Search Documents

By William P. Blake

The salt-beds at Salton, on the line of the Southern Pacific railway, in San Diego county, California, have been successfully worked for many years by the corporation known as the East Liverpool Salt Co., and the salt has been largely used upon the Pacific coast generally and in the interior. But the industry has lately been destroyed by the overflow from the Colorado river. The salt is dissolved, and the waves of the Salton sea now roll 50 ft. above the site of this once thriving and growing business. The salt-bed was evidently the residual accumulation from the waters of an ancient lake, which I have named Cahuilla, from the name by which a large part of the valley—the home of the Cahuilla tribe of Indians—is known. The deposit covered a comparatively small area in the lowest part of the valley, 280 R. or more below the sea-level. This depressed area is now generally known as the Colorado desert, but has a soil of wonderful fertility wherever water can be had on its surface. The deserted beaches, and the water-lines, only a few feet above tide-level, upon the rocks of the bordering mountains, as well as a great abundance of shells in the soil, all bear decisive testimony to the former occupation of the valley by water. The depression is topographically the northern end of the Gulf of California, from which it is now separated by the delta of the Colorado river, extending practically from the mouth of the Gila river across the valley to the coast mountains on the

Jan 1, 1908

By Barbara A. Thompson

A previously reported high-resolution method for the location of boron-rich areas in metallurgical and biological specimens was been adapted for general use on a routine basis. The rnetlzod utilizes neutron activation and autoradiograpizy. Alpha-particles emitted by boron nuclei upon neutron capture are recorded on a photographic emulsion. The resulting a-particle tracks show the location of boron-rich areas. Experimental techniques, interferences, and limitations of the method are discussed in detail. The method is most useful where there is marked segregation of boron. In this type of sample, the segregation can be observed when the nominal boron concentration is as low as 0.0006 pct. THE positive identification and location of boron-rich areas in metals is frequently of great interest in metallurgical work. Unequivocal identification is often difficult to make by conventional metallo-graphic methods. Recently, a method has been described which accomplishes this objective by neutron activation and autoradiography.l-3 The method can be described briefly as follows. Upon neutron capture, a -particles are emitted by boron nuclei according to the following reaction: ,Blo + n - ,a4 + 3Li7 + 2.4 mev The energy is dissipated as kinetic energy of the products. By irradiating a boron-containing sample in contact with a photographic emulsion and subsequently developing this emulsion, a-particle tracks are obtained whose location corresponds to the location of boron-rich areas in the sample. Two factors combine to make the reaction extremely specific for boron. The first is the unusually high (755 barns) cross section of boron for thermal neutron capture. The second is the higher neutron energy required to produce (n, a ) reactions in essentially all other nuclei except lithium. These two factors make the method specific for boron by six to seven orders of magnitude when a predominantly thermal neutron source such as the Brookhaven reactor is used. The reported limit of detection of this method is of the order of 0.01 pct B., The present work was originally undertaken to determine whether this limit could be lowered by use of a thinner emulsion. However, initial experiments showed that in order to use the method at all, it was necessary to reestablish the optimum experimental conditions in terms of the available irradiation facilities. It is the purpose of this paper to describe these experimental conditions in detail, to discuss the factors influencing sensitivity, and to evaluate several techniques for increasing sensitivity. EXPERIMENTAL A) Preliminary Experiments—The first measure-ments were made using samples of crystal oriented silicon steel containing various concentrations of boron. In the later experiments, samples of various high-temperature alloys such as M-252, hcoloy 901, Nichrome V, and so forth, were used. Faraggi, et al.,2 reported that the lower limit of sensitivity in this type of sample was about 0.01 pct B using nuclear emulsions of 50- u thickness. but that it should be possible to extend this limit by the use of thinner emulsions. Accordingly, we first used Kodak Auto-radiographic Stripping Film (Permeable Base) which has an emulsion thickness of only 5 µ. This was mounted on the metallographic specimens according to the technique described by Boyd.4 The emulsion remained in contact with the metal surface throughout exposure and development. Since the emulsion is transparent after development, the autoradiograph and metal surface can be viewed simultaneously and any correlation between film blackening and structure of the metal can be made directly with no problems of realignment. Because the silicon steel is readily attacked by moisture alone, it was necessary to apply a protective coating to the metal surfaces before mounting the emulsion. The coating was made extremely thin in order to absorb as few a-particles as possible. Boyd4 and Gomberg5 have discussed various plastics used for this purpose; however, none was sufficiently impermeable to prevent chemical attack of the steel during the developing process. This attack resulted in the production of gross chemical artifacts in the emulsion. It was, therefore, necessary to use the method of Wolfsberg and John6 as follows. A very thin (approximately 1 µ) coating of Plexiglas II was applied by dipping the sample in a 2 pct solution of Plexiglas II in dichloroethylene. Then, because the emulsion will not adhere to Plexiglas 11, a thin coating of Parlodion was applied in a similar manner using 2 pct Parlodion in iso-amyl acetate. No protective coating was necessary with the high-tem-

