Search Documents

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

By C. E. Williams

THE Iron and Steel Division, A.I.M.E., is unique in this country in that it serves all phases of the iron and steel industries. Through its publications, its meetings, and its sponsorship of new technical developments in the industries, it has proved of great value. The various technical committees of the Division are the nucleus around which this service can be developed. The Blast Furnace and Raw Materials Committee has done excellent work. The need for beneficiation of iron ores is increasing and the economics of this operation are developing more and more in favor of increased activities. Ores that are slightly undergrade should be concentrated up to grade to supplant the present practice of mixing with higher-grade ores to bring up the average composition. Marginal ores that are not now being mined, or that are being mined and piled for future use, should be concentrated. The development of the use of sinter in the blast furnace, because of the elimination of fines, the advantage of better sizing of the charge, the resulting reduction of coke consumption, and increased output of pig iron per furnace, will make concentration and sintering become practical ahead of its natural time.

Jan 1, 1936

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."' The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

By HARRINCTON EMERSON

UNEMPLOYMENT is the most ominous shadow ahead of the industrial nations today. Only two great industrial countries are free from unemployment, France and the Soviet Commonwealth. In France the social unit is the family, not the individual. This has saved France. In the Soviet Commonwealth, development is proceeding so rapidly from agricultural to industrial that there is still a dearth of muscle workers in the non-agricultural enterprises. In the other industrial countries unemployment results both from acute temporary recession in industrial activities and from the rapidly increasing substitution of the machine for the man. Temporary recessions can be mitigated, alleviated by makeshifts, often ill considered. Secular recessions due to a fundamental change in the way of accomplishing physical, chemical results cannot be cured by any makeshift. There must be a period of transition. There is therefore before us the three- fold problem, immediate, prosimate and ultimate.

Jan 1, 1930

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896

By FREDERICK MCAKCCOY

THE production of tin from Mexico has never reached the point of being considered a national industry, but the distribution of tin ores is so widespread that there are possibilities that one day it may become of importance. Of the twenty-seven states of the Republic, tin claims have been taken up in sixteen. In all there had been taken up to the end of 1926, two hundred and twenty-five claims, of a total area of about 7400 acres. The first historical mention of tin in the Americas is found in a letter of Cortez to the Emperor, Charles the Fifth, of Spain, which is as follows: Speaking of his manufacture of some small cannon, he says: "For these reasons I took considerable pains to get copper from some provinces of this country, and bought it at a high price in order to get it quicker.

Jan 1, 1929

By J. T. Ryan

FIGURES for the first 11 months of 1935 indicate that the total coal production of the United States for 1935 will be approximately 416,000,000 tons, or almost identical with the production figures for 1934. Bituminous production will show a gain of about six million tons, and anthracite production a loss of about the same tonnage, compared with the previous year. This does not take into account so-called "bootleg" anthracite coal amounting to approximately 5,000,000 tons. Twenty-nine years ago, in 1906, the production of coal was almost identical with this year's production. At that time, 626,000 men were employed in producing this tonnage, which took a toll of 2138 lives from accidents. In 1935, approximately 540,000 men were required to produce the same tonnage with an estimated loss of 1155 lives. This shows definite safety advancement in the industry, but even so accidents are still costing an average of 3c. a ton more than they should.

Jan 1, 1936

By H. C. Meister

THE zinc-smelting industry of the United States has grown very rapidly in recent years and bids fair to outrival that of all other countries in the future. On account of the geographical situation of the chief ore-supplies, the industry may be divided into two main groups, the eastern and the western. The eastern and older group includes the works of Pennsylvania, New Jersey and Virginia, which practically control their own ore-supply. The western group includes the works of Illinois, Missouri, Kansas, Wisconsin and Indiana, which do not control their own ore-supply, but are compelled to buy the ore in the open market. It is for this reason that the western zinc-smelting industry has been undergoing continual changes since its inception 40 years ago. During the early discoveries of lead- and zinc-ore in the lead- and zinc-districts of Wisconsin and northern Illinois, the zinc-ore (sinithsonite or " bone " as the miner calls it) had no value and was considered waste; but later, when this ore was found in large quantities, it attracted the attention of metallurgists, which finally resulted, during the early sixties, in the building of the Matthiessen & Hegeler Zinc Works at LaSalle, Ill., the pioneer zinc-works of the West. A few years later, zinc-ore was discovered associated with the lead-ore in Jefferson county, southeastern Missouri, which started the industry at Carondelet or South St. Louis. Still later, the discoveries of zinc-ore in the lead-ore region, first' at Granby and then around Joplin, lead to the introduction of the industry in the southwest Missouri and Kansas districts. At first the development of the industry was slow, but it progressed steadily and it is now one of the leading metallurgical industries of the middle West.

