccia, since its deposition, has been broken into by several eruptions of phonolite and, later still, by a series of thin dikes of basalt and other allied rocks of a highly basic composition. The successive sedimentary formatione which, elsewhere in Colorado, lie upon the basal granite, are not represented in the district; whatever sediments were laid down before the volcanic period must have been removed by erosion, and there is very little evidence which affords a datum-line whereby the geological age of the volcanic eruptions can be determined. Whit-

Jan 1, 1901

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By Kenneth Seaver

(San Francisco Meeting, September, 1915) INTRODUCTION IT is rather gratifying that in the field of the manufacture 'of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are common with us, until the actual 'completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with. such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick front highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion.

Jan 9, 1915

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By J. B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with aluminum sulfate. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1985

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

By David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand or magnetite, in water, and, (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended sand or magnetite pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous; vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the introduction of feed and withdrawal of products, 'so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary is get the recoveries and grade of product desired. Sizes usually cleaned are plus ¼ in. or plus 1/8 -in. in the United States and plus 1/16-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about 1/8-in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media processes is progressing rapidly and it is likely that equipment, media, and procedures will be developed to clean sizes down to 0.5 mm. efficiently and at low cost.

Jan 1, 1950

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By C. A. Wright

The average lead and zinc content of the ores mined and milled in the Joplin district is low as compared with that of other lead and zinc deposits throughout the United States. Because of this fact and of the high grade of the concentrates, the ratio of concentration is unusually high. Most of the operating companies have aimed to produce as high a grade of concentrate as possible in order to obtain the highest price for their product. They have done this at the sacrifice of the percentage of zinc recovered. The average percentage of zinc recovery is from 60 to 70 per cent. For percentage of recoveries from actual mill tests, see tables. The concentration is commonly effected by crushing the ore to ½-in. (12.7 mm.) size and subjecting it to a roughing and cleaning over two or more large Cooley jigs, of the Harz type, the finer sands being treated on the usual types of sand and slime tables. The treatment of slimes by flotation is being tested at several of the larger mills. Coarse Concentration When the ore has been hoisted from the mine it is dumped onto a chute leading to a grizzly made of iron bars, usually heavy rails, spaced 4 to 5 in. (101 to 127 mm.) apart. The oversize is caught on the grizzly, the mineralized pieces are broken with sledge hammers so as to pass through, and the boulders that are practically barren are sorted out by hand and trammed to the waste-rock pile. The proportion of waste rock thus sorted out varies from a fraction of 1 per cent. to 15 per cent., depending on the nature of the rock. Crushing The undersize material, 5 in. (127 mm.) or less in diameter, passes through the openings of the grizzly into the mill hopper below. From

Jan 1, 1918

By A. G. McGregor

During the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and equipment developed. Some of these features are described in this paper. Concentrate Hauling, Unloading and Sampling System (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences. A concentrate unloading pocket (Fig. 4), 180 ft.long, is provided at the smelting plant, which has a conveyor belt running throughout its length underneath the track. To unload a car, the vertical plug at the end of the car is lifted by means of a chain hoist which is supported by a trolley overhead. The gate at the end of the car is opened approximately 18 in. The removal of the plug leaves a hole down through the concentrates. The concentrates are poked through the hole from the top of the car until it is convenient for a man to stand on the bottom and draw one of the slats in the bottom toward the gate end of the car. The concentrates are then raked down with hoes on their natural angle of repose,

Jan 1, 1917

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By ir. H. Eraly

The allocation of miners to teams, and of teams to production faces, is complicated by the high degree of absenteism of miners in Belgium. Therefore, the exact knowledge of who is actually present at the beginning of a shift and of the exact skills of those present, enables the foremen and mine captains to constitute their teams before all men go down into the mine in the most effective way possible. This paper describes the system of attendance recording and of displays which the foremen use to constitute their teams and/or to interrogate the personnel data base in order to do so. It shows how the foremen dialogue with the computer, to change the function of a miner within a team, to another team, or the function of a team as a whole. The implementation of the system, data bases, and data communication equipment and procedures, is described. The benefits obtained are presented for each level of the company: foremen and team supervisors, engineers, mine management.

Jan 1, 1977

By W. H. Blauvelt

The only way in which the difficult problems of classification of coal for the manufacture of by-product coke can be solved is to analyze them by the use of scientific data. It is very easy to adopt classifications for coal for the manufacture of by-product coke along certain lines; we can easily say that for a certain class of metallurgical operation coke made from bituminous coal must not contain more than so much sulfur or more than so much ash and should yield certain returns in the by-products, tar, ammonia, benzol, gas, etc. Those points we are fairly clear on and I think it is hardly worth while to discuss them because I presume that they are familiar to most of us who have any occasion either to make coke or to use it. But there is a field in the manufacture of coke which we know very little about. For example, we are operating a plant on a certain mixture of coal. Suddenly our blast-furnace man or the user of the coke tells us the coke is not as good as it was before. The coke is analyzed and the coal is analyzed. Everything seems to be about the same as it was— the ash is the same, there is no more sulfur, and so on—but the coke, for the use to which it is put, particularly in the blast furnace, is wrong. What happens? The management decide to try a slightly different coal mixture. They do not necessarily raise the total hydrocarbons, the volatile matter in the mixture, nor change the sulfur or the ash, but they do make a change which improves the value of the coke for metallurgical use. The reason for this difficulty, as I see it, is the " combustibility " of the coke—I hesitate to use the word, but it is the best one I have available. Combustibility of Coke We know now that the combustibility of coke is a very vital point in many metallurgical processes and I think one of the most notable instances of the proof of this is the experience of the Carnegie Steel Co. in the production of coke at its Clairton plant. The history of that

Jan 1, 1930

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950