Jan 1, 1961

THE opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced. Mr. Franklin B. Gowen, who addressed the Institute as follows MR. PRESIDENT AND GENTLEMEN : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of gentlemen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a pro¬cess that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers, * A joint discussion of the subject of Technical Education, by the members of the American Society of Civil Engineers and the American Institute of Mining Engineers, was held in the hall of the Franklin Institute, on Monday evening, June 19th, and Tuesday morning, June 20th. This discussion has been printed in a separate pamphlet by both societies.

Jan 1, 1877

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By J. M. Callow

THE results obtained by pneumatic flotation throughout the country on all classes of ore, and. the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practice. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cycloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of. flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles, by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by, Dr. Rudolf Gahl- on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. COMPARATIVE SENSITIVENESS AND ATTENDANCE Concerning 'the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that; with the exception of about 24 days at the end of the testing 'period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the conclusions drawn on page 562 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls, for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be, of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 2, 1917

By S. C. Jones, J. A. Davis

This paper describes displacement mechanisms of micel-lur solution slugs, displuced by a thickened water "mobility buffer", in a glass micromodel and in consolidated Berea sandstone cores. Colored motion pictures, taken through a microscope, recorded interactions on a pore-to-pore bash in the micromodel. Production and differential pressure data from consolidated cores previously waterflooded to residua1 oil saturation revealed displacement mechani.sm.s macroscopically. Oil is displaced miscibly, while interstitia1 water is displaced immiscibly by the injected micellar. solution slug. Part of this water is dispersed and carried near the lead ing edge of the .slug, and some may remain as a residual saturation. Thickened water displaces any residual water. It also emulsifies with the. slug material, thereby displacing it. The displacement sequence forms banks of oil and water with relatively constant fractional flows, saturations, and mobilities. The mobility of oil and water flowing ahead of the .slug defines .slug viscosity required for stable displacement. Equations are presented that describe. several aspecis of the displacement flow behavior: oil breakthrough, oil cut during production of the stabilized bank, breakthrough of banked water and the resulting decreased fractional flow of oil, fluid mobilities, etc. Breakthroughs, calculated from the equations, are compared with experimental data. Slugs of micellar sollution, ranging from 1 to 5 percent PV, produced unusually high oil recoveries (up to 100 percent) in previously waterflooded consolidated cores. Investigation of the effect of mobility buffer size on oil recovery indicated that recovery is reduced in 3-in. X 4-ft cores for mobility buffer sizes .smaller than 50 percent of the pore volume. Introduction A new oil recovery process,* conceived in 1962, utilizes a slug of micellar solution' that has sufficient viscosity to avoid an unfavorable mobility ratio with respect to the oil and water it displaces. These micellar solutions are composed of hydrocarbons, water, and surfactants, and may contain electrolytes and co-surfactants. The micellar solution is displaced by a "mobility buffer". The mobility buffer is a bank of reduced-mobility fluid, preferably an aqueous polymer solution. The entire system is displaced by unthickened water. This paper describes some of the microscopic and macroscopic displacement mechanisms observed during laboratory development of the fluids for a potential field test. Microscopic phenomena were observed photographically in a specially constructed glass flow model and macroscopic data were taken from constant rate, tertiary displacements conducted in Berea sandstone cores. Qualitative Description of Micellar Solution Flooding This section qualitatively describes displacement mechanisms that occur when a slug of micellar solution is injected into a previously waterflooded core. The slug completely removes oil from the portion of core it contacts, and banks oil in the process. The oil saturation in this bank and the flowing WOR reach definite, fixed values that are determined by water and oil mobilities and slug characteristics. This zone of constant WOR and oil saturation will be called "stabilized oil bank" in the following discussion. When this stabilized bank reaches the outlet end of the core, the oil cut jumps from zero to a constant value equal to the fractional flow of oil. Saline water has little or no solubility in the slug. Because of this. the slug displaces in-place brine immiscibly. During slug injection, most of the brine is displaced ahead of the slug, some is carried along in the leading portion of the slug, and part of the brine may become immobile. The immobile, residual brine is later miscibly displaced by thickened water. Displacement of all the oil and only part of the water during slug injection results in a higher fractional flow of oil ahead of the slug than occurs when all the water is displaced after injection of thickened water is begun. The slug spontaneously emulsifies fresh (low-salt content) water. By emulsification, the slug can become infinitely diluted, and hence totally displaced, by thickened water. Fluid saturations in the core are shown schematically in Fig. 1. Parts A and B show conditions before and after the start of the thickened-water injection, respectively. Since thickened water displaces any residual brine by-