Jan 1, 1905

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By A. J. Terrones

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,' by Barrell on Marysville, Mont.,' and by Gold-schmitt on the Oslo district, Norway,' laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf' made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control" in ore finding. Some years later Harrison Schmitt" fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed. Primary exploration and careful sampling of recognized structural targets were instrumental in outlining the copper ore potential at the Antamina and Tintaya districts, thus proving the benefits and reward of careful geological examinations in this type of deposit. The Magistral District: This district lies in the Province of Pallasca, Department of Ancash, in northern Peru, at 8o 16' S and 77" 47' W. High to medium grade copper orebodies in garnetite, bordering a quartz monzonite stock, are exposed at the bottom of a glaciated valley in the western slope of the Andes at 4250 m (14,000 ft)* elevation.

Jan 1, 1959

By H. H. Moss

OXYACETYLENE .cutting has experienced rapid development in the last few years and greater advances and expansion and broader application may be expected in the immediate future. Marked changes in cutting practice may be expected as a result of the advances in metallurgical science that have produced special alloy steels with properties requiring different cutting techniques than for ordinary low-carbon steels. Much current attention is being directed to those problems of modified cutting practices. Cutting has thus ceased to be merely a shaping problem. It is rapidly coming to have a predominantly metallurgical aspect. The problem is no longer how to cut a given shape, but how to cut a given steel. The answer

Jan 1, 1936

By J. F. Butler, H. W. Paxton

The vapor pressures of manganese in equilibrium with several alloys in the iron-manganese-carbon system between 1200° and 1275°K have been measured using the Knudsen effusion technique in conjunction with a vacuum microbalance. The effect of orifice area of the effusion cell upon the measured pressure has been determined. The binary iron-manganese system shows small negative departures from ideality, and the system of mixed carbides, (Fe, Mn)7C3, in equilibrium with graphite behaves ideally. THIS work is a continuation of the investigations in which the Knudsen effusion method has been used to determine thermodynamic activities in systems and at temperatures of interest to metallurgists. In a previous publication,' the free energy of formation of Mn7C3 was determined and some preliminary work on the solution behavior of this carbide with the hypothetical "Fe7C3" was reported. The present work deals with this latter topic and also includes data on the binary ir-on-manganese system. EXPERIMENTAL METHOD The Knudsen effusion method was used to measure the vapor pressure of manganese in both the alloy and carbide sections of this investigation. This dynamic method of vapor pressure measurement presents a problem when studying solid alloy systems in which one of the components has a much larger vapor pressure than the others. Over-all depletion of the alloy in the most volatile component will occur during evaporation so that the pressure of that component will decrease. Even more serious than the over-all concentration change is the surface depletion of volatile component in the alloy brought about by the slow rate of diffusion of this component from the interior to the surface of the solid particle. Since knowledge of this surface composition is necessary in order to relate it to the activity determined through the measurements, changes in surface composition from the analyzed bulk composition are to be avoided in dynamic vapor pressure studies of solid alloys. The system under investigation in this study presents the problem of surface depletion of manganese since its pressure at 1230°K is 105greater than iron and 1020 greater than carbon. Since the existence of a volatile manganese carbide had been ruled out previously,' the high manganese pressure relative to iron and carbon insured that the only species leaving the effusion cell was manganese. Therefore, the effusing species required no analysis so that the manganese pressure was determined directly from the weight loss of the effusion cell. In order to detect small weight losses near the beginning of effusion, a vacuum microbalance was used to weigh the cell continually. These initial weight loss data allowed the rate of manganese effusion to be determined before the surface of the alloy became depleted in manganese. The apparatus used in this investigation is shown in Fig. 1. Temperature was measured using chro-

Jan 1, 1962

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

Executive A R LEDOUX, Chairman ARTHUR S DWIGHT CHARLES F RAND E P MATHEWSON J V W REYNDERS Membership E DEGOLYER, Chairman W Y WESTERVELT, Vice-chairman WILLIAM H BASSETT H G MOULTON C MINOT WELD Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER Library GEORGE C STONE,' Chairman JOHN H JANEWAY ALEXANDER C HUMPHREYS, ROBERT LINTON FREDERICK F SHARPLESS

Jan 1, 1923