Search Documents

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By R. B. Hoy, Stanley J. LeFond, K. Reckling

World production of natural diamonds prob¬ably exceeds 50,000,000 carats a year. The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, and the Republic of South Africa third. Diamonds are also mined in South-West Africa, Angola, Ghana, Sierra Leone, and other African coun¬tries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today in India, which was the first source of commercial production. In the U.S., efforts at commercial diamond mining have been con¬fined to a small area near Murfreesboro, Ark. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2000 years ago, only about 130 tons have been mined. In order to obtain 1 g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential ma¬terials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic indus¬trial diamonds are now of a quality that per¬mits wide substitution in the fine-grained sizes. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to "modify" light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem dia¬mond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today. About 1475, a Flemish cutter named Van Gerquem discovered that diamond dust on an iron wheel would polish facets on a diamond to provide more brilliance and fire. Cutters continued to experiment with facets, and shortly before 1700 a Venetian cutter named Peruzzi developed the 58-facet brilliant cut. With the development of the science of optics, cutters have learned more about the behavior of light within the diamond. Early in the 20th century, they learned how to angle Peruzzi's

Jan 1, 1975

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By Yves Dardel

INTRODUCTION SINCE the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts,2 then Baukloh and Oesterlen,3 during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreau,4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per 100 g of metal. Winterhager,5 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitz6 as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhauser8 extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per 100 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per 100 g, while that of the usual apparatus was only about 0.2 cm3 per 100 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. [ ] Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of Eborall and Ransley, as well as the earlier apparatus,

Jan 1, 1948

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper&apos;s vocabulary, refining practice consists in

Jan 1, 1951

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. &apos; The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Andrew Hyslop

IN our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys¬tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1948

By J. H. Bucher

The effect oj strengthening by the precipitation of CbC on the toughness offerrilic steel (0.11 pct C, 0.74 pct Mn, 0.02 pct Cb) was stlrdierl. A g-veater degree of pvecij~itatiotz strengthning is ohtaznable by aging the so11ution-treated steel rtt velaticely Low temperature was (1050" to 1l0O3F) than at higher temperatures (I150" to 1200°F). Tlzis ),eslrlts because a finer dispersion of CbC is obtained. However, the ductile-brittle transition te~ripertltlo.e is raised approximately tlzjeee tirues as IFLIIC~ perv a given yield stress increase) by aging in the lower tempareture range, as opposer1 to the Irigher temperaturee range. This is proposed to result pl-iir~avily because different precipitation distributions ar-e associated with the different aging -treaments. For tile steel aged at 1050" and 1100 F, heavy: precipitation on disloccctions occurs resulting in a high degree of rlislocution pinningh tl~us lowevirzg- the toilguiess. in tll c(.rise of the steel aged at 1150 &apos;a?zd 1300"F, Pvecipitatiol~ is irzove g-enerally distributed throughout the matrix rather limn preferentially on dislocations.; and Ike detlsitj, oj mobile dislocations is not sttyong-ly affected. THE most effective means of strengthening hot-rolled ferritic steels are grain refinement and precipitation hardening. It is well-known that grain refinement increases both the strength and the toughness. However, the upper limit of yield strength obtainable by grain refinement alone is about 60,000 psi,&apos;12 i.e., without the formation of acicular structures of lower toughness. The most economical means of obtaining higher strengths is the addition of small amounts of elements such as columbium, vanadium, and titanium which form carbonitrides. These precipitates are very effective in increasing the strength, but the ductile-brittle transition temperature is is Although it is agreed upon that precipitation decreases the toughness, there has been little effort to isolate the causative aspects of embrittlement. The purposes of this research are to assess quantitatively the embrittlement associated with different precipitate distributions and morphologies, and to correlate the degree of the embrittlement with the microstruc-ture. In this manner, a more fundamental insight into the mechanism of embrittlement may be gained. The steel selected for this purpose was a low-carbon, columbium-bearing steel which, after solution treatment, was aged in various time-temperature cycles while attempting to hold all other microstructural variables constant. MATERIALS AND PROCEDURE The composition of the steel used in this investigation is given in Table I. Starting with commercially hot-rolled material 0.074 and 0.280 in. thick, tensile blanks were cut from the thinner material and sub-size Charpy blanks from the thicker stock. The steel had been rolled using a low finishing temperature and rapid cooling after hot rolling to produce grain refinement. Also, chemical-extraction analysis and electron-microscopic examination revealed that the cooling was rapid enough to suppress any significant precipitation of CbC. Therefore, the as-rolled steel is essentially in the solution-treated condition in terms of the precipitation reaction, and it was used as the base material in this investigation. The room-temperature tensile properties of the as-rolled steel aged at 1100", 1150", and 1200°F for various time intervals were determined, see Table 11. The ductile-brittle transition behavior was studied for smooth and notched tensile specimens, and longitudinal half-size (0.200 in. thick) Charpy V notch specimens aged at 1100" and 1150°F for various times, also Table 11. In addition, tensile specimens aged for single times at 1050" and 1200°F were evaluated with respect to their ductile-brittle transition. Only one 1050°F treatment was used because of the extremely slow kinetics of precipitation at this temperature and because no significant difference between 1100°F aging was observed. Only one treatment at 1200°F was used because aging at this temperature alters the shape of the grain boundary cementite particles present in this steel and complicates analysis. The design of the tensile specimens is given in Fig.1.

Jan 1, 1968

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954