Jan 1, 1969

By C. O. Brawner

FACTORS THAT INFLUENCE STABILITY AND STABILIZATION METHOD The most effective stabilization method and design can only be developed if the cause(s) and mechanics of the slide are known. Therefore, it is important that the stability be evaluated by an engineer who has had extensive rock stability experience. The most important factors that influence stability are structural geology, ground water, blasting and the mining method or methods. Structural Geology - The majority of failures in rock slopes occur along discontinuities in the rock (joints, bedding planes, shear or fault zones, etc.). Therefore, on all surface mining projects, the development and maintenance of a comprehensive structural geologic mapping program should be a first priority program that is considered a part of the operations function. This program should include mapping all major features - faults, shear zones and through going joints. All structural features which could influence stability should be mapped and presented in a structural domain format for the entire mine (Canmet, 1977). Where planes, wedges or blocks will be undercut by the mining excavation, shear strength and strain to failure tests should be performed on the joints, fault gouge and gouge-rock contact surfaces. These tests must be performed on the samples in the direction of potential slide movement and must determine the range of peak and residual shear strength values. A preliminary assessment of friction angle can be obtained from measurements of failed surfaces in the field (Figure 1) or from core sliding tests (Barton, 1981). An assessment must be made of the past geologic history of

Jan 1, 1983

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938

By Charles M. Rolker

The main tin-producing regions of the world are known to be England, Australia and the Dutch East Indian possessions, chiefly Banca and Billiton. During recent years, the tin of the Malay Peninsula, exported from Penang and Singapore, has been coming prominently to the front. France, Austria, Hungary, Germany, Spain, South America, Russia and China still present insignificant figures. The conspicuous part which the Dutch possessions in the Indian Archipelago have taken in supplying the world with tin, is well known. Tin was discovered in Banca as early as 1710, and has been produced there ever since; but the supply has been most important since Banca came fully into the possession of Holland, in 1821. In Billiton and the adjoining island of Singkep, the existence of tin was known prior to 1822.* The Lingganese knew of its existence in the valley of Embalong, from creeks and streams in the neighborhood of Tima and Simper hills, on Billiton and also on Singkep island, but the prevailing superstition that tin-mining brought misfortune, influenced them to let this industry lie idle. The attempts of the Dutch government to test this question were lukewarm, perhaps by reason of the fear of reducing, through new discoveries, the price of Banca tin, and the island was abandoned in 1826, leaving only a military post. In 1850, Dr. Crookewit, a chemist and naturalist, was sent out to verify the rumors that tin existed in Billiton. His report was unfavorable; but in 1851 Mr. C. De Groot, a mining engineer, found tin readily, and the active work on Billiton dates from that time. Less than 600 tons were produced during the first ten years, and 3000 tons in the next decade. Billiton tin-mining is done by

Jan 1, 1892

By George Lehman

THE Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the ?shrinkage-stope" or "caving" methods ) a lower extraction of, the developed ore, at a lower mining cost. ORE-DRAWING TESTS To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or "caving" methods. As no definite information regarding the question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore.

Jan 9, 1916

By P. Marier, T. R. Ingraham

When cylindrical powder compacts of nickelous oxide (NiO) are heated in an equilibrated stream of SO3, SO,, and 02, in the temperature range 500°to 800°c, tlickelous suljate (NiSO4) is formed as an adherent layer on the oxide. The reaction is diffusion-controlled, with an activation energy of 13 ± 3 kcal per mole. When cylindrical powder compacts of NiSO4 are heated in a stream of dry nitrogen in the temperature range 1000 0to 11500C, NiO is formed at a well-defined interface between the sulfate and oxide. The interjhce migrates into the sulfate at a constant rate at a constant temperature and gas flow. The reaction rate increases with increasing gas flow and decreases with increasing partial pressure of SO3 in the gas stream. Resolution of the partial-pressure data with a Lang-itzliir Adsorption Isothern suggests that about 80 pct of the NiO interface is covered with SO3. The heat of adsovption is about 68 kcal per mole. The activation energy of the decomposition process is 61 ± 3 kcal per mole. MOST of the work reported on the formation and decomposition of nickel sulfate is related to thermodynamics.1-3 No quantitative work has been reported on the decomposition process. The only kinetic work reported on the formation is that by Fletcher and shelef.4-6 whose main purpose was to study the effects of alkali metal sulfate additions on increasing the rate of nickel sulfate formation. They found that, in the absence of an additive, only small amounts of sulfate were formed and the kinetic data were difficult to interpret. However, they suggested that the sulfa-tion of nickel oxide is a diffusion-controlled process for which the activation energy is approximately 17 kcal per mole.6 In this paper, both the formation and decomposition reactions will be examined; and based on the effects of temperature, flow rate, interfacial area, and partial-pressure of sulfur trioxide, mechanisms and activation energies will be suggested for both processes. EXPERIMENTAL Material. The nickel source material used in all experiments was Baker and Adamson Reagent Grade NiSO4. 6H2O, for which the following analysis was supplied by the manufacturer: C1, 0.001 pct; NO3, 0.005 pct; Co, 0.02 pct; Cu, 0.005 pct; Pb, 0.002 pct; Fe, 0.001 pct: insol, 0.005 pct. The anhydrous sulfate was prepared by heating the hydrate at 420°C in a muffle furnace for 5 hr. Nickel oxide was prepared by decomposing the sulfate at 950°C over a period of 10 hr. Method. The technique used for measuring the rates of formation and decomposition was developed earlier in these laboratories.7-8 The method is based on the observation that the kinetic parameters of a reaction can be established in a flow system, with specimens prepared by compacting powder to a uniform pellet shape. The results are identical with those established with solid polycrystalline specimens or single

Jan 1, 1967

By R. D. Carnahan, J. E. White

A study of dispersion strengthening in TD-Nickel (nickel plus 2 vol pct Tho2) was conducted employing microstrain techniques at ambient room temperature. It was found that optimum strength was due primarily to the incorporation of stored energy developed by a variety of thermal-mechanical treatments. The relatively low strength of the recrys-tallized condition implies that the dispersed particles themselves offer only token resistance to deformation. The development of resistance to large-scale recovery or recrystallization at temperatures near the melting point requires a more extensive sequence of strain-anneal cycles than does the development of optimum strength. A micro-Bauschinger effect was observed which appears to be related to the lattice resistance to the movement of free dislocations. The effect was nearly identical to that in pure nickel indicating that the presence of the dispersed phase and considerably increased dislocation density (stored energy) only alters the number or effectiveness of barriers. THE early stages of deformation of engineering materials can be conveniently studied by utilizing strain-gage techniques which permit resolution of strains less than 5 X 10-7 in. per in. for testing in four-point bending (Carnahan and white1). The present investigation, part of a continuing study on the very early stages of deformation, was designed to reveal the true role of a dispersed phase in promoting high strength in a commercially available dispersion-strengthened alloy. Although this technique has been used for some time to study microdeformation in pure metals and alloys, it has just recently received attention as a means of investigating dispersion strengthening. Studying the very early stages of deformation in alloys which depend upon a finely dispersed inert phase for strength may prove to be a very important method for a better understanding of these materials. It is essential to obtain considerable clarification of actual dislocation movement and the kinds of deformation barriers which exist before optimum properties can be designed into this type of material with any degree of confidence. Considerable research on a variety of dispersion-strengthened materials has resulted in two different schools of thought regarding the strengthening mechanism. One faction2-4 favors the idea that the particles themselves resist the motion of dislocations. The criterion for yielding is the fracture of the dispersed second-phase particles due to an array of piled-up dislocations. Other invesfigators5-a have shown that particles are effective primarily by allowing a greater buildup of stored energy or dislocation density through thermal-mechanical treatments in the composite than the pure matrix material. The particles themselves, then, are not exclusive obstacles, but the complex network of particles, dislocation tangles, subboundaries, and grain boundaries are strength determining. The development of such a complex dislocation network in SAP has been studied recently in some detail by Goodrich and Ansell. The ability of dispersion-strengthened alloys to resist softening or recrystallization is also of considerable importance; however, the criteria for maximum stability may not necessarily be those for maximum strength. In this study, in addition to the evaluation of the microstrain properties of TD-Nickel, it is felt that considerable clarification of the true dependence of strength and stability on the dispersed phase is shown. I) MATERIAL AND PROCEDURE TD-Nickel is a dispersion-strengthened alloy developed by the E. I. DuPont de Nemours Co., which contains 2 vol pct thoria (Tho2) in a pure-nickel matrix. The average ThO2 particle size is approximately 0.1 p and the interparticle spacing is less than 1 u. The material was supplied by DuPont in two conditions: hot-extruded bar stock, and stress-relieved cold-rolled sheet 0.025 in. in thickness. The bar was extruded at 2200°F from a cold-pressed and sintered billet. The sheet stock was prepared from the extruded material by a process involving ten or more 50-pct cold reductions by rolling with intermediate anneals at 1800° to 2000°F. Test specimens used in this study were prepared in the form of rectangular parallelepipeds measuring 0.375 by 1.375 in. in thicknesses ranging from 0.025 to 0.040 in. Samples prepared from sheet and extruded stock were mechanically polished before heat treatment and were handled with extreme

Jan 1, 1964